The URL can be used to link to this page

Home My WebLink AboutTEST REPORT - 23-00416 - 1212 Barney Dairy Rd - Solar PanelsTest Report For ANSI/CAN/UL9540A Test Method for Evaluating Thermal Runaway Fire Propagation in Battery Energy Storage Systems [Unit Level] Report Number: Date of issue: Total number of pages Test object / Model: Applicant's name Address: CQES220800015301 2022-09-07 40 Lithium Ion Battery R-Bracket Shanghai PYTES Energy CO., Ltd. No. 3492 Guangming Jinqian Road, Qingcun Town, Fengxian District, Shanghai, China Unless othemise agreed In writing, this document Is Issued by the Company sub)ect to its Gen" Conditions of Service printed overleaf, ava liable on request or accessible at httoa:Uwww-an..0Um;enrterma-erW-Contlaiona. Attention is drawn to the limitation of liability, Indemnification and Jurisdiction issues defined thirem. Any holder of this document is advised Mal mformstion contained hansom reflects the Company a findings at the limo of its Intervention only ena within the hmlts of Clients msUuctlons. d any. The Company's sob responsiWity is to Its Client end this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents This document cannot be reproduced except In lull. without prim written approval of the Company. Any unauthorized alteration, forgery or falsification of the content m appearance of this document is unlawful and offenders may be prosecuted to the fullest extern of dts law, Unless otherwba stated tM results shown in this test report refer only to the sampla(s) tested and such zD semple(s) are retained for 30 dayionly.After,.. To che" it,. urlhenbclty.1 testing unspactlon report 6 cerullcele, pi.... contact us et telephone iee•7a51$3071443, r en,.rll Cf/ Onc ciiec MOTvn+ corn dim b9,(biFg kKft Sfett"DOMDa p 0ft1 alfah "Nft.0drMEm 1�1 4O 260 I (86-23)81071W www.egagroup ow m �! ti9F �pI�Atil iifSi it2$d16� I1i9F1EY9li'#AEtM Y14r 1 090: 402260 t WM)863678001 sgs.dana®sgs.can Member of the SOS Group (SGS SA) Project No.: CQES2208000153BA TRF_UL 9540A Unit_V1.0 Page 1 of 40 FF Al 14 Report Number: CQES220800015301 Manufacturer: Shanghai PYTES Energy CO., Ltd. Address: No. 3492 Guangming Jinqian Road, Qingcun Town, Fengxian District, Shanghai, China Factory: Shanghai PYTES Energy CO., Ltd. Address: No. 3492 Guangming Jinqian Road, Qingcun Town, Fengxian District, Shanghai, China Test object / Model: Lithium Ion Battery R-Bracket ANSI/CAN/UL9540A:2019 "Test Method for Evaluating Thermal Run ay Fire Test specifications: Propagation in Battery Energy Storage Systems Fourth Edition, Dated November 12, 2019 Date of receipt: 2022-07-18 Sample No.: Customer ID Test Period: 2022-07-18 to 2022-08-15 Issuing Laboratory: SGS-CEC New Energy Technology (Chongqing) Co., Ltd. Address: Affiliate No. 6, No. 2 Fuyun Road. Shuangfu Street, Jiangjin District, Chongqing, China (No.1 Laboratory Building, Chongqing Energy College) SGS-CEC New Energy Technology (Chongqing) Co., Ltd. Testing location: Affiliate No. 6, No. 2 Fuyun Road, Shuangfu Street, Jiangjin District, Chongqing, China (No.1 Laboratory Building, Chongqing Energy College) Test Result: Refer to summary of test results page for details. Remark: Test results reported relate only to the items being tested. Tested by / Witness by Ryan Hu Project Engineer Reviewed by Jerry Xiao Technical Manager tti q� so" twill 116 Unless otherwl :o agreed In will this document is lbeded by the Company subjeed to Its Ganoral Conditions of Service p0riled oved0at. available on request or amssible ikwand-_rn dittorkL Attention Is drawn to the brhdall- al tfablW, IndemnlAcallon and J.riadlctlon esues detlned Ihemeln Any holder ofInformation contained hereon reflects the Company's Rndhq. el the hme of it, it e[— upon .Ny end wtthm the Um,b of Cl.eht's nshoctlors, I en;, The Conpeny'> sole responsibility Is to Its Client and this dowinenl does, not exonereta Parties 10 ■ transaction Ifom axerdMng all their rights and obligation underthe lrensaction docvments,Thisdocument cannot be reproduced exceptlnfufl, without prlorwntlan approval ofths Comperry. Any u neut h0r42ed eltaratl0n, forgery or faistficallon of the content or appsarence W this document is unlawt0l and offenders maybe prosecuted 1. the fullest @.tent or the law. Unless othe,wlse stated the results shown In this lest report refer only to the sampla(s) tested and such M�T��SIt�011� samples) ere retained for 30 days onry- c AtlanUon Toc thenticlty of lasting line pectlon report a—tlflule•pi....coot.clu.alel.phana:le6.755)a3C71443. br email: CM C 94COm SGSCEiCa.LIdIIMIrM0.lbiWpnnptasrwyu9eKi¢IUY40ai0�4phr�l t 7�eD�P?407180 1( 111636►M www.spapmup.cam.m `w^-_-_ 14S•1�ffitIIIIIIIi ails*izgMe#(IIEFIt�tII�AtlilIIttlE�1 KN:402M t(t1601063676001 aye.cNno@ge.mm Project No.: CQES2208000153BA Member of the SGS Group (SOS SA) TRF_UL 9540A Unit_V1.0 Page 2 of 40 [Summary of Test results] Cell Level Test Cell model: CB27173204EA Project No: CN21GRDU 001 Cell Design: Thermal Runaway Methodology: Cell Surface Temperature at Gas venting: Cell Surface Temperature at the onset Thermal Runaway: Gas Composition: Lower Flammability Limit: Burning Velocity: Pmax: Thermal Runaway was Induced in the Cell or not: Cell Vent Gas is Flammable or not in Air: CB27173204EA External heating 209.4"C 270.7uC Hydrocarbon, H2, CO2, CO 5.6 Vol% at ambient temperature 4.5 Vol% at 200 C 83.6 cm/s 1.015 MPa Induced Flammable r------------ -------------------------------------------------------------------------------- I I I I I Unit Level Test Model: R-Bracket Report No: CO ES220800015301 I I I I i T T 1 I 1 I I I I I I I I 1 --------------------------------------------------------------------------------------------- Remark: This report only evaluated unit level test which is listed inside the dotted box. Unless otherwise agreed In writing, this document Is Issued by the Company subject co its General Conditions of Service printed overland. available on request or accessible at httoa:llwww.aaa.camlarJTerms-and-Conditions. Albnbon Is drawn to the limitation of liability, w, il• % xx'' Indemnification and jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reflects •yam the Company's Gndlngis at the time of its Inlerven0on only and within the Omits of Clients InstruWons. if any The Company's sob r�_ responsibility Is to Its Client and this document does not exonerate pardea to a transaction from exercising all their rights and obligations under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document Is unlawful and offenders maybe prosecuted I:; r, to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such ynn6at1Tta51gSemto'; sample(s)are retained for 30it" onl Attenllon To check The authenticity of resting r inspection report A certificate. Ti contact s= talephon.-104-755)630'1443 a small'. C"'DecchochilkOYs.cgm A1Yh(b41b]hM�4 tllrlOiYtt(�sY14 f�f� i B fdO�B h 402260 t M")86387M wwititsMrolq.lwm.en r s"` a �® iff s�iM�Ail6yiA8kllt$M6$ I t9F16i�t¢IRtalt�!ltEr i 16M: 407180 t ler>-M)SMIST dot Ana&P— Member o1 the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 3 of 40 [Test object Description] Table 1: Description of component cell Model: Manufacturer: Nominal capacity: 100 Ah Nominal voltage: 3.2 V Chemistry: Lithium ions, LiFePO4 Charge current: 100 A Charge current: 100 A Maximum charge vnM�ge: 3.65 V Ir Cut-off Voltage: 2.5 V External dimensions: 207.01±0.E3mm `174.7mm±0.6mm ` 27.5mm±1.0mm UL 1973 compliant: ❑ Yes / 0 No N/A UL 9540A report provided: ® Yes / [❑ No Reference: Report No. CN21 GRDU 001, issued by TUV Rheinland � r Figure 1. View of component cell Unloss otherwi- agreed In writing, this document Is Ilia dod by the Company subJect to Ita Genoral Conditions of Service printed ovodoaf, avallsbla on request or accessible all hew9/www.aas.cemfprlfT, «!is.nd-Cnndibon�, Attention Is drawn to the Umdallon of liability. IndemnlAcatlon end Jurisdlctlon aeuas defined tharetn Any holds" d Information contained hereon reflects the Company's finding, at the hme of de trde r.enhon only, and wlchm the I:m ds of G.enfs �nahu;.h_- der ;, The Company's aote raaponsibillly Is to Its Cllanl and this document Boas not exonerate parties to a transaction from exercising all their rights and obligations under the IrensacUon docvmenq. This document cannot be rapllhw roduced except In full. wout prior rllten approval of !he Company. Any bneulhortied altarstlon. to gory or felslacallon of the content or appearance of this document Is unlawful and offenders may be pmsatwtad to the fullest extent of the law. Unless otherwise slated the results shown In this test report refer unly to the sample(%) tested and such sampm(s) era retained for 30days adyk Attention 7— thenticity, of tasting llnapectlon report&—tlflwta•pbaee concept us at telephone oramalf: CWV .149910 lid MYlirM4W2fv1nRa651atQu8tat(i�DllhlQoyplgphMttl+ l 9�fA9�aD�MPI402260 tW23)8636760()t www.sgsgroup.com.cr ��p# • iJJ E>zM�A##i#$�Ci24A16$ l BARIM4##f1t8 MIN l 11610: 40M t (8t;-23) 8076DOI sp chlt.com Member of the SGS Group (SOS SA) Project No.: CQES2208000153BA TRF_UL 9540A Unit_V1.0 Page 4 of 40 Table 2: Description of battery module Model: E-BOX-48100R Manufacturer: Shanghai PYTES Energy CO., Ltd. Nominal capacity: 100 Ah Nominal voltage: 51.2 V Module designation: Lithium ions, LiFePO4 Maximum charge current: 100 A Maximum discharge current: 75 A Maximum charge voltage: 58 V Cut-off Voltage: MO 47.5 V EA Charge temperature range: OeC to 450C Discharge temperature range: -10eC to 500C 116111. Unit configuration: 16S External dimensions: 440mm`62'Omm'117mm Enclosure material: Iron Weight: Appr. 51 Kg UL 1973 compliant: ❑ Yes / ❑ No N/A • .ti h. e f Figure 2a. External view of battery module y> 4i �[/• 11•'1-C(t•/�( q seaas�asr. •ry stceesaaa (%Jii Unless otherwl':u :, �rasd In writing, this document Is 11--1 by tha Companl r.,ibjocl to he General Condhlons of Service printed ovedoaf. avallable on request or ecCostlbla al npoa9lwvawsna.men/aRQv(r,r- nd•r_ ditlonj, Altenllon Is drawn to trio Ilmdatlon of Ilablw, Inde11callon end jurls Ilctlon souse ddlnedill Wfk Any holder of 11. vis Informetlon contained hereon reflects the company' t hndings al the hme of rte Intenenhon Doty and wllhm the Lmaa of Cl.ent's !nsulx:bme, d The Company's sole responsibility In to Its Client and this document does not exonerate partlN to a transaction from exerdillng all their rights and obligations andor the transaction docvmente, This document cannot be reproduced except In full, wlthoul prior written approval of the Comparry.Any unauthorized alteration, forgery orfasltkatlon of the content or appearance ofthlsdoeument Is unlawful and offenders may be prosecuted to the fullest extant or the law. Unless otherwise slated the (*suits shown In this last report rotor only to the samples) tested and such L" sampta(at ye retained for 30 days Doty• f + AtbnUon To: thenticlty, ofta Ling llnapecllon report&u. rte•phesa contact ue at telephone .. or small; CH L� 111,99111 SG>G# )U.Ud b ` fYpelKY42WyplNr6ShwW9eKi�tGMKOagprlpMltltEo�1'&ftWgh&svO*P tMa)A6367W www.sgsgroup.00rn.ar 402Z80 14S•iarffi>»I@2T�Iii#r.*i2gAre#ITDEIt�Iff�1t1Y2l�iEr1 AIM: 4IJ2m t(I6O)t1636MI apchireQspoom Member of the SGS Group (SGS SA) Project No.: CQES2208000153BA TRF_UL 9540A Unit_V1.0 Page 5 of 40 Deducted Figure 2c. View 01 of BMS Unloss otherwl :n t read In willing, this document is lit co by th:, Compa n i ..,:b)eet to Its Ganoral Condhlons of Se"Ics printed ovedoat. available on laquest or Accessible at heoa.//Menv.ramlra9fT.:rr, -and-C_netilion.L Attention s dawn to the li-tallon of tleblh�r, IndemnlAcsllcn end Jurisdiction eaves defined therein Any holder of Information contained hereon reflects the Company's finding, al lhv hme of -h rites —h— only end wIih�n the 1—1. of Cl vnt'. ,n.bta b-., it en;, The Company', sole re'pon sibillty Is to Its Cllent and this document does not exonerate parties to a transaction from exercising all their fights and obligations u n,der ill y Iransaodon docv mente. This document cannot be r,produced except In full. without prior wntlen approval of the Company. Any unauthortxedalterallon,forgeryorfaledkationofthecontentorapos ranceofthis documentleunlawful and offenders maybe prosecuted to the to llest extent or the law. Unless otherwise stated the results shown In this test report rarer only to the sample(s) tested and such sample(#) am retained for 30 days orgy Attention Toc s thenttcity of tasting llnapecllon report&cerllrbale•phaae cone,lusattetephone:ie6.755)83071443. Or vmaii: Ct1.0 -94CO10 Lid(pprtrllbirYyppa6Sltwpu9altM�IDM140a�pYllpMltl 4MM t W23)8636i(iOQi www.sggroup.wmcn Ipm • �8 ffiiT>t@A�fii#s*i2gAt6$1 [HFItiAll R1f1#ltM� I 1004: 402200 t W23) 863676001 s93 cNneQsgs.=n Member of the SGS Group (SOS SA) Project No.: CQES2208000153BA TRF_UL 9540A Unit_V1.0 Page 6 of 40 Deducted Unless otherwl so agreed N wrfting. lhls� dr,oel,a,.tm'/aa,�tl.t,s, .h,t�e'uad by the Company oubJect to Its Ganorel Condelons of Service printed ovorloaf. evNleble on request or Accessible eilrt•1CfL�-:nd-r'4*.Al11onL Attention Is dawn to the timilatlon of Ib01w, Indemilflcatlon and Jurlsdlctlon asues detaMO nafsltt. Any holder of Information contained hereon reflects the Company's finding. el the lime of Its Intetven6on only end wllhm the L.A. of 01 .T.—U—Jtio^s, d any. The Compeer/s sole respon siblllty is to Its Client and lots document does not exonerate portion to a trenseetlon from exerclNng all their tights and cellgallorts under ir. a Ifnnaa Won documents. This document cannot be reproduced except In full, wlihoul pilot wnllen approval or the Company. Any unauthorized alteretlon, torgery, or felstftcallon of the content or appearance of this document Is unlawful and offenders may be prosecuted to the fullest extent or the law. Unless otherwise stated the results shown In this test report rater unly to the sample($) tested and such sempN(a) ere retalned for 30 days orgy Attention Toc A nVulty of lasting llnapeclton report&csrilflcale,pl—e contact us al telephone: le6.755)83071443. or small: Ctf.O �y4CelA Lid aprtr0.lblwpna ashw�u9etti¢luwt0av0�aphl�l re�atlsa�9�eD�AI oa71®o t 0-086361W wwaragsgmup.com.0 �$# • 18�t6tTit�A####siCi24A16$ I t ItiAt##R1tt> #r 1 MM: 4oz2e0 t (66-23) 8IW76M1 ags.c tirre".cdrn Member of the SGS Group (SGS SA) Project No.: CQES2208000153BA TRF_UL 9540A Unit_V1.0 Page 7 of 40 Table 3: Description of battery unit Model: R-Bracket Manufacturer: Shanghai PYTES Energy CO., Ltd. Nominal capacity: 100 Ah x 8 Nominal voltage: 51.2 V Module designation: Lithium ions, LiFePO4 Maximum charge vo tage: 58 V Cut-off Vni� 47.5 V Charge temperature range: O°C to 45°C Discharge temperature range: -10'C to 50'C Unit configuration• 8P External dimensions: 525mm"725mm'1080mm Enclosure material: Iron Fire suppression system contain ❑ Yes / [21 No Reference: N/A UL 1973 compliant: ❑ Yes / ❑ No Reference: N/A UL 9540 compliant: ❑ Yes / [:]No Reference: N/A Unless otherwb:oagreed In writing. thisdocument Is lua dad by the Compenv> bjact to ha Genoral Condhlons of Service prinled ovadosf. avellable on request or accessible al MIos9lwww.frv.tomfpr1lT,rme-•nd- _ divoriL Attention Is drawn to the bmdatbn of 301W,. Indemnlflcellon and judedldlon sauee dafMsd Ihanln Any holder of Information contained hereon reflects the Company's findings at the lime of rls hrle r�enhrin only end wI hen the 1— 1s of Cl.ent's—t—tiu^s, d any. The Cumpenv's who respon sibillty la to Ita Cllent and this document does not exonerate perllas to ■ transaction from exerclsing all their tights and obligations a ndor th a Irensacpon dxuments, Thls document cannot be sproduced except In full, without prior wrttten approval or the Company. Any unauthorlZed elteratlon, forgery or falsification of me content or appearance of this document Is unlawful end offenders maybe prosecuted to the fullest extent or the law. Unless otherwise stshsd the results shown In Nis lost report rarer unly to the sample(s) tested and such sempN(s) are retained lot 30 drip ordy Attentlor ,thenticlty of lasting flnapectloa reports car11f1ute,pMaw contact us at telephone or email :94c910 Ud NYlrte4NelrMnita6SlnP SMb�IQIYtll3oVit5ptiM11t �I �Gd9�aD�PI 402260 1(�- 1863676001 www.sgegroup.=rxrr ��S•i6�ffi @IIi�tt#xjCi12#Are#IIIDFIt�AIff#It111 II1Er1 111I0:4MM t(e6-Z)O6361 I ags.dl:mm Member of the SGS Group (SOS SA) Project No.: CQES2208000153BA TRF_UL 9540A Unit_V1.0 Page 8 of 40 s S u � i � r o fffr Pyt S a P s i i -14 p it Figure 3a. View 01 of battery unit Unless otherwise agreed In writing, this document is Issued by the Company subject to As General Conditions of Service printed owdeaf. available on isquesl or accessible al httpsd/www.sas.wm/ertRerms-end-Condihons. Attention a drawn to the itmdation of liability, I ,I. Indemnfflcellon and Jurladldlon Issues defined therein Any holder of this document Is advised that Information contained hereon reflects the Company's findings at the time of Its Intervention only and within the imps of Client's Ina uctlons. If any The Company's We i%. responsibility is to Its Client and this document does rot exonerate parties to a transaction from exercising all their rights and obligation$ under the lrarearto, documents, This document to nnot be reproduced except In full. without prior written approval of the Company. Any -c� unauthorized alteration, forgery or falsification of the content or appearance of this document Is unlawful and offenders may be prosecuted r`• ''14J i; (:; r, to the fullest extent of the law. Unless otherwise stated the results shown In this test report refer only r to the sans s) tested and such Is p ( holden s"Semon '; samplo(s) are retained for 30 days only. Attentlon To chat$ the authenticity of testing rnspection report & certificate, pies.. contacl us at te(ephone.ieo-7ss)e?o' 1447. a omoll'. C►f,Q99ChgCl1M1�$IIs$,,.9y9m �,,r,, �aa .y .i,l ..,:11MMrb.B.fbiflafbb,..�Yyy��T�p��f��'y�a�ajp��+`Wtl�� ipnrw)�%�i WNW.$Q$gf9tN1.p01fl.fll <�mr I�t®.�fft3Si1t3Ai�6i11ona.5M66�,(S9F16rss-{etri�lllErl 16M:402260 1(8f>-?)SM67M sps.danar&pacom Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 9 of 40 !MM Unless otherwise agreed In writ rig, this document is Issued by the Company subject to Is General Conditions of Sarvke printed overleaf. p! �' 07 available on request w accessible at hltoaa/wwwsaa.cam/anRerms-end-Condibiona. Attention Is drawn to the limitation of liability, •1,1• '7 x Indemniflcalmn and Jurisdiction Issues defined therein Any holds of this daament b advised that intormetbn cantsmad hereon reflects the Company's findings at the time of Its intervention only and within the limils of C6enra InsWWona. if any The Company's sob r%. responsibility is to Its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the tram ectbn documents. This document cannot be reproduced except In full. without prior written approval of the Company. Any w unauthorized alteratbn. lorgery, or falslficetbn of the oontent or appearance of this document is unlawful and onanders may be prosecuted r`• ''14J 1. (:; r, ^axto the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only r to the sample(s) tested and such ynss�el{TetMtgSemtn'; sample( re Tocsined 1600 titIheautheys only ticIty Attantlon To chats the suthenticlty of testing rimpacpon nporta cartifiuu, please contact us ah hslepn on,.isa-755j 03a'1443. a small'. C"'Docchoc MilksIIe.oarn MYhfb4lb]hM�4 tJY jtOiYttObpl4 f�l� i ^B fdO�B�Ph 4OZ260 t 86387W www.sMrotp.owen �® f& �i1�Ait6yiAak M6# I t9F16i�t�gRta lliErt i 1a11: aul M t "WISMO na�amih Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 10 of 40 FMA [Description of thermal runaway methodology] Sample and test configuration The unit level test shall be conducted with BESS (Battery Energy Storage System) units installed as described in the manufacturer's instructions and this section. The unit level test requires one initiating BESS unit in which an internal fire condition in accordance with the module level test is initiated and target adjacent BESS units representative of an installation. Tests conducted for indoor floor mounted installations shall be considered representative of both indoor floor mounted and outdoor ground mounted installations with fire propagation hazards and separation distances between initiating and target units representative of the installation- Tests shall be conducted indoors with fire propagation hazards and separation distances between initiating and target units representative of the installation. The results of such tests shall be considered to also represent an outdoor installation. Depending upon the configuration and design of the BESS (e.g. the BESS is composed of multiple separate parts within separate enclosures), this testing to determine fire characterization can be done at the battery system level. The suitability of this approach shall be determined based upon the overall design of the BESS and an analysis of the battery system as representative of the overall BESS for fire characterization concerns. The initiating BESS unit shall contain components representative of a BESS unit in a complete installation. Combustible components that interconnect the initiating and target BESS units shall be included. Target BESS units shall include the outer cabinet (if part of the design), racking. module enclosures, and components that retain cells components. The target BESS unit module enclosures do not need to contain cells. The initiating BESS unit shall be at the maximum operating state of charge (MOSOC), in accordance with the manufacturer's specifications, for conducting the tests in this standard. After charging and prior to testing. the initiating BESS shall rest for a maximum period of 8 h at room ambient. If a BESS unit includes an integral fire suppression system, there is an option of providing this with the DUT. If the BESS unit is provided with an optional integral fire suppression system, the system shall not be provided on the DUT- Electronics and software controls such as the battery management system (BMS) in the BESS are not relied upon for this testing. This does not include a fire suppression control in accordance with UL 840 that is external to the BESS, but provided as part of an integral fire suppression system. Table 4: Integral fire suppression system information Integral fire suppression system information No integral fire suppression system Standard or optional ❑ Standard / ❑ optional / 0 NIA Test with fire suppression or not ❑ Yes / ❑ No Unless otherwise agread In wnt.ng, this document is Issued by the Company sublact io its General Conditions of So"" printed overleaf. available on request or accessible at hltoa:llwwwsaa.wm(enlTerms-ard-Conditions. A9enbon Is drawn to the limitation of liability, w, il• % xx�� Indemniflcatlon and Jurbtlktlon sauas dellnod therein Any holder of this document Is advised that Information contained hereon reflects •yam the Company's findings at the time of Its InlemenUon only and within the limits of Client's Instructions. II any The Company's sob r�_ responsibility Is to Its Client and this document does not exonerate parties to a transaction from exerclOng all their rights and obligations under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or telsitication of the oontent or appearance of this document Is unlawful and offenders may be prosecuted I:;,.- to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such wnn6g11TtsfYgSemce _; sample(s)sreretainedlOY30daysonl Attention To check the authenticity of testing r Inspection report A certificate• please conl-i - !elephona-I8a-755)03071447. a omal l'. (, ff,Q99ChgCl11f 0IIa.99m _J 111etb.4lb]r�ullb4�r�r ttilrlOiYtt(�sY14a++f�l�+ it ^B. {dto�B' h 4OZ260 f P")86387M wodits ialp.lwm.on �® 1& �i1�Ai16�iAsk M6# I t9 8XV#WfJ"d) JW: 402260 t Wa--n)86367M agfsxhin8@9pzpm Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 11 of 40 Table 5: BESS installations/ Test configurations Description: ❑ a) Indoor floor mounted non-residential use BESS b) Indoor floor mounted residential use BESS ❑ c) Outdoor ground mounted non-residential use BESS ❑ d) Outdoor ground mounted residential use BESS ❑ e) Indoor wall mounted non-residential use BESS ❑ f) Indoor wall mounted residential use BESS ❑ g) Outdoor wall mounted non-residential use BESS ❑ h) Outdoor wall mounted residential use BESS ❑ i j Rooftop garage non-residential use BESS ❑ j) Open garage non-residential use BESS Test configurations for Indoor floor mounted residential use BESS Instrimented Front A 50 mm Wa I Section B 50 mm a} m C 50 mm nittatng BESS p Targe: BESS Uni Unit initiating unit target unit 2 D 0 mm E 0 mm L `v O F 0mm G 50 mm yG Target BESS H Target BESS Jni- Unit target unit 1 target unit 3 H 0 nvn Front Unless otherwise agreed in wnt rig, this document is issued by the Company subject to Is General Conditlons of Service printed ovedes 1. available on isquesl or accessible at httoaarwww.sos.comien/Tgrms-end-Condl6ons. Attention is drawn to the limitation of liability, x� Indemnificallon and jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reflects •yC� the Company's Gndlr?s at the time of 115 Inlervendon only and within the limits of Clients InstruWons. d any. The Company's sob r� responsibi le to Its Cnent entl this document does not exonerate parties to a transaction from exercising all their rights end obligation ' - under the transaction documents. This document cannot be reproduced except In full. without prior written approval of the Company Any unauthorized alteration, !orgery or talsrticatlon of the courant a appearance of this document is uniawful and offenders may be prosecuted i. I: , to the fullest extent of the low. Unless otherwise stated the results shown in this lest report refer only to the sample(s) tested and such NSIs6e11Te�YtgSemce sample(s)amretained for30days only . A Uentlon To theca t he authentic lty of testing nn s pecu on r ep art A certiflut&. pi es se c orila 0 s tel a ph on a"1f16-755)Vol 144 i. or email. CN.0vcchgc hl�sas.avm _ 1 AlYhlb.4lb]hM�4 tilrtOMitNlay¢4dhf�f�' 1 & {d4�' 1 40M t (W23)86387M www.sMfouip.com.rn I1110-UrUN9- MMU240KIOWN:402260 tWz,-zi1863UM Wctinel@sgacm Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 12 of 40 FMA Unit level Test method description Test method — Indoor floor mounted BESS units Samples and test configurations are in accordance with Table 5. During the test. the test room environment shall be controlled to prevent drafts that may affect test results. At the start of the test. the room ambient temperature shall not be less than 10"C (50"1`) nor more than 32°C (90-F). Any access door(s) or panels on the initiating BESS unit and adjacent target BESS units shall be closed. latched and locked at the beginning and duration of the test. The initiating BESS unit shall be positioned adjacent to two instrumented wall sections. Instrumented wall sections shall extend not less than 1.6 ft (0.49 m) horizontally beyond the exterior of the target BESS units. The surface of the instrumented wall sections shall be covered with 16-mm (5/8-in) gypsum wall board and painted flat black.The initiating BESS unit shall be centered underneath an appropriately sized smoke collection hood of an oxygen consumption calorimeter. The light transmission in the calorimeter's exhaust duct shall be measured using a white light source and photo detector for the duration of the test, and the smoke release rate shall be calculated. The chemical and convective heat release rates shall be measured for the duration of the test. The heat release rate measurement system shall be calibrated using an atomized heptane diffusion burner. The calibration shall be performed using flows of 3.8, 7.6, 11.4 and 15.2 Umin (1, 2, 3 and 4 gpm) of heptane. The convective heat release rate shall be measured using thermopile, a velocity probe, and a Type K thermocouple. located in the exhaust system of the exhaust duct. the convective heat release rate shall be calculated using the following equation: 4L.—- T HRR, = VIA 35-�,c17 a To The physical spacing between BESS units (both initiating and target) and adjacent walls shall be representative of the intended installation. Separation distances shall be specified by the manufacturer for distance betr`reen: a) The BESS units and the instrumented wall sections; and b) Adjacent BESS units. Wall surface temperature measurements shall be collected for BESS intended for installation in locations with combustible construction. If the intended installation is composed completely of noncombustible construction in which wall assemblies, cables. wiring and any other combustible materials are not to be present in the BESS installation, then the report should note that the installation shall contain no combustible construction and that surface temperature rises can be deemed not applicable. Wall surface temperatures shall be measured in vertical array(s) at 152-mm (6-in) intervals for the full height of the instrumented wall sections using No. 24-gauge or smaller. Type-K exposed junction thermocouples. The thermocouples for measuring the temperature on wall surfaces shall be horizontally positioned in the wall locations anticipated to receive the greatest thermal exposure from the initiating BESS unit. unless otherwisa agreed In wril•ng, this document is Issued by the Company sunjoct ro Its General Conditwns of Service pr: nted overleaf, availetNe On request or accessible at httos'rwww.y,�.com/en/Terra-erw]-(:ondd�ona Attention is drawn to the limitation of liability, Indemnification and Jurisdiction issues defined therein Any holder of Ihla document K advlsed that Information contained hereon reflects the Company's findings at the tree of Its Intervention only and within the limits of Client's Instructions, if any. The Company's sots respnnsiNilly is to Its Client and this document ones rot exonerate parties to a transaction from exercising all their rights and obllgatlnns under the nanseollon documents. This document cannot be reproduced except In full. without prior wniten approval of the Company Anv unauthorized alteration, !orgery or falsification of the content or appearance of this document �s unlawful and offenders may be proserutea I to the fullest extent of the law. Unless otherwise stated the results shown in this lest report rotor only to the sample(s) tested and such -,x_V,S 7r5tn„3,,:ee sample(s)areretalnedfdr30daysonly. AOention To chece the authenticity of testing onepection report A certificate. please c riiaa 5 .elepn ona.IBa-75+I eJe'tJa :. _ or omau. CN.CvcchvcMl�eas.avm IMYhNtD,lb]FeMNa4Shalye�MlilrlOiYttNlay¢4dhf��' it ^B. fd4�B' ! 40M t (llti-23)88387M www.6MfoLIp.dom.m N®i&�Si1�Ai�6yiA$�cl aM6$It&16i�1 1f ltMEri OW:402280 tWErM)883678Wt Wctine@sgacom Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 13 of 40 M I Thermocouples shall be secured to gypsum surfaces by the use of staples placed over the insulated portion of the wires. The thermocouple tip shall be depressed into the gypsum so as to be flush with the gypsum surface at the point of measurement and held in thermal contact with the surface at that point by the use of pressure -sensitive paper tape. Heat flux shall be measured with the sensing element of at least two water-cooled Schmidt-Boelter gauges at the surface of each instrumented wall: a) Both are collinear with the vertical thermocouple array; b) One is positioned at the elevation estimated to receive the greatest heat flux due to the thermal runaway of the initiating module: and c) One is positioned at the elevation estimated to receive the greatest heat flux during potential propagation of thermal runaway within the initiating BESS unit. Heat flux shall be measured with the sensing element of at least two water-cooled Schmidt- Boelter gauges at the surface of each adjacent target BESS unit that faces the initiating BESS unit: a) One is positioned at the elevation estimated to receive the greatest heat flux due to the thermal runaway of the initiating module within the initiating BESS: and b) One is positioned at the elevation estimated to receive the greatest surface heat flux due to the thermal runaway of the initiating BESS. For non-residential use BESS, heat flux shall be measured ,vith the sensing element of at least one water- cooled Schmidt-Boelter gauge positioned at the mid height of the initiating unit in the center of the accessible means of egress. No. 24-gauge or smaller. Type-K exposed junction thermocouples shall be installed to measure the temperature of the surface proximate to the cells and between the cells and exposed face of the initiating module. Each non -initiating module enclosure within the initiating BESS unit shall be instrumented with at least one No. 24-gauge or smaller Type-K thermocouple(s) to provide data to monitor the thermal conditions within non -initiating modules. Additional thermocouples shall be placed to account for convoluted enclosure interior geometries. For residential use BESS, the DUT shall be covered with a single layer of cheese cloth ignition indicator. The cheesecloth shall be untreated cotton cloth running 26 — 28 m2/kg with a count of 28 — 32 threads in either direction within a 6.45 cm2 (1 in2) area. An internal fire condition in accordance with the module level test shall be created within a single module in the initiating BESS unit: a) The position of the module shall be selected to present the greatest thermal exposure to adjacent modules (e.g. above, below, laterally), based on the results from the module level test: and b) The setup (i.e. type. quantity and positioning) of equipment for initiating thermal runaway in the module shall be the same as that used to initiate and propagate thermal runaway within the module level test. Thermal runaway methodology for unit level test: The propensity of the cell to exhibit thermal runaway be demonstrated by heating the cell with externally applied heaters. With a surface heating rate of 4°C (7.2°F) to 7°C (12.6°F) per minute until cell thermal runa.vay occurs within the test unit. The composition, velocity and temperature of the initiating BESS unit vent gases shall be measured within the calorimeter's exhaust duct. Gas composition shall be measured using a Fourier -Transform Infrared Spectrometer with a minimum resolution of 1 cm-' and a path length of at least 2.0 m(6.6 ft), or equivalent gas analyzer. Composition, velocity and temperature instrumentation shall be collocated with heat release rate calorimetry instrumentation. The hydrocarbon content of the vent gas shall be measured using flame ionization detection. The test shall be terminated if: Unless othorwlso agreed In cant, ngthis document is Issued by the Company subject to Its General Condit ions oIS a rvice Canted overleaf, available on request or accessible at httos'rwwwsda.comlenlTerma-erd-Cor+dibona Attention Is drawn to the limdat- of liability. Indemnification and Jurlsdldlon Issues defined therein Any holder of This document is advised that Information contained hereon reflects The CamDeny'a f�ndings at the time of 116 Intervention only and within tits hmlla of Client's InsbUGilona, II any. The ComDeny's sole Tarpons Hilly Is to Iis CRent and Iris doculnam does not exonerate parties to a Transaction from exercising all MPIr rights, end obllgallone under the bensaolbn documents. TMm s document cannot be reproduced except In full. without prior written approval of The Company Any unauthorized alteration, forgery or taleiecatbn of the content or appearance of this document Is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this lest report refer only to the sample(s) tested and such semplili are retained for 30 days only. Attention To checa the authentic I" of testing rInspection report A certifrc al pieM so contact s teleph one. lBO-7551530' I44 i. or small . CN,�aCChltCh�afla.COm IAiYhNt41b2i,M�4 tM�tDiYltRny¢gl7hftilhimMl 4 ffi9 API 40M 1 (W23)86381M—spagroup.cdm.rn N® iff�Sil�Ai�6yiA3�tl aMB$1=6F16i�1 1f�rltMErl 16M: 402M t 0-M063671 Wt age-dunaiftspcom Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 14 of 40 a) Temperatures measured inside each module within the initiating BESS unit return to ambient temperature-, b) The fire propagates to adjacent units or to adjacent walls; or c) A condition hazardous to test staff or the test facility requires mitigation. For residential use systems, the gas collection data gathered shall be compared to the smallest room installation specified by the manufacturer to determine if the flammable gas collected exceeds 25% LFL in air. Unless otherwise agreed in writing, this document is issued by the Company subject to Its General Conditions or Service printed ovodeaf, il• pt �' ( CT available on ret)uesl w accessible at httoa.ttwww.sos.comien/Tgrms-and-Conditons. Attention Is drawn to the limitation of liability, xInd emnificallon and jurisdiction Issues defined therein Any holder of this document Is advised that Information contained hereon reflects •yC� the Company's rndir?s at the time of Its Intervention only and within the limits of Clients metruWons, d any. The Company's sob r� responslMlfry Is to Its Rant and this document does rot exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except In full. without prior written approve of the Company Any a - unauthorized alteration,!orgery or fiter6catlon of the content or appearance of this document is umawful and offenders maybe prosecuted I: - to the fullest extent of the low. Unless otherwise stated the results shown in this lest report refer only to the sample(s) tested and such ynn6atlTlslYgSemtes sample(s)areretained for 30daysonly . Altentlon To chece t he authentic lty of testing nn s pecti on r sp art A certiflut&. pi ea se contact s= tel a p h one"106-755)53011443 or email. CN.Cvcchvchl�eas.avm _ l AlYhrb.4lb]hM�4 t�lOiYttNlay¢4dhf�f�' I B. {d4�' 1 40M t (W23)86387M www.apsgroup.lwm.rn th® 1ff7Sil�Ai�6 �iASk aMB$1=6F16i�l ltlf�rltMEr l OW: 402280 t 0-231883PM age cfina@sp com Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 15 of 40 Test configuration description Description: NIA Illustration of the initiating BESS unit -_W r Fiaure 4. View of the initiatina BESS unit before test. FMA Unless otherwise agreed In writing, this document is issued by the Company subject co its General Conditions of So"" printed overlaef. available on request or accessible at httoaarwww.sus.com/antTe"s-and-Condit,ma, Attenbon is drawn to the limitation of liability, xx Indemnfflcsflon and Jurisdiction issues defined theroin Any holder of this document Is advised that Information contained hereon reflects 0 Y` the Company's Gndlngis at the time of Ile Intervention only and within the limits of Clients Instructions.'Iany The Company's sob _ responalb liry Is to Its Client and this document does rot exonerate parties to a transaction from axerclOng all their rights and obligations under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or fatsihoatbn of the oontent or appearance of this document is unlawful and offenders may be prosecuted I:;,.- to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such Yan6enlTtsMe)Semtee '; sample(s) are retained for 30 days only Attention To chathe authenticitts of testing r Inspection report A certificate, piease conks .= Ialepnons.l9s-75+j 0?a'tddi. ar small'. CN,Qocchocklitf IIss..dydrn :'I Nr.�Ib.B.(bifR�lxpya(rvivseee..y��arY�yyyy(��,.{T,�ppaaQ��I�� I��M6ee�1�L y.aa/p IQla�y+`eWtl`f�yQ 4� tr(pa�486319 i wwW.sMroup.comen I T®' r>•Tr+allle�le Y/�lKSmaS ( UNN {es NAIMINl OW: 4� t Wa-- I8. %M %PxNna@SP=m Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 16 of 40 Thermal runaway initiation method used (including number and locations of cells for initiating thermal runaway) Initiation method: External heating method was used to initiate thermal runaway. 2 heaters were used to initiate thermal runaway. Heater 1 was placed between the large surfaces of Cell 2 and Cell 3. Heater 2 was placed between the large surfaces of Cell 3 and Cell 4. Cell 3 was selected as initiating cell. Each heater was connected to one voltage regulator. Heater 1 and Heater 2 were energized at the same tin -le. The working currents of Heater 1 and Heater 2 were continuously adjusted to make sure that the initiating cell was heated at a ramp of 4-7 eC/min. Number of cells for initiating thermal runaway: ® Single cell 100 Ah (total capacity) ❑ Multiple cell Ah (total capacity) Locations of cells for initiating thermal runaway: The initiating battery module consi sts o(,2 subm, cdules. Each submodule consists of 8 cells with a connection mode of 8S. Two submodules are connected in series. One 8S submodule (as shown in Figure 5c) is selected as the initiating submodule. heaters were placed orl large face of cell 3. Cell 3 is selected as the initiating cell_ Other description: N/A r .er.. Figure 5a. External view of ba module. Figure 5b. Internal schematic view of battery module. r - i Figure 5c. Internal view 03 of battery module. Figure 5d. View of heater. Unless otherwi ::u mead In writing. this document k lots uedby the Comps n y a bJect to its Genoral Condltlons of ServJoe printed overl"l. ■rallable on request or accessible at haoslrwww.arv.mml arn5rrnr_-end-rnndillon_L Attention Is drawn to the limitation of tlabll 'r Indsmsi0csllon end jurlsolctlon saues d@Ansd tharaln Any holder of InPormetlon mndlned hereon rehacis the Company's find[ ngs bt the Uma of 14 rntvroentlun only and wdN:, the L�m1a of CLcnlb mabucuuny, d e This C. orpeny's sots reaponadtlllty le to its (lion l and this document dose not exonerate perdu to a banaaetlon hen a:erdtdrq ell their rights and ob Ibatlona under the transaction documents, This documonl cannot be reproduced except In full, whhoul pdorwrittsn approval of the Company. Any unoutnorized alteration, forgery or falamcalldn 01 the content or ep tearence of thle document Is unlewtul and 0lfendera may 00 prosecuted to the fullest extent of the law. Unless otherwise stated the results shown In this last report rarer only to the sample(e) lasted and such @ampp(8 ere rIt tried for 30 days CW Attention 7o check : t henticl y of t as lino tin a pact[ on report a cortlOwN, please I telaphons: le0.755)83071443. oremad7 CTld/lxth_. gadeID I, INaereaw:WplardBM¢s>rcrrfapowta�riphta�bmt+eretllaa.Ill91*Up)4eo ((e6-231e63sr i wma.snioup.cosi COS' 201TMIIIsi( f,*i21l ( I IUMU 611IIiis 1 AfM: 40t M t N-?3 00760M sw.d**@gp m1 Member of the SGS Group (SGS SA) Project No.: CQES2208000153BA TRi UL 9540A Unit_V1.0 Page 17 of 40 Illustration of external heater and thermocouple location Description: N/A T1 A T11 T2 T3 T10 T4 Figure 6a. Schematic diagram of initiating module. CELL 1 LL SELL 2 IF CELL SELL 3 CELL 4 CELL 6 CELL 5 Heater 2 T8 B T7 Heater 1 kid T5 T13 Figure 6b. Schematic diagram of external heater and thermocouple locations in the initiating module (Side view). Unless otherwise agreed In writing, this document is issuad by the Company subject to As General Conditions of So"" printed overleaf. available on request or accessible at hltoa:llwwwsoa.Coco/enlTerma-erd-Conditions. Attention is drawn to the limitation of liability, xx�� Indemnification and jurisdiction issues defined theroin Any holder of this d9cumant la advised that Information contained hereon reflects .1.� •:5 the Company's findings at the time of Ile Intervention only and within the limits of Clients Instructions. if any The Company's sob r�_ responslbiliry Is to Its Client and this document does not exonerate parties to a transaction from exerclOng all their rights and obligations under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders maybe prosecuted to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such ,rz �T�ymlp sampla(s) are retained for 30 days only. Attention To checs the authenticity of testing i inspection report a certificate• please contact ,=- telephone. 104-755) 630' 1443. 9r enroll. (, ►f,Q99ChgCllMi�tIIsa,,.9y91n a� ��r.,, r�,,i,, (�a...� �aa y� wwM.sMitilip.com.on I�®•i&7�11f3Aii6�iAaJc1'rt$M6�(T��aiai-{esii�'r�Er) �:407180 f(tlf>^?3)883676001 s9g-d�na�ega'can Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 18 of 40 Positioning of units within testing room Test Start Time: 2022-08-09 14:42:00 Initial Ambient Test Temperature: 28.8 IIC Initial Relative Humidity: 58% Description: NIA (initiating uii) Unit B (tar u t, ..,(target unit 1} nit D target unit 3) 1 '• a 1 % e Figure 7. View of BESS within test room. Unless otherwise spread In w,il•ng, this document Is Issued by the Company subject to da General Conditions of Seraice prinked overleaf. availebte M request or accessible at hnoaarw+wwsaa.camjanRerms-end-Candklma. Attention Is drawn to the limitation of liability, Indemnification and Jurladlctlon Issues defined therein Any holder of this document Is advised that Information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Client's instructions. if any The Company's sob responsibility is to Its Client and this document does not exonerate parties to a traneactlon from axercisfng all their rights and obligations under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be proseraned to the fullest extant of the law. Unless otherwise staled the results shown in this tent report refer only to the sample(s) tested and such rssel6Os 6 ie q kn¢o q sampla(s) are retained for 3o days only. _ Attention To check the authenticity of testing inspection report A certificate, pieces contacl us at tsiephons.lea-7ssja3o'1441. _ or small'. C►f,QgiChgC Mi�OIIa.Cgln :) AlYhfb4lb]hM�4��tJYlrtOiYtt(�sY14�kl�t�'�J�&�{diO�B'�Ph 4D?Z60 t (8�23)88387A001 www.agagrotp.ixm.m I�®•f&��i1�Ait6�iAak�M6#It9F16i�t�gRta�lliE�i 116M: aua�eo tier,-�lee�a�art �ha��«n Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 19 of 40 Table 6: Thermocouple placement Thermocouple ID Description of location Remark CH2501 Side surface A of Cell 1 T1, in initiating module CH2502 Side surface A of Cell 2 T2, in initiating module CH2503 Side surface A of Cell 3 T3, in initiating module CH2504 Side surface A of Cell 4 T4. in initiating module CH2505 Side surface B of Cell 5 T5, in initiating module CH2506 Side surface B of Cell 6 T6, in initiating module CH2507 Side surface B of Cell 7 T7, in initiating module CH2508 Side surface B of Cell 8 T8, in initiating module CH2509 Large surface of cell 3. between cell surface and Heater 1 T9, in initiating module CH2510 Large surface of cell 3. between cell surface and Heater 2 T10, in initiating module CH3001 Bottom surface of cell 2 T11. in initiating module CH3002 Bottom surface of cell 3 T12. in initiating module CH3003 Bottom surface of cell 4 T13. in initiating module CH2O01 No. 1 of wall B WB-1 CH2O02 No. 2 of wall B WB-2 CH2O03 No. 3 of wall B WB-3 CH2O04 No. 4 of wall B WB-4 CH2O05 No. 5 of wall B W B-5 CH2O06 No. 6 of wall B W B-6 CH2O07 No. 7 of wall B W B-7 CH2O08 No. 8 of wall B W B-8 CH2O09 No. 9 of wall B W B-9 CH2010 No. 10 of wall B WB-10 CH2101 No. 11 of wall B WB-1 1 CH2102 No. 12 of wall B WB-12 CH2103 No. 13 of wall B WB-13 CH2104 No. 14 of wall B WB-14 CH2105 No. 15 of wall B WB-15 CH2106 No. 16 of wall B WB-16 CH2107 No. 17 of wall B WB-17 CH2108 No. 18 of wall B WB-18 Unless othorwiso spread In wnt.ng, this document i5 1s5ued by the Company subJact co its General Conditions of Service prmtod ovarlest, available on request or accessible at httoa lrwww.}gs.rmmlenfTerma-end-Cantliuons Attention :a drawn to the limitation of liability, Indemnification and jurisdiction issues defined therein Any holds of thb document b advised that Information contained hereon reflects the Company's findings at the time of Its intervention only and within the hmas of Client'a instructions, if any. The Company's sob responsiblary Is to Its Client and this document does rot exonerate parties to a transaction from exercising all their rights and obligations under the bansaction documents. This document cannot be reproduced except In full. without prior written approval of 01e Company Any unaulhorized alteration, !orgery or tatslficatlon of the rnntent or appearance of this document is untawful and onendere may be prosanned 1 to the fullest extent of the law. Unless otherwise stated the results shown in this lest report refer only to the sample(s) tested end such Initiation S Tests; Scv.ces r sample(s) ere retained for 30 days only. Attention To check t he authentic lty of testing nn a pecu on rap oft A oilifluv, pi as se contact s= tel e p h on e. I06-755)Vol 144 i. _ or omau. CN.CvcchgcMl�eas.avm 1 AlYhfb.4lb]hM�4 tla�sOMitNlay¢4dhf�t�' 1 & {d4�B' 1 4M= t (W23)86387M www.sMfOLIp.cgm.rn Ili® i&�Si1�Ai�6 ♦iA$�ct aM6$ I t&16i�1 1f�rltME(r i OW: 40225D t 0-23OVIRM aeg c ins@sgs can Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 20 of 40 CH2109 No. 19 of wall B WB-19 CH2110 No. 20 of wall B WB-20 CH2201 No. 21 of wall B WB-21 CH2202 No. 22 of wall B WB-22 CH2203 No. 23 of wall B WB-23 CH2204 No. 24 of wall B WB-24 CH1001 No. 25 of wall B WB-25 CH1002 No. 26 of wall B WB-26 CH1003 No. 27 of wall B WB-27 CH1004 No. 28 of wall B WB-28 CH1005 No. 29 of wall B WB-29 CH1006 No. 30 of wall B WB-30 CH1007 No. 31 of wall B WB-31 CH1008 No. 32 of wall B WB-32 CH1009 No. 33 of wall B WB-33 CH1010 No. 34 of wall B WB-34 CH1101 No. 35 of wall B WB-35 CH1102 No. 36 of wall B WB-36 CH1103 No. 37 of wall 6 WB-37 CH1104 No. 38 of wall B WB-38 CH1105 No. 39 of wall B WB-39 CH1106 No. 40 of wall B WB-40 CH1107 No. 41 of wall B WB-41 CH1108 No. 42 of wall B WB-42 CH1201 No. 43 of wall B WB-43 CH1202 No. 44ofwall B WB-44 CH1203 No. 45 of wall B WB-45 CH1204 No. 46 of wall B WB-46 CH1205 No_ 47 of wall B WB-47 CH1206 No. 48 of wall B WB-48 CH1207 No. 49 of wall B WB-49 CH1208 No. 50 of wall B WB-50 Unless odto�mso agreed In writing, this document is Is5ued by the Company subject to 49 General Conditions of Service prmad overleaf, available on request or --lble at hltw irwww.}gs.comlenfTerma-erd-Candlbooa Attenbon la drawn to the I—hition of liability, Indemnification and Jurisdiction issues defined therein Any holds of thb document Is advised that Information contained hereon reflects the Company's rndi at the time of Its intervention only and within the limits of Client's InstrucJons, if any The Company's sob responalbmry Is to Its C,onl and this document 6006 not exonerate parties to a transaction from exercising all their rights and obligations under the bansaclion documenls. This document cannot be reproduced except In full. without prior written epproval of I1ro Company Any unauthorized alteration, !orgery or talilficatbn of the content or appearance of this document is unlawful and ohenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this lest report refer only to the sample(s) tested and such a! sample(s)areretsined for 30 days only. A ttenllon To checa l he authentic lty of testing i l n s pecu on r ap ort A ortiflut*, pi ea se contact s tel e is h on a. I06-755)53011443 or omtdf. CII.CvcchocMlllksaa.cam IAlYhfb4lb]hM�4 tdrtOiYttDO9¢4dhf�� 1 ^B {d4� 1 40M 1 (W23)86387M www.6gagroup.0on.rn lia® iff�Sil�Ai�6 ♦iAS1c1 aM8$1=6F16i>w1 lf�rltMEr l OW: 402260 t Wz-M)863U= age cNnaf@s coin Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 21 of 40 CH1209 No. 51 of wall B WB-51 CH1210 No. 52 of wall B WB-52 CH1301 No. 53 of wall B WB-52 CH1302 No. 54 of wall B WB-54 CH0001 No. 1 of wall A WA-1 CH0002 No. 2 of wall A WA-2 CH0003 No. 3 of wall A WA-3 CH0004 No. 4 of wall A WA-4 CH0005 No. 5 of wall A WA-5 CH0006 No. 6 of wall A WA-6 CH0007 No. 7 of wall A WA-7 CH0009 No. 8 of wall A WA-8 CH0010 No. 9 of wall A WA-9 CH0101 No. 10 of wall A WA-10 CH0103 No. 11 of wall A WA-11 CH0104 No. 12 of wall A WA-12 CH0105 No. 13 of wall A WA-13 CH0106 No. 14 of wall A WA-14 CH0107 No. 15 of wall A WA-15 CH0108 No. 16 of wall A WA-16 CH0109 No. 17 of wall A WA-17 CH0110 No. 18 of wall A WA-18 CH0201 No. 19 of wall A WA-19 CH0202 No. 20 of wall A WA-20 CH0203 No. 21 of wall A WA-21 CH0204 No. 22 of wall A WA-22 CH2205 No. 23 of wall A WA-23 CH2206 No. 24 of wall A WA-24 CH2207 No_ 25 of wall A WA-25 CH2208 No. 26 of wall A WA-26 CH2209 No. 27 of wall A WA-27 CH2210 No. 28 of wall A WA-28 Unless othorwlso agreed In writing, this document Is n5uod by the Company subject to its General Conditions of Service pr. Mad overleaf. evadable on request or --lble at hltru irwww.}ge.comlenfTerma-end-Conditons Attention is drawn to the limitation of liability, Indemnification and JurlsdIctlon issues defined therein Any holds of thb document Is advised that Information contained hereon reflects the Company's rmdi at the time of 115 intervention only and within the limits of Client's matmetions, if any The Company's sob reapona Wily Is to Its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligatlona under ilia hansacton documenls. This document cannot be reproduced except In full. without prior written approval of the Company Any unauthorized alteration, !orgery or talslficatlon of the content or appearance of this document is unfawful and onenders may be pinsantad to the fullest extent of the law. Unless otherwise stated the results shown in this lest report refer only to the sample(s) tested and such Y-1 cr S7;,1 ien ai sample(s)arerelalned for 30 days only. A tunllon To checx l he authentic lty of testing n n s pecu on report A carlifluta, pi to se caria 0 s tel e is h on e. Ie6-755)Vol 144 i. or ommf. C11.09cchocMliess.cam IAlYhfbAlb]hM�4 tdr101rKDO9¢4dhf�� 1 & {d4�B 1 40M t (W23)88387M www.agsgroup.cdm.rn lia® iff�Sil�Ai�6 ♦iAS1c1 aM8$1=6F16i�1 1f�rltME(r l OW: 402280 t 0-231883PM age-dunaftstis om Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 22 of 40 CH2301 No. 29 of wall A WA-29 CH2302 No. 30 of wall A WA-30 CH2303 No. 31 of wall A WA-31 CH2304 No. 32 of wall A WA-32 CH2305 No. 33 of wall A WA-33 CH2306 No. 34 of wall A WA-34 CH2307 No. 35 of wall A WA-35 CH2401 No. 36 of wall A WA-36 CH2402 No. 37 of wall A WA-37 CH2403 No. 38 of wall A WA-38 CH2404 No. 39 of wall A WA-39 CH2405 No. 40 of wall A WA-40 CH2406 No. 41 of wall A WA-41 CH2407 No. 42 of wall A WA-42 CH2408 No. 43 of wall A WA-43 CH3004 Bottom surface of module 1 in unit A TA1 CH3005 Bottom surface of module 2 in unit A TA2 CH3006 Bottom surface of module 3 in unit A TA3 CH3007 Top surface of module 4 in unit A TA4 CH3008 Left surface of module 4 in unit A TA5 CH3009 Right surface of module 4 in unit A TA6 CH3101 Rear surface of module 4 in unit A TA7 CH3102 Bottom surface of module 4 in unit A TA8 CH3103 Top surface of module 5 in unit A TA9 CH3104 Top surface of module 6 in unit A TA10 CH3105 Top surface of module 7 in unit A TA11 CH3106 Top surface of module 8 in unit A TA12 CH3304 Rear surface of module 1 in unit B TB1 CH3206 Rear surface of module 2 in unit B TB2 CH3207 Rear surface of module 3 in unit B TB3 CH3208 Rear surface of module 4 in unit B TB4 CH3209 Rear surface of module 5 in unit B TB5 Unless otho�wise agreed in wnt:ng, this document Is Issued by the Company subject to Is General Conditions of Service printed overleaf. ,ram f available on request or accessible at htloaa/www.aas.cam/enRerms-erd-Conditions. Attention Is drawn to the limitation of liability, Indemnification and Jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reNects the Company's findings at the time of Ile intervention only and within the limits of Client's Instructions. if any. The Company's sob "•6' responslbIli is volts Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the bans soon documents, This document cannot be reproduced except In full. without prior written approval of" Company Any unauthorized alteration, forgery or falsification of Me content or appearance of this document is unlawful and offenders maybe prosecuted to the fullest ex1eM of the law. Unless otherwise staled the results shown In this test report refer only to the sample(s) tested and such esxxerS 70; vr, era •; fample(s) are retained for 30 days only. _ Attention To chats the authenticity of resting r nspecdon report A certificate, please contact us at tsleph one.104-755j 630'1443. _ or omall'. (, ►f,Qgi ChgCII�OIIe.Cgln J AlYhfb.4lb]hM�4 t�t011it01rrY14 l�t�' 1 ^& {d10�B' h 4= t www.apsgroup.twm.rn I p®i t3Sil�Aia6 Ask M6$ I =9F16i�tagR11� lliEr i JW: 40228t) t WO-n)SM67 001 age-dumalftsis coin Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 23 of 40 CH3210 Rear surface of module 6 in unit B TB6 CH3301 Rear surface of module 7 in unit B TB7 CH3302 Rear surface of module 8 in unit B T138 CH3107 Right surface of module 1 in unit C TC1 CH3108 Right surface of module 2 in unit C TC2 CH3109 Right surface of module 3 in unit C TC3 CH31 10 Right surface of module 4 in unit C TC4 CH3201 Right surface of module 5 in unit C TICS CH3202 Right surface of module 6 in unit C TC6 CH3203 Right surface of module 7 in unit C TC7 CH3204 Right surface of module 8 in unit C TC8 CH1-2-15 Ambient - Thermocouple information: Type K, 24AWG. . IV Unless otherwise agreed In writing, this document is Issued by the Company subject to As General Conditions of So"" purled overleaf. available on request or accessible at hltoa:llwwwsoa.com/enlTerms-and-Conditions. Attention is drawn to the limitation of liability, il• % xx Indemnlflcatlon and Jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reflects 0 Y` the Company's Gndlngis at the time of Ile Intervention only and within the limits of Clients InstruWons. iI any The Company's sob -� _ responslbiliry Is to Its Client and this document does not exonerate parties to a transaction from exerclOng all their rights and obligations under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsihoatbn of the oontent or appearance of this document is unlawful and offenders may be prosecuted I:;,.- to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such YMaI ITW4Sevices sample(S)areretsined lOY30 daysonly. Attenilon To chats the authenticity of testing r napection raport6certifiuta,pieaseconlact . !aiepnone.11ls-75+j 0?a'tddi. or afnall'. C►f.QocchochEa2ass.cgm J AlYhrb4lb]hM�4 tllrlOiYtt(�sY14 1�1� 1 & {dO�B�Ph 4D?Z60 r (8�23)88381A001 www.sMmp.oan.m �® f& �i1�Ait6�iAak M6# I t9F16i�t�gRta lliE� i 1a11: auazeo t Wa-M)MISMO nor F«n Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 24 of 40 WMA [Description of test results] Table 7: Overview of test timeline and key events Time Relative Time Photo (HH: MM: (HH: MM: SS) Event ID Event Description Reference SS 14:42:00 0:00:00 E1 Test Start -- Figure 12 Heater 1 and 14:42:30 0:00:30 E2 Heater 2 -- Energized Smoke release observed 15:28:26 0:46:26 E3 Release from initiating battery Figure 13 system enclosure. Smoke release observed 16:15:01 1:33:01 E4 Release from initiating battery Figure 14 system enclosure. 18:42:00 4:00:00 E5 Test Termination Chemical heat release rate versus time Description: No flaming extension observed outside the initiating unit. N/A Convective heat release rate (HRRc) versus time Description: N/A 1.4 1.2 1 Y 0 S 0. u r" o` 0:00:00 1:12:00 2:14:00 3:36:00 4:48:00 Relative, HH:MM:SS Figure 8. Convective heat release rate versus time Unless otherwise agreed in —I, ng, this document is Issued by the Company subject to As General Conditions of Service printed overlesf. available on request or accessible at haoa:Irwwwsaa.camlaMerma-arid-Conditions. Attention is drawn to the limitation of liability, ,I• - Indemniflcatlon and Jurtsdldion issues defined therein Any holder of this document la advised that Information contained hereon reflects the Company's findings at the time of Its b Intervention only and within the bmlls of Client's Instructions. if any. The Company's so responsibility is to Its Client and this document does rot exonerate pardes to a transaction from exorcising all their rights and otiNgatlons ` under the transaction documents This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawfld and oMenders may be prosemited r`• ''14J 1. ^axI:; ,.- to the fullest extent of the law. Unless otherwise staled the results shown in this test report refer only t .. r to the sample(s) tested and such fneet6altTetMtg Semen _; s Attention T retained for authenticity only. Attantlon TochecN the authenticity of testing inmpacdon nporta ortifluu, please contact us an telepn ona.le6-755j 03d'1443. or small'. C►f,Qocchoc Nliess.cgm _ l MYhfb.4lb]hM�4 tle�lOiYtt(�sY14 f�f�' it ^B. fdtO�B' h 4OZ260 t 86387W www.siMrotp.dan.m I�®•ftE��il�Ait6>yiAak�M6#It9F16i�t�gRtaT�lliErti loll: aoQzeo tfer:-nlee�a� �ha�F«h Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 25 of 40 Maximum incident heat flux on target units and .mall surfaces Result: Heat Flux Sensor ID Description of location CH1301 Surface of wall A, facing the center of front surface of module 4 in initiating unit CH1302 Surface of wall A, facing the center of front surface of module 5 in initiating unit CH1303 Surface of wall B, facing the center of right surface of module 4 in initiating unit CH1304 Surface of wall B, facing the center of right surface of module 5 in initiating unit CH1305 Center of rear surface of module 4 in target unit 1(Unit B) CH1306 Center of ringt surface of module 4 in target unit 2(Unit C) 14 12 tV 10 � Y 8 I f� � 6 � I c a� -0 4 1 AL i t 2 0 - - 0:00:00 0:28:48 0:57: 1:26:24 1:55:12 2:24:00 2:52:48 3:21:36 3:50:24 Relative Time, HH:MM:SS — CH1301 Surface of wall A, facing the center of Front surface of module 4 in initiating unit - CH1302 Surface of wall A, facing the center of Front surface of module 5 in initiating unit CH1303 Surface of wall B, facing the center of right surface of module 4 in initiating unit CH 1304 Surface of wall B, facing the center of right surface of module 5 in initiating unit — CH1305 Center of rear surface of module 4 in target unit 1(Unit B) — CH1306 Center of ringt surface of module 4 in target unit 2(Unit C) Figure 9. Incident heat flux on target wall surfaces and target BESS units. Unless otherwise agreed In writing, this document is issued by the Company subject to As General Conditions of So"" prided overleaf. available on request or accessible at httpaarwww.sus.com/antTe"s-and-Conditma, Attention is drawn to the limitation of liability, il• % xx Inderrmdlcallon and Jurisdiction issues defined therein Any holder of this document la advised that Information contained hmeom reflects 0 Y` the Company's Gndlngis at the time of Ile Intervention only and within the limits of Clients Instructions. it any The Company's sob - responalb liry Is to Its Client and this document does rot exonerate parties to a transaction from exerclOng all their rights and obligations under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or talsihoatbn of the oontent or appearance of this document is unlawful and offenders may be prosecuted I:;,.- to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such Yan6enlTtsMejSemtee'; sampla(s)areretainedlOY30daysonl Attention To chethe authenticity cs of testing r inspection reportacertificato.pteasecontact .= ralepnone.11ls-75+j 0?a'tddi. a small'. C►f.Qecchoclhf3ass.cgm A1Yh(b41b]hM�4 t�lOiYtt(�sY14 f�1� i ^B fdO�B h 4OZ260 t P-486381A00'I wtiviss grolp.can.m �® iff �ilgAit6�iAsk M6#It9F16i�t�gRtaTttlliE�i 1a11: 40225D tWa-n)66M67W 9PXNR8@SP— Member of the SOS Group (SGS SA) Project li COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 26 of 40 Peak smoke release rate and total smoke release Result: 1. Peak smoke release rate is 1.340 m2/s during test. 2. Total smoke release is 1181 m2 during test. 1.6 1.4 - I 1.2 — � 1 - N E 0.8 z z 0.6 0. 0.2 0 0:00:00 1:12:00 2:24:00 3:36:00 4:48:00 Relative Time, HH:MM:SS Figure 10. Smoke release rate versus time. 6M 1V Unless otherwise agreed In writing, this document Is Issued by the Company subject io Its General Conditions of So"" printed overlaef. available on request or accessible at hltoa:llwwwsoa.sons/enlTerms-ard-Cpndiborm Attenbon is drawn to the limitation of liability, w, il• % xx�� Indemnfflcatlon and Jurisdiction issues defined theroin Any holder of this document Is advised that Information contained hereon reflects •yam the Company's findings at the time of Ile Intervention only and within the limits of Clients InstruWons. II any The Company's sob r�_ responsiblliry Is to Its Client and this document does not exonerate parties to a transaction from axercieing all their rights and obligations ' under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders maybe prosecuted I:; r• to the fullsat extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such ynn6atlTtsMe)Semtee '; sampls(s) are retained for 30 days only Attenilon To chats the authenticitof testing r Inspection report A certificate. please contact s- !eleph on.-106-755)630'1443 a enroll. (,yf.QecchochlitsYa.cgm AlYhib4lb]hM�4 tllrlOiYtt(�sY14 1�1�» 1 ^& {dO�B�Ph 4D?Z60 t (8�23)88381A001 www-SIMMlq.twm.rn �® f& �i1�Ait6�iAak M6# I t9F16i�t�gRtaT lliE� i loll: 402260 t ler>-M)eeMaTIM 9PMAS& — Mwrkw of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 27 of 40 Flammable gas generation and composition Flammable gas generation: ❑ YES ❑ NO Flammable gas content ? 25% of LFL or not: N/A. Description : Total gas generation during test: 1769 L (25°C,101kPa) Recommend smallest room for installation: >_ 142 m3 2000 1800 1600 1400 Q a 1200 c v 0 1000 V Qt 800 _E 60D 400 200 0 0:00:00 1:12:00 2:24:00 3:36,00 4:48:00 6:00:00 Relative Time, HH:MM:SS -Wethdi C ide `.t"tane Ethy'ene d--Hydrtgenfluori:le —Nitrousoxide —Hydrogen Figure 11. Online flammable gas content measurements during test. (Remark: The content of other hydrocarbons is below the detection limit of the test equipment.) MW Unless ottlerwtse agreed In writing, this document is Issued by the Company subject to As General Conditions of So"" pnrded overleaf. available on request or accessible at bliss:llwwwsoa.aom/enlTerms-ard-Conditions. Attention is drawn to the limitation of liability, ��tt,,il• % xx�� Indemnlflcallon and Jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reflects 0 •yam the Company's findings at the time of Ile Intervention only and within the limits of Clients InstruWons. it any The Company's sob r�_ responsiWliry Is to Its Client and this document does not exonerate parties to a transaction from exerclOng all their rights and obligations ' under the transaction documents, TNs document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is urllawful and offenders maybe prosecuted I:; ,• to the fullsat extent of the law. Unless otherwise staled the results shown in this test report refer only to the sample(s) tested and such ynss6at1Tta5tgSemtee'; sampls(s)are retained for 30it" onl Attention To thethe authenticity ca of testing r inspection report A certificate. please cow-i .- !eleph on.-106-755)630'1443 a small'. C"'DocchochtlksYs.cgm _ 1 AIYh(b.41b]hM�4 t�1011itlUsY14 161�' D ^& {dIO�B' h 40Z260 t P")86387M www.sgagroup.com.cn �® 11& �i1�Ai16�iAak M6#I4a= t106-M)663676IN WNn — Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 28 of 40 Locations and visual estimations of flame extension and duration from the unit Flame extension : ❑ YES ❑ NO Description : No external flaming observed. N/A Table 9: Data during test OCV of Battery OCV of Battery Module ID Module Before Module After Test, (V Observation Results Test, (V dc) dc) Module 1 of 53.315 53.315 No gas venting observed. No external initiatig unit flaming observed. Module 2 of 53.315 53.315 No gas venting observed. No external initiatig unit flaming observed. Module 3 of 53.320 53.315 No gas venting observed. No external initiatig unit flaming observed. Module 4 of Gas and smoke venting observed. No 53.320 0 external flaming observed. No flying initiatig unit debris observed. No explosion observed. Module 5 of 53.320 53.315 No gas venting observed. No external initiatig unit flaming observed. Module 6 of 53.320 53.320 No gas venting observed. No external initiatig unit flaming observed. Module 7 of 53.320 53.320 No gas venting observed. No external initiatig unit flaming observed. Module 8 of 53.320 53.320 No gas venting observed. No external initiatig unit flaming observed. Measured Maximum Temperature Rise of Wall Surface Thermocouple ID CH2304 Measurements, (°C) 122.9 (temperature rise 94.3 °C) Location Surface of viall A Limits: LT <_ 97 °C Measured Maximum Surface Temperature of Modules within the Target BESS Units Thermocouple ID CH3208 Measurements. (" C) 158.1 Location Rear surface of module 4 in unit B Limits: Tmax. <_209.4 °C Cheesecloth indicator used or not ❑ Yes ❑ No Description of cheesecloth indicator after test: No flaming or carbonizing of the cheesecloth indicator. Supplementary information: N/A U niwa omorvlxe agreed In vml.ng, this document Is Issued by the Company subject to As General Conditions of Service P rhied ovorleaf. evadable on request or accessible at httosirwwwsas.wmlenRerms-and-CondiLona Attention is drawn to the limitation of liability, Indemnification and Jurisdiction issues defined therein Any hold of this comment Is advised that Information contained hereon reflects the Company's findings at the time of Its Intervention only and within the limits of Client's Instructions. if any. The Company's sole responslblllly Is to Its Client and this document does not exonerate ponies to a transaction from exercising all their fights and obNOatlone under the Irene ection documents. This document cannot be reproduced except In full. without prior written approval of the Company Any unauthorized alteration, forgery or falsification of the content or appearance of this document Is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise staled the results the" in this test report refer only to the sample(s) tested and such .ra;r S'�sl.rp i^.n ces -; sampia(S)areretained lor30 dayionly. _ Atteillon To theca the authenticity of testing r nspecdon reports certificate. please contact us at tslephone.I84-755j63071443. _ or omall'. C►f,Qocchockillsse.ebm _J MYhfb.4lb]hM�4 tlelrlOiYtt(�eY14 f�f�' it ^B. fdIO�B' h40?Z�0 t(8�23)88387A001 www.slMrolp.con.m �®•f&��iM�Aii6>yiABkl'1't$M6$ I t9F16i�t�lltt�!ltEr i 16M: aoQzeo t fart-nlee�a� �ha�F«n Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 29 of 40 WMA Figure 13. Photo 02 of initiating BESS unit and target BESS units during test- Unless otherwise agreed In wnf:ng, this document Is Issued by the Company subject to Its General Conditions of Service prinked overkef, avaibble on a"tiesl or accessible at htloa:llwww.aaa.cam/enlTerms-end-CandAwna. Attention is drawn to the limitation of liabllity, Indemn10callon end jurisdiction issues defined therein Any holds of Ihb 2c nl at b advised that Information contained hereon reflects the Company's findings at the time of its intervention only and whin the fill il is of Client's 1naWctions. if any The Company's sob responsibility Is to Its Client and this document does rot exonerate parties to a transaction from exercising all their rights and obfigation t under the transaction documents. This document cannot be reproduced excepl In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders maybe prosecuted to the fullest extent of the law. Unless otherwise staled the results shown In this test report refer only to the sample(s) tested and such csv2or S Trstny vrrcts '; sample(s) are retained for 30 days only. _ Attenllon To state the authenticity of testing t napecuon report A certificate, please contact us at tsiephone.IB4-755j 630'1443. _ or omall'. C►f,QpcchacllillOIIe.ngrn :l Mlelb6.lb]%�ullb4�t�l�ItIl�IrlOiYtt(�I►Y14�f�t�+�il�^B.�{dtO�B'�h 40?Z�0 t (8�23)88381A001 www.ti(pprolq.edm.rn �® f& �iM�Aii6yiAaicllz$Itlr> I t9F16ii�tggRta !ltE� i OM: 40225D t (air-n)SMISTIM 9PMha&P— Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 30 of 40 Figure 14. Photo 03 of initiating BESS unit and target BESS units during test. ON . IV Unless otherwise agreed In writing, this document is Issued by the Company subject to Its General Conditions of So"" printed overleaf. available on request or accessible at hltoa:llwwwsoa.Coco/enlTerma-erd-Can"ga. Attenoon is drawn to The limitation of liability, w, il• % xxIndemnfflcatlon and Jurisdiction issues defined theroin Any holds 9f thb d9cumant la advised that Information contained hereon reflects •yam Ins Company's findings at the time of Ile Intervention only and within the limits of Clients InstruWons. iI any The Company's sob responalb liry Is to Its Client and this document does not exonerate parties to a transaction from exerclOng all their rights and obligations ' under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders maybe prosecuted I:; ,• to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such ynn6g11TtsMa)Semtee'; sampla(s)are retained for 30it" onl Attenilon To chats The authenticity of testing onspection report A certificate. pie... conl-i - !eiephone-I8e-755ja30'1447. 9r small'. (, tf,Q99ChgCITi�0IIa.99m _J MYh(b.41b]hM�4 tIl�IrlOiYtt01ap14 1�1�' 1 ^& {�dtO�B' h 40?Z�0 t M")88381W www.sWratp.twm.rn �® f& �i1�Ait6�iAak M6# I t9F16i�t�gRtaT lliE� i OM: 40225D t(er:-n)eeMaTIM 9PMAS& — Mwrkw of the SGS Group (sae SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 31 of 40 WMA Figure 15, Photo 01 of initiating BESS unit and target BESS units after test. Figure 16. Photo 02 of initiating BESS unit and target BESS units after test. Unless otherwise agreed In writing, this document is Issued by the Company subject to Its General Conditions of Service printed overleaf. available on request or accessible at httw:llwww.aas.com/enRerms-end-CandHiana. Attention Is drawn to the limitation of liability, Indemnification and jurisdiction issues defined therein Any holder of this doaimenf is advised that Information contained hereon reflects the Company's findings at the time Of Its intervention only and within the Mmlla Of Client's InsuuWona, if any, The Company's sob responsibility Is to Its Client and this document does not exonerate parties to a transaction from eserdsMg all their rights and ohllgatlona under the transaction documents. This document cannot be reproduced except In full. without prior written approval of the Company Any unauthorized alteration, forgery or felsthcatbn of life content or appearance of this document is unlawful and offenders may be prosecuted r^.ry.•;tY,l!IJ l; (:. , to the fullest extent of the law. Unless otherwise staled the results shown In this test report refer only to the sample(s) tested and such YnesIentTtsligSemce _; samp(a(a)are retained for 30daysonl Attenllon To chats the authenticity of testing inspection report A certificate. piease conlad us i t ts(ephone.le6-7ss)s3o' 1443. or omall'. CH.DoccphockilkOIIsa..cydm wwilts gfoup.com.cri I p® i&7�11�Aii6YiA5�c9rt$M6 (f9F16i�t�gR1/ JIME�I 1611: 4(= t (ery-n)eIMISMI f %la-drilinaIROPMh Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF UL 9540A Unit V1.0 Page 32 of 40 WMA Figure 17. Photo 03 of initiating BESS unit and target BESS units after test. Figure 18. Photo 04 of initiating BESS unit and target BESS units after test. Unless otherwise agreed In wnt.ng. this document Is Issued by the Company sucfoct to IsGeneral Conditions of Service panted ovedeef. pt 7�D available on request or accessible al httoa:llwww.asa.cam/en/Terms-erd-Candibona.AWntion q drawn to the limitation of liability, Indemniflcallon end Jurlsdktlon issues defined therein Any holder of Ihla daament hi advised that Information contained hereon reflects Ia Company's findings al the time of its Intervention only and within the limits of Cbent's Instructions, if any. The Company's sobresponsibility Is to Its Client entl this document does rot exonerate parties to a transaction from exercising all their rights and obfigaflonsunder thetransaction documents. This document cannot be reproduced except In full. without prlor written approval of the Company Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful end offenders maybe prosecuted to the fullest extent of the law. Unless otherwise staled the results shown In this test report refer only to the samples) tested entl such sampisp)areretsinedta30deysont Attenllon To chats the authenticity of testing imspection report A certificate. piease contact us at telephone.tea-755)0?071447. or omall'. (, ►f,Q99Cph�g.,C ly1i�0IIsa,,.9y91n �,,r,, I N�Ib.B.(bif�la( 9y("�.T�pWow^ ftokiLLyt�aa/MftDoVkiWO*0 4� t ")863VW wwivu; gfoult.olown.Q1 Ili®i t�S11�Ai� allonts�5 all 16aa- {eari� Er) ": 4�280 l(8fr?3)88iB76001 agafina�BpaLatn Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 33 of 40 WMA Figure 19. Photo 01 of initiating BESS unit after test. Unless otherwise agreed In wnf•ng, this document is issued by the Company subject io Its General Conditions of So"" pruned overleaf. available on request or accessible at httpa.ttwww.sus.com/antTe"s-and-Gondit,ma, Attenbon is drawn to the imitation of liability, xx�� Indemnlflcatlon and Jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reflects •yam the Company's findings at the time of Ile Inlervenoon only and within the limits of Clients Instructions. IF any The Company's sob r�_ responsRNliry le to Its Client and this document does rot exonerate parties to a transaction from exercising all their rights and obhgationa under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or tatslhcatbn of the oontent or appearance of this document Is unlawful and offenders may be prosecuted I:;,.- to the fullest extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such ynn6g11TtsMe)Semtee'; sampla(s)areretainedlOY30daysonl Attention To checs the authenticity of testing l Inspection report A ceitificate•please comas ,=-Ie4ph-ii-184-755)03071443. or afnall'. (, ►f,Qgc ChgCltt�sIIa.ggm .'I a (b.�.(bif�lxpa(v�eey �Iy�y11(��I,� paQ�I� 14�M1e1e�1�L y.aalp IQ!„adyRa{�`fll�4 f/(a��✓ www.sMroull.00m.1T T®' t�r�TL+4�1 �111Yn1K51aaS( MGM- {es riftiS�l ": tt a--M) MM aP.dinafBga•Cpn Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 34 of 40 Figure 20. Photo 02 of initiating BESS unit after test. Ilk Unless otherwise agreed In wnl•ng, this document is issued by the Company subject io Its General Conditions of So"" pruned overleaf. available on request or accessible at httpa.ttwww.sus.com/antTe"s-and-Cgndit,ma, Attenbon is drawn to the imitation of liability, xx�� Indemnlflcatlon and Jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reflects •yam the Company's findings at the time of Ile Inlervendon only and within the limits of Clients Instructions. IF any The Company's sob r�_ ration sRNliry le to Its Client and this document does rot exonerate parties to a transaction from exercising all their rights and obhgationa under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or tatslhoatbn of the oontent or appearance of this document Is unlawful and offenders may be prosecuted I:;,.- to the fullest extent of the law. Unless otherwise staled the results shown in this test report refer only to the sample(s) tested and such wfn6at1Tta51gSemtee'; sampls(s)areretainedlOY30daysonl Attention To checs the authenticity of testing l Inspection report A certificate•please conies ,=-Ie4ph-ii-184-755)s3071443. or afnall'. Cyf,Qocchoclit (final ogm _'I N�I�..(bif�xfla(viea$y Iyy(.�.T pa(� I��M6ee�1�L y.aa/p lays I `f�Q 4 f /(a��✓ wwWgt!.aroup.olancri T®' t�r�TL+4�1 �111Yn1K51aaS ( MGM- {es riftiS� l ": t t116-M) MO a�'dana�Bga'Cpn Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 35 of 40 Figure 21a. Photo y test. module after Figure 21 c. Photo 02 of thermal runaway location. . IV 'Figure 21b. Photo 01 of thermal runaway location. is Figure 21d. Photo 03 of thermal runaway location. Unless otherwise agreed In writing, this document Is Issued by the Company subject to As General Conditions of So"" printed overleaf. available on request or accessible at hltoa:llwwwsoa.aom/enlTerms-ard-Conditions. Attention is drawn to the limitation of liability, xx�� Indemnlflcatlon and Jurisdiction issues defined theroin Any holder of this document Is advised that Information contained hansom reflects •yam the Company's Gndlngis at the time of Ile Intervention only and within the limits of Clients InstruWons. it any The Company's sob r�_ responsibIliry le to Its Client and this document does rot exonerate parties to a transaction from exerclOng all their fights and obligations ' under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders maybe prosecuted I:;,•i to the fullsat extent of the law. Unless otherwise slated the results shown in this test report refer only to the sample(s) tested and such ynn6atlTtsMejSemtee'; sampls(s)are retained for 30it" onl Attenilon To chats the authenticity of testing r Inspection report A certificate•please cont-i ,=- telephone. 104-755) 630' 1443 a amoll'. C►f,Docchoclickfulss..cgur :1I1MMfb.B.(bif�lxpa(bvbee..y�Yyy(�,.T pa(� I��M6ee�1�L y.aa/p IQla�y+`eWtlf�Q 4OZ260 t r(p")8638%M wwW.sMroull.00m./T 1 �®'� t�r�TL+4t1 �111Yn1K51aaS ( MGM- {ea riftiS� l ": 4� t t a--M) MM 416.dinfiftit Cpn Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 36 of 40 WMA 145.0 12S.0 1050 v n 85.0 E a GS 0 45.0 250 0:00-00 0:29:48 O:S7:36 126:24 1:SS:12 2:24 00 2:52.48 3:21:96 Relative Time, HHMN11S —CHODOI WA-1 —CH00D2 WA-2—CH0003 WA-3 CH0004 WA-4 —CHOOOS WAS—CH0006 WA-6 —CH0007 WA-7 —CH00D9 WA-8—CHOOIO WA-9 —CH0101 WA-IO—CH0103 WA-11—CH0104 WA-12 —CNO105 WA-13 CH0306 WA-14 CH0107 WA -IS CHOIOB WA 16 -- CH01M WA17 CH011D WA-18 —CHOW1 WA-19 —CH02D2 WA 20—CH0703 WAQI—CH0204 WA 22 —Cli WA-23—CH2206 WA-24 —CH2207 WA-25 CH2209 WA-26 CH2209 WA-27 CH2210 WA-28 CH2301 WA-29 - - CH2302 WA-30 —CH2303 WA-31—CH23D4 WA-32—CH2305 WA•33—CH2306 WA-34 — CH2307 WA-35 — CH2309 WA-36 .CH2310 WA-37 CH2401 WA-38 C1112402 WA-39—CH2403 WA-40 CH2404 WA41—CH2405 WA-42 —CH2406 WA-43 —CH2407 WA-44 —CH24M WA45 Figure 22. Temperature fsurement results on wall A. 125.0 115.0 105.0 95.0 U d 85.0 f A 75.0 f E 65.0 -- I SSA 7y I 1 0 - _ _ - - Dd]O:OD 0:57:36 1- 155:12 2:24:00 2 WAS 3 21:36 350:24 Relative Time, HH:MM:SS 1 WB-I —CH2O02 WB-2 2003 WB-3 CHZDD4 W04 —CH2005 W8-5—CH2OD6 W" H20D7 WS-7 —CH2008WB-8—CH2009 WB-9 —CH2O10 WB-1O—CH2101 WB Il—CH2102 WB-12 CH21D3 WB-13 CH2104 WB-14 CH2105 WO-15 CH21D6 WB-16 -- CH2107 WB17 — CH2108 WB-18 CH2109 WO-18—CH2110 WO-20—CH2201 WB-21—CH2202 WB-22—CH2203 WB-23—CH2204 WB-24 DOI WO-25 CH1002 WO-26 CH2003 WO-27 CH1004 WB-28 CH1005 WB-29 -- CH1006 WB-30 WS-3I —CHI008 WO-32—CH10D9 WB-33 —011020 WB-34 —CH1101 W B-35—CH1102 W B-36 03 WB37 CH1104 WO38 CH1105 W1339 CH1106 WB-40 CH1107 WB41—CH1108 W642 —CH1201 WB-43—CH1202 W844—CH1203 WB-45—CH1204 WB46—CH1205 WB47—CH1206 WB48 CH1207 WB-49 CHI 208 W8-50 CH1209 WO-Sl CH1210 WB-52 CHI 301 WB-53 CH1302 WB-54 Figure 23. Temperature measurement results on wall B. �` l A 4:19:12 _ Unless oMerwiae agreed In writing, this document is Issued by the Company subpct to its General Conditions of Service printed overleaf, r avellabie on requsa or .-..,Ibis al httoaaflot scam/enfTerms-end-Conditions. Attention Is drawn to the limitation of liability, �- Intlemn10cellon end Jurisdiction issues defined therein Any holder of this document b advised that Information contained hereon reflects the Company's f I r?s al the time of Its inlerveMlon only and within the limits of Client's instructions. any. The Company's sob responsibility Is to Its Client end this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document Is unlateral and offenders may be prosecuted is:,.i to the fullest extent of the law. Unless otherwise staled the results shown in this test report refer only to the sample(s) tested and such InfNl6enlTalYg Saacn _; sample(s) are retained for 30 days only. Attention To check the authenticity of testing r Inspection report acertificate. please contact ..at telephone-144-755)03071443. or ontall'. CH.Qocchochilli4IIs.gem :1 AIYhIbQIb2FIpnRaE,9rld13114t.dljt0it114 4 flit l fi��B' 40M f (88-23)8638'1W waw.epagrolp.ptan.m I�®'i&t�S1f��Ai1i6�11on a•5 ,() 16am-{esri��MEr� �11: 4M= f(8fr23�883B76001 aBadana�e9e �ln Mentor of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF UL 9540A Unit V1.0 Page 37 of 40 WMA 40D.0 350.0 30D.0 alJ 250.0 to �9 200.0 C a E F 150.0 10D.0 50.0 0.0 0:00:00 0:28:48 0:57:36 1:26:24 1:55:12 2:24M 2:52:48 3:21:36 Relative Time, HH:MM:55 —013004 Bottom surface of module i in unit A—C111MM Bottom surface of module 2 in unit A 4 —CH3006 Bottom surface of module 3 in unit A—CH3007 Top surface of module 4 in unit A —CH3008 Left surface of module 4 in unit A—CH3008 Right surface of module 4 in unit A —CH3010 Rear surface of module 4 in unit A—CH3101 Bottom surface of module 4 in unit A —CH3102 Top surface of module 5 in unit A—CH3103 Top surface of module 6 in unit A —CH3105 Top surface of module 7 in unit A—CH3106 Top surface of module 8 in unit A Figure 24. Temperature measurement results on the initiating unit (unit A). 3:50:?4 — CH3207 Rear surface of module 3 in unit B CH3208 Rear surface of module 4 in unit B —CH3209 Rear surface of module 5 in unit B — — CH3210 Rear surface of rnudule 6 in unit B —CH3401 Rt,.ir am I'm of unriulo 7 in unit R — CH330? Rear t(a fac v of module R in a lit R Figure 25. Temperature measurement results on target units (Unit B) Unless otherwise agreed In wnl.ng, thla documant is Issued by the Company sub)oct w Its General Conditions of Service printed ovetrleef, available on request or accessible at hmosdtwww.sas.camlan/Terms-Grid-Condmana. Attention is drawn to the limitation of liability, Indemnificallon and jurisdiction Issues defined therein Any holder of this document Is advised that Information contained hereon reflects the Company's finding at the time of Its Intervention only and within the Simits of Client's Instructions. if any, The Company's sob responalWllly is to Its Client and this document does not exonerate parties to a transaction from afferdeing all their rights and obligations under the transaction documents. This document cannot be reproduced except In full. without prior written approval of lie Company Any uneutnorized alteration, forgery or falsMOation of the content or appearance Of this document Is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise staled the results shown in this test report refer only to the sample(s) tested and such samplap) are retained for 30 days only Attention To checs the authenticitof testing inspection report A cartifiute, please contact usat telephone.ISO-755)03071443. a omall'. Gtf.Q99Chga Ml�0IIa.99m MYh1b41b]FfM�4 tJYriOiYtt0ttY14 f�fLt i ^B tdO�B h 40M t WM)f1f{38r' W www.sMhlup.cw.m �® ll& �iM�Aii6itiAskflt$M6 I t916ii�t'agR1a»!ltEr i 11W 411M I lea-M)883676001 Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 38 of 40 85.0 75.0 65.0 U o� 55.0 m a E 45.0 35.0 25.0 0:0 WMA —CH3107 Right surface of module 1 in unit C — CH3308 Right surface of module 2 in unit C —CH3109 Right surface of module 3 in unit C CH3110 Right surface of module 4 in unit C —CH3201 Right surface of module 5 in unit C—CH3202 Right surface of module 6 in unit C —CH3203 Right surface of module 7 in unit C—CH9204 Right surface of module 8 in unit C Figure 26. Temperature measurement results on target units (Unit C) 11111111 CH 1S01 Side surface A of Cell 1 — CH2502 Side surface A of Cell 2 CH250-1 Side surface A of Cell 3 — CH2s04 side surface A of Cell o —CH2.505 We surface B of Cell 5 — CH25M Sido surface B of Col 6 —CH2507 *face B of Cell 7—CH2508 Side surface B cf Cell 9 —CH25*-brge surface of cell 3, between cell surface and Heater 2 — C1-13001 Button surface of cell 2 —CH3002 Bottorn surface of cell 3—cH3003 Bullom scr'ace of cell 4 Figure 27. Temperature measurement results on the initiating module. Unless otherwise agreed In wnl.ng. this document Is Issued by the Company sucfoct co Is General Conditions of Service panted overleaf. available on request m accessible at httoaarwww.sas.camien(Terms-aid-Conddims. Attention Is drawn to the limitation of liability, 11• - Indemniflcsimn and JurlvdIctlm issues defined therein Any holder of this document is advised that Information contalned hereon reflects ¢, the Company's Gn,117s at the time of Its Inlmvenden only and within the pmlts of Client's Instructions. if any, The Company's sob R r�_ responaib lIty le to its, and this document does rot exonerate parties to a transaction from exercising all Malr rights and obligations under the transaction documents. This document cannot be reproduced except In full. without prior written approval of the Company Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted r�^.ry.•;tY,l!IJ i; I:;,.- to the fullest extent of the law. Unless otherwise staled the results shown in this test report refer only to the sample(s) tested and such nts�eltTta5lgSemte _; sampfa(A)are retained for 30days onl AtNntlon To Chats the authenticity of testing imapection sport A Cartifiute.please contact us at telepn one-146-755j 0?0'tddi. or small'. Cff.Q99ChgC11f0IIe.99m llfefb4lb]%qulb4 tJYrtOiYtt(hrY14a++f�tt+t i�f^B tdo�Bmapth 4o?ZBo t (8�23)88381A001 www.egagrolP-cw.cn �® f& �i1�Ait6iliAak M6#It9F16i�t�gRt lliE�i ": 4a= tWa-n)SMSMO %litUfthaftle— Member of the SOS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 39 of 40 NOTES TO THIS TEST REPORT Copyright Cc) 2021 SGS-CEC New Energy Technology (Chongqing) Co., Ltd. All rights reserved. This publication may be produced in whole or in part for non-commercial purposes as long as SGS- CEC is acknowledged as copyright owner and source of the material. SGS-CEC takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and content. 2. According to the standard, instruction sheets and other texts required by the standard should be written in the official language(s) of the country in which the product is to be sold. The applicant should ensure that the product in future production fulfils the receptive standard requirements. 3. The components performed satisfactorily during testing and are considered to be suitable for use in the sample tested. - - - End of Report - - - . IV Unless ottnenatse agreed In writing, this document is Issued by the Company subject to As General Conditions of So"" printed overleaf. available on request or accessible at hltoa:llwwwsoa.com/enlTerms-and-Conditions. Attention is drawn to the limitation of liability, xx�� Indemnlflcatlon and Jurisdiction issues defined therein Any holder of this document Is advised that Information contained hereon reflects •yam the Company's Gndlngis at the time of Ile Intervention only and within the limits of Clients InstruWons. iI any The Company's sob r�_ responsiblliry le to Its Client and this document does not exonerate parties to a transaction from axerclOng all their fights and obligations ' under the transaction documents, This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders maybe prosecuted I:; ,• to the fullsat extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such Wfn6atlTtsfYgSemcee'; sampls(s)are retained for 30it" onl Attetilon To chats the authenticity of testing r Inspection report A certificate. iiesse cont-i ,=- telephone. 104-755) 630' 1443 or omall'. Cyf.DocchockiliksIIs.cgm WINKSMIDO-conl.cft I h®i t3Silf�Ai�6i 11on �5M66� I S9F16a s- {ea rid lllEr l ": 4a= t Wa-M)SMISMO %Nft a@ega— Member of the SGS Group (SGS SA) Project No.: COES2208000153BA TRF_UL 9540A Unit_V1.0 Page 40 of 40