The URL can be used to link to this page

Home My WebLink AboutAPPROVED ELECTRICAL PLANS - 22-00502 - Mountain West Rental and SalesAuthor Name Author Email Author Phone No.: Alex Owens Alex.Owens@rexburg.org 208-372-2330 Todd Smith Todd.Smith@rexburg.org 208-372-2181 Description : Mountain West Rental and Sales Address : Record Type : New Commercial Building Document Filename : 22-07-26_Mountain West Equip Rexburg_Electrical_REV#1.pdf Comment Author Contact Information: Corrections in the following table need to be applied before a permit can be issued Review Report Approved # 22-00502 Page Reference Annotation Type Author : Department Status Page Review Comments Applicant Response Comments E0.0 Stamp Alex Owens : Electrical Open 1 Approved - Electrical Inspector E1.0 Stamp Alex Owens : Electrical Open 2 Approved - Electrical Inspector E2.0 Stamp Alex Owens : Electrical Open 3 Approved - Electrical Inspector E3.0 Stamp Alex Owens : Electrical Open 4 Approved - Electrical Inspector New Commercial Building As per Resolution 2022-07, adopted April 6, 2022, new development is required to follow standards for the installation of fiber conduit and distribution boxes. Location of conduit and distribution boxes need to be identified and shown on plans. Approval of plans does not constitute approval of variance from code Powered by TCPDF (www.tcpdf.org) ELECTRICAL SPECIFICATIONS 1. INTENT: Provide and install complete and operable electrical systems including but not not limited to; lighting, power, receptacles, data, fire alarm ande etc. Provide all required connections to all Mechanical and Plumbing equipment, as indicated and required, including all conduits, wiring and controls. Coordinate with mechanical contractor and drawings. 2. COMPLIANCE WITH CODES: All work and material shall comply with all applicable codes, safety orders, laws, ordinances and regulations of governing authorities and other agencies having jurisdiction including regulations of the State and Local Fire Marshall, unless detailed as specified to a more restrictive standard or higher requirement. 3. INTERPRETATION OF DRAWINGS: The electrical drawings are essentially diagrammatic in that all provisions necessary to conform to structural, architectural, mechanical and plumbing systems can not be shown. All installations shall be adjusted as necessary to conform and to avoid obstructions, without additional cost to the owner. All work, material and equipment called for by notes, schedules or otherwise indicated on the drawings shall be furnished and isntalled as though fully set forth in these specifications. 4. VISITING THE SITE: Contractor shall visit the site and become acquainted with conditions to be encounterd. Extra funds will not be allowed due to failuer to examine the site and to included existing conditions in bid price. 5. COORDINATION WITH UTILITIES: These plans have been prepared without utility company comments. The contractor shall verify exact requirements for the electrical, telephone and communication services with the utility company representatives and provide all work and pay all costs for a complete and operating systems, as directed by the governing utilities. 6. MATERIALS AND WORKMANSHIP: All workmanship shall be performed by skilled electricians using the best standard practives of the trade. All materials shall, unless otherwise noted, be new and in perfect condition and working order. All material for similar uses shall be of the same type, material and manufacturer for ease of future maintaenance. All equipment shall be readily accessible for maintenance and repairs. All materials, fixtures and equipment shall be covered or sealed upon installation so as to provide for safety and to insure that operation and appearance will be maintained after subsequent construction operations. 7. EXECUTION: Raceway installation: Seperate underground conduits in a common trench 4" minimum horizontally, 12" minimum from other utility lines. Minimum conduit depth shall be 18". Coordinate conduit installation with pipes, steel, footings and ducts installed by other trades. Install conduit runs exposed to view parallel or at right angles to structural members, walls or building lines. Support conduit with one-hole malleable factory made pipe straps, fastended with screws. 8. OPERATING AND ADJUSTING: The owner reserves the right to operate any systems of equipment prior to final comletion and acceptance of the work. Such perliminary operation shall not be construed as an acceptance of any work. Each piece of equipment and all of the systems shall be adjusted to insure proper functioning and shall be left in first class operating condition. 9. CUTTING AND PATCHING: Do all drilling and cutting as necessary for installation of equipment or conduit. Cutting or drilling of structure is only permitted with prior approval of the owner and structural engineer. Where cutting and patching of work is necessary, use the same materials, workmanship and finish to neatly match all surrounding work. 10. CONDUIT: All conduit material and installation methods shall be as allowed by the NEC, local AHJ and as directed by the owner. 11. CONDUCTORS: Type THWN or THHN copper wire insulated for 600V. Smallest wire shall be #14 AWG unless noted otherwise. All wiring shall be Copper unless indicated otherwise. Type MC cable shall be permitted provided it is installed in concealed spaces and installation complies with the Local AHJ and NEC requirements. Use "Ideal Yellow" pulling compound for all wire pulls. Use Scotchlock connectors for all splices in #12 wire and tape bolted pressure connectors for larger wire. 12. GROUNDING: All conduit, branch circuits, feeders and etc. shall be provided with a grounding conductor. All grounding conductors shall be insulated and green in color, size as shown. 13. WIRING DEVICES: Devices shall be Standard type, Specification grade, color as selected by owner. Decora style devices are prohibited. Utilize GFCI and Tamper-proof devices in all locations as defined by the NEC. Wiring devices shall be as installed as allowed by the NEC, local AHJ. 14. DEVICE PLATES: Devices plate type and color shall be as directed by owner and as required by the NEC. 15. LIGHTING FIXTURES: As selected by owner and/or indicated in schedules. All light fixtures shall be installed and connected by the Electrical Contractor. 16. SERVICE EQUIPMENT & PANELBOARDS: Service Equipment: Shall be rated as such and shall comply with local utility co. requirments. . Panelbards: Shall be provided with typed writtend directories indicating loads being served. Maintain all required clearances around equipment as required by the NEC. All equpment dimensions to be field verified. 17. CLEAN-UP: Upon completion of the work, prior to final inspection, thoroughly clean all exposed fixtures, trim and equipment and leave the entire installation in a neat, clean and usable condition. Remove all cement, paint, grease, oil and other foreign substances. 18. TEST: Test all conductors for shorts, opens, grounds or other defects. Correct any defective work and re-test. Demonstrate continuous satisfactory operation of all electrical systems and equipment. Provide training to the owner on electrical systems as needed for owner operation and maintenance of building. 19. GUARANTEE: Prior to final acceptacne of the project, deliver to the owner a written one year guarantee on all workmanship, materials and equipment and agree to repair or replace all such defective items promptly that may occure during the warranty period; including repair or replacement of the premises that may be damaged due to faulty work and materials furnished under contract. ENTRANCE CONDUIT(S) 4" SQUARE BOX RAISED RING TO SUIT WALL RECEPTACLE - 20AMP RATED - SEE SPECIFICATIONS. NORMAL POWER COLOR - (SEE SPEC'S) COVER PLATE - STYLE & COLOR TO BE AS PER SPECIFICATIONS. CIRCUIT NUMBER TO BE WRITTEN ON BACK OF COVER W/FELT-TIP MARKER GREEN INSULATED GROUND CONDUCTOR TEE BAR GRID POWER SUPPLY CONDUIT FOR CEILING OR WALL "J" BOX. SUPPORT WIRE BY ELECTRICAL CONTRACTOR INDEPENDENT OF CEILING SYSTEM. (TYPICAL) ACOUSTIC CEILING TILE SUPPORT CLIPS ALL SIDES CIRCUITING & GENERAL SYMBOL SCHEDULE NOTE: ALL SYMBOLS MAY NOT BE USED SYMBOL DESCRIPTION KEYED NOTE REFERENCE1 BRANCH CIRCUIT HOME-RUN TO PANEL INDICATED A-1,3,5 3/4"C.-6#12,1#12G QTY & SIZE OF EQUIPMENT GROUND CONDUCTOR QTY & SIZE OF NEUTRAL AND PHASE CONDUCTOR(S) SIZE OF CONDUIT A-1,3,5 3/4"C.-6#12,1#12G PANEL AND CIRCUIT DESIGNATIONS EQUIPMENT GROUNDING CONDUCTOR TICK MARKS NEUTRAL CONDUCTOR(S) PHASE AND/OR SWITCH-LEG CONDUCTOR(S) BRANCH CIRCUIT/FEEDER CONCEALED IN CEILING OR WALL BRANCH CIRCUIT/FEEDER CONCEALED UNDERGROUND OR FLOOR NEW EQUIPMENT, DEVICES, ETC. EXISTING EQUIPMENT, DEVICES, ETC. DEMOLITION EQUIPMENT, DEVICES, ETC. DETAIL # / SHEET REFERENCE1 / ES101 *25,000A CALCULATED AVAILABLE FAULT CURRENT AT EQUIPMENT(SEE POWER RISER) LIGHTING SYMBOL SCHEDULE NOTE: ALL SYMBOLS MAY NOT BE USED SYMBOL DESCRIPTION PARKING AREA POLE LIGHT, SINGLE OR DOUBLE HEAD AS INDICATED ON DRAWINGS. REFER TO LIGHT POLE DETAIL FOR POLE INFORMATION. 2X4 FLUORESCENT OR LED FIXTURE 2X2 FLUORESCENT OR LED FIXTURE SURFACE MOUNTED FLUORESCENT OR LED FIXTURE STRIP FLUORESCENT OR LED FIXTURE WALL MOUNTED FLUORESCENT OR LED FIXTURE EXTERIOR WALL MOUNTED FIXTURE ROUND RECESSED FIXTURE SURFACE OR PENDANT FIXTURE LIGHT FIXTURE SUBSCRIPTS NL NIGHT-LIGHT(CONNECT TO UNSWITCHED LEG OF CIRCUIT) EXIT SIGN, WALL OR CEILING MOUNTING AS REQUIRED (SINGLE OR DOUBLE FACE) DIRECTIONAL CHEVRONS AS INDICATED; CONNECT TO UNSWITCHED LEG OF LIGHTING CIRCUIT THAT IS IN THE SAME AREA AS THE EXIT SIGNS. SHADED FIXTURE INDICATES AN EMERGENCY FIXTURE. PROVIDE WITH EMERG. BATTERY PACK OR CONNECT TO EMERGENCY POWER SYSTEM (WHERE APPLICABLE). CONNECT BATTERY PACK TO UNSWITCHED LEG OF LIGHTING CIRCUIT THAT SERVES THE SAME AREA AS THE EMERGENCY FIXTURE. PROVIDE WITH TEST LIGHT AND SWITCH. CEILING MOUNTED OCCUPANCY SENSOR, REFER TO OCCUPANCY SENSOR/SWITCH SCHEDULE FOR SENSOR TYPE AND ADDITIONAL INFORMATION. SWITCH MOUNTED OCCUPANCY SENSOR, LOW VOLTAGE SWITCHPOD OR DIMMER SWITCH, REFER TO OCCUPANCY SENSOR/SWITCH SCHEDULE FOR TYPE AND ADDITIONAL INFORMATION. SINGLE-POLE SWITCH (SEE SUB-SCRIPTS BELOW FOR ADDITIONAL INFORMATION) SWITCH SUBSCRIPTS 3 3-WAY SWITCH 4 4-WAY SWITCH D DIMMER SWITCH (COMPATIBLE W/ LOAD & LTG TYPES) F 7-DAY PROGRAMMABLE TIMER SWITCH (INTERMATIC MODEL EI500WC SERIES) P PILOT LIGHTED SWITCH F1 LIGHT FIXTURE TYPE DESIGNATION S ### WALL OR CEILING MOUNTED EMERGENCY LIGHTING UNIT W/BATTERY PACK CONNECT TO UNSWITCHED LEG OF LIGHTING CIRCUIT THAT IS IN THE SAME AREA AS THE EMERGENCY LIGHT. LV LOW-VOLTAGE SWITCH (PER DWG'S) T THERMAL-OVERLOAD SWITCH M SWITCH SUPPLIED WITH EQUIPMENT, INSTALLED BY E.C. WP WEATHERPROOF 2P DOUBLE POLE, SINGLE THROW SWITCH GENERAL LIGHTING NOTES: A. SYMBOLS SHOWN ABOVE MAY NOT REPRESENT ALL LIGHT FIXTURES USED ON PROJECT, REFER TO LIGHT FIXTURE SCHEDULE FOR ACTUAL FIXTURE INFORMATION INCLUDING FIXTURE TYPE, LAMPING, MOUNTING AND ETC. B. JUNCTION BOXES FOR LIGHTING CIRCUITING ARE NOT SHOWN FOR CLARITY. THE E.C. IS RESPONSIBLE FOR PROVIDING AND INSTALLING ALL JUNCTION BOXES REQUIRED FOR CIRCUITING OF ALL LIGHT FIXTURES THAT ARE NOT LISTED FOR "THROUGH-BRANCH CIRCUIT WIRING". C. IN GENERAL ALL SWITCH-LEG CONDUCTORS MAY NOT BE SHOWN ON DRAWINGS; E.C. SHALL PROVIDE AND INSTALL CONDUCTORS AS REQUIRED TO ACHIEVE CONTROL SCHEMES INDICATED AND DESCRIBED ON DRAWINGS. INCLUDING ALL 0 - 10V DIMMING CONTROLS BETWEEN SWITCH AND FIXTURES. D. ALL BATTERY EXIT SIGNS AND EMERGENCY LIGHTING TO BE CONNECTED TO THE UNSWITCHED LEG OF THE LIGHTING CIRCUIT IN THE AREA. ### F M POWER SYMBOL SCHEDULE NOTE: ALL SYMBOLS MAY NOT BE USED SYMBOL DESCRIPTION ELECTRICAL SWITCHBOARD EQUIPMENT, (SEE POWER RISER AND PANEL SCHEDULES FOR ADDITIONAL INFORMATION) 'MSB' 'T##'DRY-TYPE TRANSFORMER, (SEE POWER RISER FOR ADDITIONAL INFORMATION) 'LA' ELECTRICAL PANELBOARD, (SEE POWER RISER AND PANEL SCHEDULES FOR ADDITIONAL INFORMATION) DISCONNECT SWITCH, SIZE/POLES/TYPE AS INDICATED TYPES: 1=NEMA 1, 3R=NEMA 3R, 4X=NEMA 4X30A/3P/3R FUSED DISCONNECT SWITCH, SIZE/POLES/TYPE AS INDICATED TYPES: 1=NEMA 1, 3R=NEMA 3R, 4X=NEMA 4X30A/3P/3R (30A FUSES) COMBINATION STARTER & FUSED DISCONNECT SWITCH, SIZE/POLES/TYPE AS INDICATED. TYPES: 1=NEMA 1, 3R=NEMA 3R, 4X=NEMA 4X J JUNCTION BOX CR = CORD REEL; SEE DRAWINGS FOR INFORMATION CD = CORD DROP; SEE DRAWINGS FOR INFORMATION EQUIPMENT CONNECTION; COORDINATE CONNECTION WITH EQUIPMENT PRIOR TO ROUGH-IN MOTOR CONNECTION POWER AND/OR DATA SERVICE POLE FLOORBOX (SEE FLOORBOX SCHEDULE FOR ADDITIONAL INFORMATION) PUSHBUTTON STATION FB# SPECIAL RECEPTACLE (COORDINATE NEMA TYPE WITH EQUIP.) (REFER TO PANEL SCHEDULES FOR AMPS) CEILING MOUNTED DUPLEX RECEPTACLE (COORDINATE PLACEMENT WITH CEILING EQUIPMENT PRIOR TO ROUGH-IN) DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED BELOW 5FT GFCI-TYPE DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED BELOW 5FT DOUBLE-DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED BELOW 5FT GFCI-TYPE DOUBLE-DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED BELOW 5FT. RECEPTACLE AND EQUIPMENT SUBSCRIPTS AC ABOVE COUNTER WP WEATHERPROOF (UL LISTED WEATHER-RESISTANT) 42"MOUNTING HEIGHT AFF OR AFG IG ISOLATED GROUND S SURGE-PROTECTION TYPE REF REFRIGERATOR W WASHING MACHINE D DRYER (30A-240V RATED RECPT.) M MICROWAVE HVAC THERMOSTAT OR SENSOR; PROVIDE & INSTALL BACKBOX,3/4" CONDUIT AND CONDUCTORS TO ASSOCIATED HVAC UNIT. COORDINATE EXACT LOCATION & SIZE AND NUMBER OF CONDUCTORS WITH M.C. T SOR 30A/3P/3R SIZE 1 (30A FUSES) SMALL EXHAUST FAN CONNECTION TV 120V RECEPT. FOR TV; VERIFY HEIGHT WITH ARCH. DRAWINGS & ELEVATIONS USB 120V RECPT. WITH USB CHARGING PORTS EWC ELECTRIC WATER COOLER; (SEE DETAIL. RECPT. SHALL BE ACCESSIBLE, DO NOT MOUNT BEHIND HOUSING.) DISP GARBAGE DISP. (UNDER SINK) DW DISHWASHER (COORDINATE W/ MILLWORK, INSTALL PER NEC 422.16(B)(2)). M/R MICROWAVE/RANGE HOOD (COORDINATE W/ MILLWORK) R ELECTRIC RANGE (50A-240V RATED RECPT.) GENERAL SPECIAL SYSTEM NOTES: A. ALL DEVICES SHOWN AT OR NEAR MILLWORK/CASEWORK SHALL BE COORDINATED WITH THE ARCHITECTURAL ELEVATION DRAWINGS AND MILLWORK INSTALLER TO INSURE PROPER MOUNTING HEIGHTS. CONTRACTOR SHALL ADJUST DEVICES AS NECESSARY IN ORDER TO POSITION DEVICES SUCH THAT THEY WILL NOT FALL BEHIND MILLWORK, CABINETS OR BE DIRECTLY ABOVE SINKS OR MIDWAY BETWEEN TILEWORK/WALL OR WAINSCOATING, ETC. B. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO INSTALL A GFCI TYPE RECEPTACLE FOR ALL RECPTACLES SHOWN IN TOILET RMS, BATHROOMS, KITCHENS/SERVING AREAS, ROOFTOP, OUTDOORS OR WITHIN 6FT OF ANY SINK, BASIN, TUB OR FLOOR SINK AND ALL OTHER AREAS DEFINED BY THE NEC. SPECIAL SYSTEMS SYMBOL SCHEDULE NOTE: ALL SYMBOLS MAY NOT BE USED SYMBOL DESCRIPTION DATA OUTLET; _= # OF DATA CABLES, X=CONDUIT SIZE (SEE NOTES 1,2,3 BELOW)_D-X TELEPHONE OUTLET; _= # OF TELEPHONE CABLES, X=CONDUIT SIZE (SEE NOTES 1,2,3 BELOW) _T-X TELEPHONE/DATA OUTLET; _= # OF TELEPHONE/DATA CABLES, X=CONDUIT SIZE (SEE NOTES 1,2,3 BELOW) _T/_D-X CEILING MOUNTED DATA OUTLET; _= # OF DATA CABLES, X=CONDUIT SIZE (SEE NOTES 1,2,3 BELOW) _D-X A. COMMUNICATIONS CABLES SHALL HAVE BENDS NO GREATER THAN 90 DEG. B. CONDUITS FOR COMMUNICATIONS CABLING SHALL HAVE A MAXIMUM BEND RADIUS NOT MORE THAN 10X THE DIAMETER OF THE CONDUIT. C. ALL COMMUNICATIONS CONDUITS SHALL BE TERMINATED WITH AN INSULATED NON-METALLIC BUSHING AT BOTH ENDS. D. COMMUNICATIONS CONDUITS SHALL HAVE NO MORE THAN (2) 90'S WITHOUT A PULLBOX. PULL BOXES SHALL BE LOCATED IN ACCESSIBLE LOCATIONS AND SHALL BE SIZED AT LEASED 12X THE LARGEST CONDUIT DIAMETER IN LENGTH AND MIN, 4" DEEP AND 8" WIDE. E. IT SHALL BE THE RESPONSIBILITY OF THE E.C. TO INSURE THAT THE PATHWAY FOR THE DATA CABLING DOES NOT CREATE CABLE LENGTHS TO EXCEEDS THE LENGTH OF 295FT FROM OUTLET TO PATCH PANEL, THIS INCLUDES SERVICE LOOPS AND PATCH CORDS. F. WHERE CABLE TRAY IS UTILIZED IN THE PROJECT. COMMUNICATION CONDUITS ENDING AT THE CABLE TRAY SHALL EXTEND 1" OVER THE SIDE INTO THE TRAY. GENERAL SPECIAL SYSTEM NOTES: ###_D-X SPECIAL SYSTEMS NOTES: 1. UTILIZE 4 11/16" DEEP BOX WITH REQUIRED MUDRING AND CONDUIT TO ABOVE NEAREST ACCESSIBLE CEILING OR DATA RACK, TERMINATE WITH INSULATED THROAT BUSHING. PROVIDE QTY OF CABLES INDICATED FROM OUTLET TO NEAREST TELE/DATA ROOM. SEE DWGS FOR ADDITIONAL INFORMATION. UTILIZE J-HOOKS 3FT ON CENTER FOR SUPPORT OF CABLING WHERE CABLE TRAY IS NOT INSTALLED/SPECIFIED. 2. CONDUIT SIZE ('X' FROM ABOVE); 2=1/2", 3=3/4", 4=1", 5=1-1/4", 6=1-1/2" 3. BLANK (NO LABEL) = 4-11/16" DEEP BOX WITH REQUIRED MUDRING AND 1" CONDUIT TO ABOVE NEAREST ACCESSIBLE CEILING/CABLE TRAY, TERMINATE WITH INSULATED THROAT BUSHING, PROVIDE PULL STRING. (UNLESS OTHERWISE NOTED) WALL/FLOOR ELECTRICAL PATHWAY SLEEVE; INSTALL THROUGH WALL OR FLOOR AS INDICATED. SLEEVES SHALL BE ABOVE ACCESSIBLE CEILINGS IN ACCESSIBLE LOCATION, FIELD VERIFY EXACT LOCATION TO AVOID CONFLICT WITH OTHER TRADES AND UTILITIES. IF WALL/FLOOR IS NOT FIRE RATED E.C. MAY UTILIZED EMT CONDUIT SLEEVES OF EQUAL SIZE. REFER TO ARCHITECTURAL DRAWINGS FOR FIRE RATINGS. (qty) = QUANTITY OF SLEEVES AT LOCATION EP2 = 2" HILTI SPEED SLEEVE CP-653-BA EP4 = 4" HILTI SPEED SLEEVE CP-653-BA ### FB# _D-X ELECTRICAL FLOORBOX REFER TO "ELECTRICAL FLOORBOX SCHEDULE" FOR INFORMATION. _= # OF DATA CABLES, X=CONDUIT SIZE (SEE NOTES 1,2,3 BELOW) TV AND/OR AV BOX; WITH POWER, DATA AND/OR AV CONNECTIVITY ### = BOX ID: REFER TO "ELECTRICAL AV/TV BOX SCHEDULE" FOR INFORMATION. _= # OF DATA CABLES, X=CONDUIT SIZE (SEE NOTE #2 BELOW) INSTALL CONDUIT (SIZE AS INDICATED) FROM BOX TO NEAREST ACCESSIBLE CEILING SPACE W/ DATA CABLING/TERMINATIONS AS INDICATED ON DRAWINGS. WALL ### FLOOR (qty) (qty) P 1PH 2/C 3/C 3P 3PH 3W 4W AC ADA AFF AFG AIC AL A or AMP ANN AP ATS AV AWG BFG C CATV CB CCTV CKT C CP CT CU DS EA E.C. EM EMT ENT EPO EQUIP EX FA FACP FLA FMC GND G.C. GEN GFI GFP HD HID HOA HP HPS HV HZ IG IMC J-BOX ABBREVIATIONS SINGLE POLE SINGLE-PHASE TWO-CONDUCTOR THREE-CONDUCTOR THREE POLE THREE-PHASE THREE-WIRE FOUR-WIRE ABOVE COUNTER AMERICANS WITH DISABILITIES ACT ABOVE FINISHED FLOOR ABOVE FINISHED GRADE AMPERE INTERRUPTING CAPACITY ALUMINUM AMPERE ANNUNCIATOR ACCESS POINT (WIRELESS DATA) AUTOMATIC TRANSFER SWITCH AUDIO VISUAL AMERICAN WIRE GAGE BELOW FINISHED GRADE CEILING MOUNTED CABLE TELEVISION CIRCUIT BREAKER CLOSED CIRCUIT TELEVISION CIRCUIT CONDUIT CONTROL PANEL CURRENT TRANSFORMER COPPER DISCONNECT SWITCH EACH ELECTRICAL CONTRACTOR EMERGENCY ELECTRICAL METALLIC TUBING ELECTRICAL NONMETALLIC TUBING EMERGENCY POWER OFF EQUIPMENT EXISTING FIRE ALARM FIRE ALARM CONTROL PANEL FULL LOAD AMPS FLEXIBLE METAL CONDUIT GROUND GENERAL CONTRACTOR GENERATOR GROUND FAULT CIRCUIT INTERRUPTER GROUND FAULT PROTECTION HEAVY DUTY HIGH INTENSITY DISCHARGE HAND-OFF-AUTOMATIC HORSE POWER HIGH PRESSURE SODIUM HIGH VOLTAGE HERTZ ISOLATED GROUND INTERMEDIATE METAL CONDUIT JUNCTION BOX V KVA kW kWh LED LFMC LFNC LTG LV MAX M.C. MCA MCB MCC MDP MH MIN MLO MOCP NA NC NEC NEMA NFPA NIC NL NO NTS OC OH DR OL PB P PNL PT PTZ QTY RCP RMC RNC SCA SCBA SF SPD SPEC SWBD SWGR TL TP TTB TV TYP UG UPS V VA V.I.F. VFD WAP W/ W/O WP XFMR KILOVOLT KILOVOLT AMPERE KILOWATT KILOWATT HOUR LIGHT EMITTING DIODE LIQUID TIGHT FLEXIBLE METAL CONDUIT LIQUID TIGHT FLEXIBLE NONMETALLIC CONDUIT LIGHTING LOW VOLTAGE MAXIMUM MECH. CONTRACTOR MINIMUM CIRCUIT AMPS MAIN CIRCUIT BREAKER MOTOR CONTROL CENTER MAIN DISTRIBUTION PANEL MANHOLE MINIMUM MAIN LUGS ONLY MAXIMUM OVERCURRENT PROTECTION NOT APPLICABLE NORMALLY CLOSED NATIONAL ELECTRICAL CODE NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION NATIONAL FIRE PROTECTION ASSOCIATION NOT IN CONTRACT NIGHT LIGHT NORMALLY OPEN NOT TO SCALE ON CENTER OVERHEAD DOOR OVERLOAD PUSHBUTTON PHASE PANEL POTENTIAL TRANSFORMER PAN/TILT/ZOOM QUANTITY REFLECTED CEILING PLAN RIGID METAL CONDUIT RIGID NONMETALLIC CONDUIT SHORT CIRCUIT AMPS STANDARD COLOR BY ARCHITECT SQUARE FOOT (FEET) SURGE PROTECTION DEVICE SPECIFICATION SWITCHBOARD SWITCHGEAR TWIST LOCK TWISTED PAIR TELEPHONE TERMINAL BOARD TELEVISION TYPICAL UNDERGROUND UNINTERRUPTIBLE POWER SUPPLY VOLTS VOLT AMPERE VERIFY IN FIELD VARIABLE FREQUENCY DRIVE WIRELESS ACCESS POINT WITH WITHOUT WEATHERPROOF TRANSFORMER A. E.C. SHALL REFER TO THE MECHANICAL DRAWINGS FOR EXACT LOCATIONS OF ALL MECHANICAL EQUIPMENT AND ELECTRICAL CONNECTIONS. B. E.C. SHALL PROVIDE MINIMUM WORKING CLEARANCE AS PER NEC BEFORE INSTALLING ANY ELECTRICAL PANELS OR CABINETS. SEE ELECTRICAL EQUIPMENT CLEARANCE DETAIL. C. INSTALL ALL LIGHT FIXTURES IN MECHANICAL ROOM AFTER THE MECHANICAL EQUIPMENT IS IN PLACE. ADJUST AS NECESSARY. PROVIDE CHAIN SUSPENSION KITS AS REQUIRED. D. REFER TO ARCHITECTURAL REFLECTED CEILING PLAN(S) FOR EXACT FIXTURE LOCATIONS, CEILING TYPES, ETC. E. E.C. SHALL PROVIDE ALL CONCRETE PADS AS REQUIRED FOR ALL ELECTRICAL EQUIPMENT. F. CONFIRM EXACT LOCATIONS OF ALL TELEPHONE/DATA OUTLETS WITH OWNER PRIOR TO ROUGH-IN. G. LOCATE SWITCHES, OUTLETS, ETC., SHOWN AT ROOM ENTRY DOORWAYS, AS CLOSE TO DOOR FRAME AS POSSIBLE, SO AS NOT RO INTERFERE WITH ROOM CABINETS, ETC. H. SUPPORT ALL LIGHT FIXTURES INDEPENDENT OF CEILING. I. ELECTRICAL CONTRACTOR SHALL OBTAIN ALL APPLICABLE PERMITS FOR WORK AND PAY ASSOCIATED FEES. J. MAINTAIN 24" MIN. CLEARANCE FROM ALL COMMUNICATIONS CABLING AND ELECTRONIC BALLASTS. K. UNLESS SPECIFICALLY INDICATED OTHERWISE, E.C. SHALL COORDINATE WITH ANY SPECIAL SYSTEMS SUPPLIER/SHOP DRAWINGS; DENTAL, MEDICAL, KITCHEN, SPECIALIZED EQUIPMENT, ETC. FOR THE EXACT ROUGH-IN REQUIREMENTS FOR THEIR EQUIPMENT. ALSO UNLESS INDICATED OTHERWISE, THE E.C. TO BE RESPONSIBLE FOR FINAL ELECTRICAL CONNECTIONS TO ALL SPECIAL EQUIPMENT. L. ALL CONDUIT/RACEWAY/CABLES TO BE CONCEALED IN WALLS OR ABOVE CEILINGS. IF ANY SURFACE WORK IS NECESSARY, IT SHALL BE APPROVED BY THE ARCHITECT/ENGINEER PRIOR TO INSTALLATION. M. ELECTRICAL CONTRACTOR SHALL VISIT THE SITE PRIOR TO BID AND THOROUGHLY INVESTIGATE THE EXISTING CONDITIONS, AS THEY RELATE TO THE SCOPE OF WORK DESCRIBED. MAKE NECESSARY PROVISIONS IN THE BASE BID TO ADEQUATELY ACCOMMODATE THESE CONDITIONS. N. DATA CABLING SYSTEM PRE-INSTALLATION CONFERENCE: 1. E.C. SHALL SCHEDULE A MEETING A MINIMUM OF FIVE CALENDAR DAYS PRIOR TO BEGINNING DATA CABLING INSTALLATION . ATTENDEES SHOULD INCLUDE OWNER’S REP., ENGINEER, GC, EC AND CABLING SUB. REFER TO SECTION 26 6210(1.4)(E) FOR ADDITIONAL INFORMATION. PROJECT GENERAL NOTES: IDAHO POWER CO. ROCKY MOUNTAIN POWER CO. WWW.IDAHOPOWER.COM WWW.ROCKYMOUNTAINPOWER.NET CONTACT: CONTACT: SHELLEY MARTIN (208) 388-5872 DAN KUHL (503) 308-0233 OR DAN KUHL (503) 308-0233 dan.kuhl@evergreen-efficiency.com dan.kuhl@evergreen-efficiency.com UTILITY LIGHTING REBATES & INCENTIVES: IT SHALL BE THE RESPONSIBILITY OF THE ELECTRICAL CONTRACTOR TO PREPARE ALL REQUIRED APPLICATIONS AND INFORMATION REQUIRED TO PROVIDE THE OWNER WITH THE MAXIMUM AMOUNT OF REBATE DOLLARS FROM THE LOCAL UTILITY COMPANY. THE ELECTRICAL CONTRACTOR SHALL SUBMIT VERIFICATION OF THE UTILITY COMPANY PRE-APPLICATION APPROVAL PRIOR TO ORDERING ANY MATERIALS. VISIT THE FOLLOWING UTILITY CO. WEBSITES FOR INFORMATION: TYPICAL DEVICE MOUNTING HEIGHTS: GENERAL COORDINATION NOTE: GENERAL DETAIL NOTES: FINISH FLOOR 1' - 6'' THERMOSTAT OR SENSORVERIFY WITH M.C. PRIOR TO LIGHT SW. (OR AS NOTED) * 4' - 0'' * 3' - 6'' (OR AS NOTED) RECEPTACLE @ MILLWORK BACKSPLASH CA B . D I M E N S I O N S PE R A R C H . D E T A I L 6" CABINET * E.C. SHALL COORDINATE ALL DEVICE MOUNTING HGTS. AND EXACT LOCATION WITH ARCHITECTURAL INTERIOR ELEVATIONS REPORT CONFLICTS TO ARCHITECT **PRIOR TO ROUGH-IN** ROUGH-IN. TYPICAL FOR ALL DEVICES MOUNTED ABOVE COUNTER (ie C.O.'S, DATA, PHONE etc.) A. B. C. D. ALL MOUNTING HEIGHTS TYPICAL UNLESS NOTED OTHERWISE. COORDINATE OUTLET HEIGHTS WITH ARCHITECTS MILLWORK DWGS. TO INSURE THAT OUTLETS WILL NOT FALL BEHIND CABINETS, BACKSPLASHES, OR INTERFERE WITH WAINSCOTING, ETC. ALL SWITCHES AND THERMOSTATS TO BE MOUNTED AS CLOSE TO DOOR JAMS AS POSSIBLE. COORDINATE ALL DEVICES WITH ARCHITECTURAL PLANS AND DETAILS. COORDINATE LIGHT SWITCH & OUTLET HEIGHTS WITH ARCHITECTURAL WAINSCOTING AND OR TILE WORK SO AS NOT TO FALL MIDWAY IN THESE FINISHES. FIRE 6' - 8'' FIRE ALARM NOTIFICATION DEVICE FIRE MANUAL PULL STATION HANDLE SHALL BE BETWEEN 42" & 48" AFF CABINET RECEPT. TELE/DATA OUTLET TV OUTLET ELECTRICAL EQUIP. CLEARANCE ELECTRICALEQUIPMENT NO T E # 1 N O T E #4 NOTE#3 NOTE#2 NOTES: 1. THE MINIMUM HEADROOM OF WORKING SPACE SHALL BE 6 1/2FT. 2. THE WIDTH OF THE WORKING SPACE SHALL BE THE WIDTH OF THE EQUIPMENT OR 30", WHICHEVER IS GREATER. THE PANEL DOOR SHALL OPEN AT LEAST 90 DEGREES. 3. ALL CIRCUIT BREAKERS, WHEN IN THIER HIGHEST POSITION, SHALL NOT BE MORE THAN 6FT 7 IN. ABOVE THE FINISHED FLOOR. 4. 3FT CLEARANCE IF 0-150V TO GROUND, 3.5FT CLEARANCE IF 151-600V TO GROUND. 4FT IF EXPOSED LIVE PARTS ON BOTH SIDES OF THE WORKING SPACE. GENERAL NOTES: A. ALL WORKING SPACE CLEARANCES ARE FROM THE FACE OF THE EQUIPMENT. 13053 STATEOFIDAHOSHAWNA.M E A D ORREGISTEREDRP OFESSIONALENGIN EE R 1823 E. Center Pocatello, Idaho 83201 tel (208) 232-4439 www.payneengineeringinc.com Engineering Inc. Consulting Engineers BO O T H Date Sheet No. A r c h i t e c t u r e (2 0 8 ) 2 3 3 - 4 5 4 8 Ph o n e Po c a t e l l o , I d a h o 8 3 2 0 1 34 0 E a s t C l a r k S t r e e t , S u i t e A (2 0 8 ) 2 3 3 - 0 2 6 3 te d @ b o o t h a r c h i t e c t u r e . c o m Fa x em a i l P L L C Ne w B u i l d i n g f o r : P.E. #:2265 7/20/22 Re v i s i o n s ELECTRICAL SYMBOLS & DETAILS Mo u n t a i n W e s t 07-20-2022 TB D Re x b u r g , I d a h o E0.0 SCALE: NONEARECEPTACLE MOUNTING DETAIL nLIGHT CONTROL SYMBOL SCHEDULE SYMBOL DESCRIPTION nLIGHT CEILING MOUNTED SENSOR, SEE nLIGHT SYSTEM SCHEDULE FOR ADDITIONAL INFORMATION.S n## n##B nLIGHT BACKBONE DEVICE, SEE nLIGHT SYSTEM SCHEDULE FOR ADDITIONAL INFORMATION. n##R nLIGHT RELAY/POWER PACK DEVICE, SEE nLIGHT SYSTEM SCHEDULE FOR ADDITIONAL INFORMATION. n##RP nLIGHT RELAY PANEL, SEE nLIGHT SYSTEM SCHEDULE FOR ADDITIONAL INFORMATION. nLIGHT SWITCH MOUNTED DEVICE, SEE nLIGHT SYSTEM SCHEDULE FOR ADDITIONAL INFORMATION. n## GREEN, CAT-5e PATCH CABLE (LENGTH AS REQUIRED), PLENUM RATED. • CABLE SHALL BE INSTALLED IN 3/4" CONDUIT WHERE IT CANNOT BE INSTALLED IN AN ACCESSIBLE CEILING SPACE. • PROVIDE A MINIMUM OF 2FT SLACK BETWEEN ALL DEVICES AND FIXTURE CONNECTION POINTS. 0-10V DIMMING WIRING, UTILIZE 1/2" CONDUIT WITH (2) #18 AWG. VIOLET FOR POSITIVE, GREY FOR NEGATIVE 1. E.C. SHALL BE RESPONSIBLE FOR PROVIDING ALL LIGHTING CONTROL COMMISSIONING/PROGRAMMING OF ALL nLIGHT COMPONENTS. THE COMMISSIONING/PROGRAMMING SHALL BE DONE BY A nLIGHT CERTIFIED TECHNICIAN. 2. E.C. SHALL NOTIFY OWNER 1-WEEK PRIOR TO COMMISSIONING/PROGRAMMING OF THE SYSTEM SO THAT THE OWNER CAN PROVIDE REPRESENTATIVES DURING THE COMMISSIONING/PROGRAMMING PERIOD. GENERAL LIGHTING NOTES: NOTE: ALL SYMBOLS MAY NOT BE USED SCALE: NONEBRECESSED LIGHT FIXTURE DETAIL No. Description Date FE SCPC WP1 WP1 SCD1 SCD1 SCD1 D1 D2 D2 D2 D2SCD2 S CD2 n4 n4 n4 n4 WD D D1 D1 n1 S CD1 D1 SCD7 1 2 3 4 5 6 7 8 9 10 A B C D (TYP)F4 RR BREAK SERVICE MANAGER SERVICE RR OFFICE PARTS LOBBY GALLERY SHOP F5 F5 NLF1E F1 NLF1E F1 (TYP)F1 (TYP)F1 F6E F6E (TYP)F7 FX1 FX2 FX2 FX1 FX1 FX1 FX1 F6 F6 F7E F7E F7E F6E F6 F6 (TYP)F7 'LA' 'LCP'F3E F3E F3E F3E F3E F3E F3E (TYP)F3 F3E F3E F3E F3E F3E (TYP)F3 (TYP)F3 TO 'LPC' LA-1 1 LA-3 #8's 1 LA-5 #8's 1 LA-13 LA-13 LA-13 LA-13 LA-13 LA-13 LA-13 (TYP)F8 (TYP)F8 F8 (TYP)F8 (TYP)F9 LA-13 LA-13 TO 'LPC' LA-7 1 LA-9 1 F10E 11' -6" F10E 11' -6" F10E 11' -6"FX3 FX3 FX3 F11 18' -0" F11 18' -0" F11 18' -0" F11 18' -0" F11 18' -0" F11 18' -0" F11 18' -0" LA-111 LA-11 LA-11 LA-11 LA-11 LA-11 LA-11 LA-11LA-11LA-11 3 4 A B C D UPPER OFFICE STORAGE F1F1EF1 (TYP)F2 (TYP)F2 LA-15 LA-15 LA-15 AIRCRAFT CABLE "Y" HANGER (TYP BOTH ENDS OF FIXTURE" AIRCRAFT CABLE ANCHORED SECURELY TO STRUCTURE ABOVE LEVEL W/ BOTTOM OF TRUSSES 13053 STATEOFIDAHOSHAWNA.M E A D ORREGISTEREDRP OFESSIONALENGIN EE R 1823 E. Center Pocatello, Idaho 83201 tel (208) 232-4439 www.payneengineeringinc.com Engineering Inc. Consulting Engineers BO O T H Date Sheet No. A r c h i t e c t u r e (2 0 8 ) 2 3 3 - 4 5 4 8 Ph o n e Po c a t e l l o , I d a h o 8 3 2 0 1 34 0 E a s t C l a r k S t r e e t , S u i t e A (2 0 8 ) 2 3 3 - 0 2 6 3 te d @ b o o t h a r c h i t e c t u r e . c o m Fa x em a i l P L L C Ne w B u i l d i n g f o r : P.E. #:2265 7/20/22 Re v i s i o n s LIGHTING PLANS Mo u n t a i n W e s t 07-20-2022 TB D Re x b u r g , I d a h o E1.0 A. REFER TO SYMBOL SCHEDULE SHEET FOR PROJECT GENERAL NOTES AND GENERAL NOTES ASSOCIATED WITH THE INSTALLATION OF EACH SYSTEM, INCLUDINB BUT NOT LIMITED TO; LIGHTING, POWER, FIRE ALARM, SPECIAL SYSTEMS, ETC. GENERAL NOTES: KEY NOTES:# 16'8'0"SCALE: 1/8" = 1'-0"1 MAIN FLOOR LIGHTING PLAN LIGHTING FIXTURE SCHEDULE TYPE DESCRIPTION MOUNTING VOLTAGE LUMENS COLOR TEMP.(K) MFGR.CATALOG # APPROVED MFGR'S NOTES F1 2X2 LED FLAT PANEL, 0-10V DIMMING, FIELD SWITCHABLE RECESSED 120-277 MED 4000 LITHONIA CPX 2X2 AL07 M4 COOPER 1 F1E 2X2 LED FLAT PANEL,0-10V DIMMING, FIELD SWITCHABLE, EMERG. BATTERY PACK RECESSED 120-277 MED 4000 LITHONIA CPX 2X2 AL07 M4 IE10WCP COOPER 1 F2 HIGHBAY LED, AIRCRAFT CABLE SUSPENSION SUSPENDED 120-277 15000 4000 LITHONIA IBG-15000LM-SEF-PFL-GND-MVOLT-GZ10-40K-80CRI-SCBA-IBGACVH COOPER 1,3 F3 HIGHBAY LED, AIRCRAFT CABLE SUSPENSION SUSPENDED 30FT AFF 120-277 24000 4000 LITHONIA IBG-24000LM-SEF-PFL-GND-MVOLT-GZ10-40K-80CRI-SCBA-IBGACVH COOPER 1,3 F3E HIGHBAY LED, AIRCRAFT CABLE SUSPENSION, EM. BATTERY PACK SUSPENDED 30FT AFF 120-277 24000 4000 LITHONIA IBG-24000LM-SEF-PFL-GND-MVOLT-GZ10-40K-80CRI-SCBA-E10WCP-IBGACVH COOPER 1,3 F4 6" ROUND RECESSED LED CAN, 0-10V DIMMING RECESSED 120-277 2000 4000 LITHONIA LDN6-40/20-LO6AR-LSS-MVOLT-EZ10 COOPER 1 F5 4FT LED SURFACE WRAPAROUND FIXTURE SURFACE 120-277 4000 4000 LITHONIA FML4W 48 AL06 SEF 840 MVOLT COOPER F6 8FT LED STRIP, 0-10V DIMMING SURFACE OR SUSPENDED 120-277 8000 4000 LITHONIA CLX-L96-8000LM-SEF-RDL-MVOLT-GZ10-40K-80CRI COOPER F6E 8FT LED STRIP, 0-10V DIMMING, W/ EM BATTERY PACK SURFACE OR SUSPENDED 120-277 8000 4000 LITHONIA CLX-L96-8000LM-SEF-RDL-MVOLT-GZ10-40K-80CRI-PS1050 COOPER F7 4FT LED STRIP, 0-10V DIMMING SURFACE/ SUSPENDED 120-277 4000 4000 LITHONIA CLX-L48-4000LM-SEF-RDL-MVOLT-GZ10-40K-80CRI COOPER F7E 4FT LED STRIP, 0-10V DIMMING SURFACE/ SUSPENDED 120-277 4000 4000 LITHONIA CLX-L48-4000LM-SEF-RDL-MVOLT-GZ10-40K-80CRI-PS1050 COOPER F8 PENDANT LINEAR LED, AIRCRAFT CABLE SUSPENSION, 0-10V DIMMING SUSPENDED 12FT AFF 120-277 1250LM/FT 4000 FOCAL POINT LTG FSM4LS-FL-1250LF-40K-1C-UNV-LD1-C96**-SCBA-(PER DWG'S) COOPER 1,2,3,4 F9 PENDANT LINEAR LED, AIRCRAFT CABLE SUSPENSION, 0-10V DIMMING SUSPENDED 12FT AFF 120-277 375LM/FT 4000 FOCAL POINT LTG FSM4LS-FL-375LF-40K-1C-UNV-LD1-C96**-SCBA-(PER DWG'S) COOPER 1,2,3,4 F10E EXTERIOR LED WALL PACK, EMERG. BATTERY PACK WALL 120-277 4500 4000 LITHONIA WDGE2 LED-P4-40K-80CRI-VW-MVOLT-E20WC-SCBA COOPER 3 F11 EXTERIOR LED WALL PACK WALL 120-277 18000 4000 LITHONIA WDGE4 LED-P3-40K-80CRI-R3-MVOLT-SCBA COOPER 3 FX1 EXIT SIGN W/ 90MIN BATTERY,THERMOPLASTIC, GREEN LED, SINGLE/DOUBLE FACE WALL OR CEILING 120-277 N/A N/A LITHONIA LQM-S-W-3-G-20/277-EL N COOPER FX2 EXIT SIGN/EM LIGHT COMBO W/ 90MIN BATTERY,THERMOPLASTIC, GREEN LED, SINGLE/DOUBLE FACE WALL OR CEILING 120-277 N/A N/A LITHONIA LHQM LED-G-SD COOPER FX3 WALL MOUNTED EXTERIOR EMERGENCY EGRESS LIGHT, W/HEATER WALL ABOVE DOOR 120-277 N/A N/A LITHONIA AFF-OEL-SCBA-UVOLT-LTP-SDRT-WT-CW DUAL-LITE LIGHTING CONTROL/OCCUPANCY SENSOR SCHEDULE TYPE DESCRIPTION MFGR. CATALOG # NOTES APPROVED EQUALS DIMMER SWITCHES - LINE VOLTAGE D1 LINE VOLTAGE 0-10V DIMMER, ON/OFF/DIMMING PUSH-BUTTONS SENSOR SWITCH sPODMRA-D-** 2,3,4 D2 LINE VOLTAGE 0-10V DIMMER FOR MULTI-WAY OPERATION, ON/OFF/DIMMING PUSH-BUTTONS SENSOR SWITCH sPODMRA MWO-D-** 2,3,4 LIGHTING CONTROL PANELS 'LCP' SURFACE MOUNTED, 8-RELAY DIGITAL RELAY PANEL, W/nLIGHT INTERFACE ACUITY BRANDS ARP INTENC08 NLT/8SPR/MVOLT/SC/SM/DTC 6 COOPER, WATTSTOPPER, LEVITON nLIGHT DEVICES n1 nLIGHT ON/OFF PUSHBUTTON SENSOR SWITCH nPODM 3 n4 nLIGHT ON/OFF PUSHBUTTON, 4-CHANNEL SENSOR SWITCH nPODM-4P 3 OCC. SENSORS - CEILING (LINE VOLTAGE) CD2 DUAL-TECHNOLOGY, LINE VOLTAGE, SMALL MOTION 800W MAX LOAD SENSOR SWITCH CMR PDT 9 COOPER, WATTSOPPER, HUBBELL OCC. SENSORS - CEILING (LOW VOLTAGE) CD1 DUAL-TECHNOLOGY, SMALL MOTION 360 DEGREE COVERAGE, LOW VOLTAGE, W/ISOLATED RELAY SENSOR SWITCH CM PDT 9 R 1 COOPER, WATTSTOPPER, HUBBELL CD7 DUAL-TECHNOLOGY, CORNER MOUNT WIDE VIEW, LOW VOLTAGE, W/ISOLATED RELAY SENSOR SWITCH WV PDT 16 R (KIT) 1 COOPER, WATTSTOPPER, HUBBELL CPC ON/OFF & AUTOMATIC DIMMING PHOTOCELL SENSOR SWITCH CM PC ADC 1 COOPER, WATTSTOPPER, HUBBELL OCC. SENSORS - WALL MOUNTED WDD DUAL-TECHNOLOGY, 0-10V DIMMING SENSOR SWITCH WSX-PDT-D 2,5 COOPER, WATTSTOPPER, HUBBELL WP1 PASSIVE-INFRARED, 1-POLE, NEUTRAL REQUIRED SENSOR SWITCH WSX-** 2 COOPER, WATTSTOPPER, HUBBELL SCALE: 1/8" = 1'-0"2 MEZZANINE FLOOR LIGHTING PLAN 16'8'0" 1 ROUTE CIRCUIT THROUGH LIGHTING CONTROL PANEL (LCP); REFER TO LIGHTING CONTROL/OCCUPANCY SENSOR SCHEDULE FOR ADDITIONAL INFORMATION. PROVIDE ADDITIONAL UN-SWITCH LEG AS NEEDED FOR CONNECTION TO BATTERY PACK OF EMERGENCY FIXTURE(S) (F#E). 1. PROVIDE ADDITIONAL POWER PACKS; SENSOR SWITCH PP20 AS NEED FOR QTY OF OCCUPANCY SENSORS/SWITCHES. 2. DEVICE COLOR SHALL MATCH WIRING DEVICES; REFER TO SPECIFICATIONS. 3. REFER TO MANUFACTURER DOCUMENTATION FOR QTY AND SIZE OF CONDUCTORS BETWEEN LOW VOLTAGE SWITCH, SENSOR(S) AND POWER/RELAY PACKS. 4. PROVIDE SECONDARY RELAY PACK; SENSOR SWITCH SP20 AS NEEDED TO PROVIDE DUAL-LEVEL SWITCHING OF FIXTURES. 5. PROVIDE 0-10V DIMMING CONDUCTORS (GRAY & VIOLET) BETWEEN SWITCH AND LIGHT FIXTURES FOR DIMMING CONTROL. 6. PROGRAM ON/OFF TIMES OF RELAY'S AS DIRECTED BY OWNER. PROVIDE COMMISSIONING AS INDICATED IN GENERAL NOTES BELOW. 7. CUSTOM WALL STATION ENGRAVINGS IS REQUIRED FOR WALL STATION(S) AND SHALL BE SPECIFIED/COORDINATED WITH OWNER AFTER PROGRAMING OF SYSTEM. CONTROL & OCCUPANCY SENSOR SCHEDULE NOTES: • E.C. SHALL BE RESPONSIBLE FOR THE PROGRAMMING/COMMISSIONING OF THE LIGHTING CONTROL SYSTEMS TO FUNCTION AS INDICATED ON THE DRAWINGS AND SHALL INCLUDE ALL REQUIRED COST IN THE BASE BID. FOR AREAS WITH DAYLIGHTING CONTROL, THE DAYLIGHTING SET-POINTS SHALL BE COORDINATED WITH THE OWNER FOR EACH AREA PRIOR TO FINAL PROGRAMMING OF THE DAYLIGHTING SENSOR(S). ALL PROGRAMMING/COMMISSIONING SHALL BE DONE BY A FACTORY CERTIFIED OR TRAINED PERSON. GENERAL LIGHTING CONTROL NOTES: 1. REFER TO DRAWINGS FOR FIXTURES REQUIRED TO HAVE 0-10V OR STEP-LEVEL DIMMING CONTROL. PROVIDE FIXTURE(S) WITH LED DRIVER(S) AND REQUIRED DIMMING/SWITCH-LEG CONDUCTORS BETWEEN SWITCH(ES) AND FIXTURE(S) TO PROVIDE CONTROL AS INDICATED ON DRAWINGS. 2. FIXTURE LENGTH AS INDICATED ON DRAWINGS. 3. SCBA - STANDARD COLOR BY ARCHITECT/OWNER (COORDINATE COLOR WITH ARCHITECT/OWNER PRIOR TO ORDERING.) 4. FIELD ADJUST PENDANT LENGTH AS REQUIRED, VERIFY LENGTH WITH OWNER. LIGHT FIXTURE SCHEDULE NOTES: • LIGHTING FIXTURES INDICATED IN SCHEDULE ARE BASIS OF DESIGN, ALTERNATE MANUFACTURERS SHALL BE PRE-APPROVED BY ADDENDUM. ALTERNATE MANUCATURERS SHALL SUBMIT PER- APPROVALS TO ENGINEER A MINIMUM OF 10 DAYS PRIOR TO PROJECT BID DATE. GENERAL LIGHTING SCHEDULE NOTES: SCALE: NONEALIGHT FIXTURE HIGHBAY MOUNTING DETAIL No. Description Date FE MM T MM T MM T MM T MM T MM T MM T MM T FB2F FB2F FF FP MM T MM T MM T MM T 1 2 3 4 5 6 7 8 9 10 A B C D WP WP WP WP WP WP WP WPWPWPWP WP 1 1 1 1 1111 2 'MDP''LA' 'LB' 'LC' 3 'TTB' WPWPWP 4 (A/E2.0) 5 5 5 5 5 6 6 5 5 5 7 1"C 1"C 42" EWC RR BREAK SERVICE MANAGER SERVICE RR OFFICE PARTS LOBBY GALLERY SHOP 42" AC 48"48"48"48"48"48" 48" 48" 48"48"48"48"48"48" 48" 48" 48" 48" 48" W W WP AIR COMPRESSOR 60 A/NEMA 3R 8 BRIDGE CRANE 60 A/NEMA 1 8 99 CU-1 CU-2 CU -3 LB-14 LB-16#10's LC-14#10's LC-12 LC-10#10's LB-12#10'sLB-18#10's LA-27 LA-17 LA-16 LA-12 LA-12 LA-10 LA-10 LA-10 LA-12 LA-12 LA-14LA-14 LA-12 LA-16 LA-16 LA-18 LA-10 LA-8 LA-8 LA-8 LA-8 LA-28 LA-28 LA-28 LA-12 LA-8 LA-18 LA-18 LA-18 LA-18 LA-20 LA-24 LA-22 LA-6 LA-6 LA-6 LA-20 LA-6 LA-6 LA-20LA-20 LA-22 LA-22 LA-20 LA-24 LA-24 LA-24LA-24 LA-26 LA-22 LA-2LA-2LA-4LA-4LA-6LA-8 LA-10 LA-25 LA-16 LA-24 LA-23 LA-26 LB-2 LB-6 LB-37,39,41#6's LB-6 LB-6 LB-8 LB-8 LB-8 LB-10 LB-10 LB-10 LC-8 LC-8 LC-8 LC-8 LC-6 LC-40,42#6's LC-6 LC-36,38#6's LC-4LC-2 LC-37,39,41#6's LC-2 LC-2 LC-2LB-4 LB-4 LB-4LB-2 LB-2 10 AHU-1 HVLS-1 HVLS-2 MOTORIZED DAMPER LB-8 CONTROL AS DIRECTED BY MECH. CONTRACTOR MOTORIZED DAMPER LB-2 CONTROL AS DIRECTED BY MECH. CONTRACTOR PTAC-1 LA-26 CH-1 CH -2 3 4 A B C D UPPER OFFICE STORAGE WH-1 LA-51,53#10's LA-19 LA-19 LA-19 LA-19 LA-21LA-21 LA-21 LA-21 LA-21 LA-21 F-1 F-2 F-3 CP-1 LA-19 UH-1 LA-19 PTAC-2 6" 3/4" C., 1#6 B.C. GRND. CONNECT TO BLDG. GROUND SYSTEM FINISH FLOOR TYPICAL CONDUITS OUT TO VOICE/ DATA OUTLETS. SEE PLAN FOR SIZE, ETC. (TYPICAL TOP & OR BOTTOM OF BOARD) 4'X8'X3/4" PLYWOOD PRIME & PAINT W/TWO COATS GREY ENAMEL (INSTALL ON WALLS AS INDICATED ON PLANS) ANCHOR SECURELY TO WALL W/ CONST. ADHESIVE. DOUBLE-DUPLEX OUTLET(S) PER PLANS 120V CIRCUIT PER PLANS PULL CORD INCOMING UTILITY SERVICECONDUIT(S) WITH INSULATED BUSHING. SEE SITE PLAN FOR SIZE & QTY GROUND BAR (SQ. D #PK27GTA) COMM. UTILITY CO. EQUIPMENT INSTALL INSULATED BUSHING ON ALL CONDUIT ENDS. TYP TOP & BOTTOM UNISTRUT ANCHOR TYP TOP & BOTTOM WALL MOUNTED RACK ORTRONICS# OR-604045451 13053 STATEOFIDAHOSHAWNA.M E A D ORREGISTEREDRP OFESSIONALENGIN EE R 1823 E. Center Pocatello, Idaho 83201 tel (208) 232-4439 www.payneengineeringinc.com Engineering Inc. Consulting Engineers BO O T H Date Sheet No. A r c h i t e c t u r e (2 0 8 ) 2 3 3 - 4 5 4 8 Ph o n e Po c a t e l l o , I d a h o 8 3 2 0 1 34 0 E a s t C l a r k S t r e e t , S u i t e A (2 0 8 ) 2 3 3 - 0 2 6 3 te d @ b o o t h a r c h i t e c t u r e . c o m Fa x em a i l P L L C Ne w B u i l d i n g f o r : P.E. #:2265 7/20/22 Re v i s i o n s POWER/DATA PLANS Mo u n t a i n W e s t 07-20-2022 TB D Re x b u r g , I d a h o E2.0 A. REFER TO SYMBOL SCHEDULE SHEET FOR PROJECT GENERAL NOTES AND GENERAL NOTES ASSOCIATED WITH THE INSTALLATION OF EACH SYSTEM, INCLUDINB BUT NOT LIMITED TO; LIGHTING, POWER, FIRE ALARM, SPECIAL SYSTEMS, ETC. GENERAL NOTES: KEY NOTES:# SCALE: 1/8" = 1'-0"1 MAIN FLOOR POWER/DATA PLAN 16'8'0" 1 CONNECTION TO OVERHEAD DOOR MOTOR, COORDINATE CONNECTION WITH EQUIPMENT PRIOR TO ROUGH-IN. PROVIDE CONDUIT AND CONDUCTORS TO PUSH-BUTTON STATION PER MANUFACTURERS REQUIREMENTS. 2 CT CAN AND METER BASE MOUNTED ON BUILDING. SEE POWER RISER FOR ADDITIONAL INFORMATION. 3 NEW UNDERGROUND SECONDARY; SEE POWER RISER FOR ADDITIONAL INFORMATION. 4 (1) 4" CONDUIT FOR TELECOMMUNICATIONS SERVICE TO BUILDING AND (1) 2" CONDUIT FOR CABLE TV SERVICE TO BUILDING. STUB CONDUITS TO LOCATIONS AS SPECIFIED BY LOCAL TELEPHONE AND CABLE TV PROVIDERS, PROVIDE WITH PULL-STRING. COORDINATE WITH LOCAL UTILITIES AS INDICATED IN GENERAL NOTES 5 INSTALL RECEPTACLE WITHIN 18" OF THE TOP OF THE WINDOW IN ACCORANCE WITH NEC 210.62. 6 CONNECTION TO AUTOMATIC DOORS; FIELD VERIFY CONNECTION LOCATION AND REQUIREMENTS WITH EQUIPMENT INSTALLERS. PROVIDE ALL REQUIRED ROUGH-IN AND CONNECTIONS TO PUSH-BUTTONS IF APPLICABLE. 7 RECEPTACLE(S) AND DATA OUTLET(S) INSTALLED IN MILLWORK. E.C. SHALL ROUTE POWER AND DATA CONDUIT UNDERGROUND AND STUB-UP INTO MILLWORK. FIELD VERIFY EXACT STUP UP LOCATIONS WITH MILLWORK AND OWNER PRIOR TO ROUGH-IN. 8 FUSE DISCONNECT SWITCH PER EQUIPMENT NAMEPLATE. 9 CONNECT EXHAUST FAN TO ROOM LIGHTING CIRCUIT AND CONTROL WITH LIGHTING 10 PROVIDE AND INSTALL (2) 2" SPARE CONDUITS STUB OUT OF BULDING FOR FUTURE WASHBAY BUILDING AND MONUMENT SIGN. E.C. SHALL FIELD VERIFY STUB OUT LOCATION WITH OWNER AND G.C. PRIOR TO INSTALLATION. SCALE: 1/8" = 1'-0"2 MEZZANINE FLOOR POWER/DATA PLAN 16'8'0"SCALE: NONEATELEPHONE TERMINAL BOARD (TTB) DETAIL ELECTRICAL FLOORBOX SCHEDULE ID DESCRIPTION MFGR. FLOORBOX p/n COVERPLATE p/n POWER DEVICES DATA DEVICES NOTES FB2F 2-GANG, MULTI-SERVICE CONCRETE FLOORBOX, W/FLUSH STYLE RECTANGULAR COVER, 3" MIN. POUR HUBBELL CFB2G30CR 24GTCVRXXX (1) DUPLEX RECPT. PER OWNER 1,2,3 1. PROVIDE REQUIRED SUB-PLATES FOR INSTALLATION OF POWER, DATA AND AV DEVICES. 2. E.C. SHALL FIELD LOCATE EXACT PLACEMENT OF FLOORBOX WITH ARCHITECT/OWNER PRIOR TO INSTALLATION. 3. PROVIDE CONDUIT (SIZE AS INDICATED ON DRAWINGS) TO ACCESSIBLE CEILING SPACE FOR ROUTING OF DATA AND/OR LOW VOLTAGE CABLING. FLOORBOX SCHEDULE NOTES: SHOP SPECIAL NOTES: • ALL WIRING METHODS AND DEVICES LOCATED IN SHOP AND AREAS OPEN TO THE SHOP SHALL CONFORM TO NEC ARTICLE 511, SECTION 501.15 and 210.8(B). • ALL SURFACE RACEWAY INSTALLED BELOW 6'-0" AFF SHALL BE RIGID GALVANIZED STEEL CONDUIT. • PROVIDE AND INSTALL CONDUIT SEAL-OFFS TO COMPLY WITH NEC SECTION 511, 501.15 AND LOCAL AHJ. • WHERE PANELS ARE INSTALLED IN SHOP AREA, INSTALLATION SHALL BE IN COMPLIANCE WITH NEC ARCTICAL 511, SECTION 501.15, SECTION 240.24(A) AND LOCAL AHJ REQUIREMENTS. • ALL UNDERGROUND CONDUITS INSTALLED IN SHOP/LNG BAY AREAS SHALL BE INSTALLED IN COMPLIANCE WITH NEC ARTICLE 511 AND SECTION 501.15. FIRE ALARM SYSTEM SHALL BE DESIGN BUILD BY THE ELECTRICAL CONTRACTOR. PROVIDE AND INSTALL AS REQUIRED BY CURRENT ADOPTED INTERNATIONAL FIRE CODE AND LOCAL AHJ REQUIREMENTS. PROVIDE ALL DOCUMENTATION, DRAWINGS, VOLTAGE DROP AND BATTERY CALCULATIONS AND ECT. TO THE CITY FOR PERMITTING AND INSTALLATION. A. NFPA ALLOWS NOTIFICATION APPLIANCES TO BE MOUNTED AT A HEIGHT RANGE BETWEEN 80" TO 96" ABOVE FINISH FLOOR. THE PREFERRED HEIGHT IS 80". IF THIS CONFLICTS WITH OTHER TRADES OR ROOM FURNISHINGS, LOCATE AS CLOSE TO 80" AS POSSIBLE, NOT EXCEEDING 96". ALL NOTIFICATION APPLIANCES IN A COMMON ROOM OR LINE OF SIGHT SHALL BE LOCATED AT A COMMON HEIGHT. B. MOUNT PULL STATIONS AT 46-48" A.F.F. TO THE OPERATING HANDLE TO MEET ADA REQUIREMENTS. C. IN CORRIDORS, NOTIFICATION APPLIANCES MUST BE LOCATED WITHIN 15' FROM ENDS OF CORRIDORS AND A MAXIMUM OF 100' SPACING. D. PROVIDE THE REQUIRED CANDELA RATING OF ALL NOTIFICATION APPLIANCES ACCORDING TO ROOM SIZE,ETC. E. NOTIFICATION APPLIANCES TO BE SYNCHRONIZED TO PROVIDE A 3-3-3 TEMPORAL PATTERN. F. PROVIDE REQUIRED MONITORING OF FIRE SPRINKLER SYSTEM, COORDINATE WITH FIRE SPRINKLER CONTRACTOR. G. ALL HVLS (HIGH VOLUME LOW SPEED) FANS SHALL BE INTERCONNECTED TO FIRE ALARM SYSTEM AND SHUT-DOWN UPON ACTIVATION OF FIRE ALARM. FIRE ALARM SYSTEM DESIGN: MECHANICAL - FURNACE SCHEDULE EQUIP. ID VOLTS PH. HP FLA CIRCUIT FEEDER NOTES F-1 120 V 1 3/4 7 A LA-38 #12'S 1,4 F-2 120 V 1 1 9 A LA-40 #12'S 1,4 F-3 120 V 1 1/2 5 A LA-42 #12'S 1,4 MECHANICAL - CONDENSING UNIT SCHEDULE EQUIP. ID VOLTS PH. MCA MOCP CIRCUIT FEEDER DISCONNECT NOTES CU-1 208 V 1 32 A 50 A LA-44,46 #8'S 60 A/FUSED/3R 2,4 CU-2 208 V 1 35 A 60 A LA-48,50 #6'S 60 A/FUSED/3R 2,4 CU-3 208 V 1 26 A 40 A LA-52,54 #8'S 60 A/FUSED/3R 2,4 1. E.C. SHALL PROVIDE LOCAL DISCONNECT RATED, THERMAL-OVERLOAD SWITCH FOR EQUIPMENT; SWITCH RATING SHALL NOT BE LESS THEN CIRCUIT BREAKER SUPPLYING EQUIPMENT. 2. E.C. SHALL PROVIDE LOCAL DISCONNECT SWITCH FOR EQUIPMENT; SIZE AND TYPE AS INDICATED IN SCHEDULE. IF FUSED DISCONNECT IS SPECIFIED FOR EQUIPMENT, FUSE PER EQUIPMENT NAMEPLATE RATING. 3. EQUIPMENT IS FACTORY SUPPLYED WITH DISCONNECT AND CONVIENENCE OUTLET; E.C. SHALL PROVIDE ALL NECESSARY CONNECTIONS. 4. PROVIDE 1/2" CONDUIT AND CONDUCTORS BETWEEN FURNACE AND CORRESPONDING OUTDOOR CONDENSING UNIT. COORDINATE SIZE AND NUMBER OF CONDUCTORS WITH M.C. PRIOR TO ROUGH-IN. PROVIDE CONNECTION BETWEEN FURNACE AND ASSOCIATED OUTSIDE AIR MOTORIZED DAMPER, COORDINATE WITH M.C. 5. E.C. SHALL INTERLOCK FAN WITH FIRE ALARM SYSTEMS, FAN SHALL DE-ENERGIZED UPON ACTIVATION OF FIRE ALARM SYSTEM, COORDINATE WITH M.C. AND FIRE ALARM INSTALLER. MECHANICAL SCHEDULE NOTES: MECHANICAL - AIR HANDLING UNIT SCHEDULE EQUIP. ID VOLTS PH. HP FLA CIRCUIT FEEDER NOTES AHU-1 208 V 3 3 12 A LC-31,33,35 #12'S 3 MECHANICAL - CEILING FAN SCHEDULE EQUIP. ID VOLTS PH. FLA CONTROL CIRCUIT FEEDER NOTES HVLS-1 208 V 3 6 A WIRELESS CONTROLLER LB-32,34,36 #12'S 5 HVLS-2 208 V 3 6 A WIRELESS CONTROLLER LB-38,40,42 #12'S 5 MECHANICAL - PTAC SCHEDULE EQUIP. ID VOLTS PH. WATTS FLA CIRCUIT FEEDER NOTES PTAC-1 208 V 1 3500 W 17 A LA-39,41 #10'S PTAC-2 208 V 1 3500 W 17 A LA-43,45 #10'S No. Description Date 1 HVAC Changes 7/26/22 1 UTILITY XFMR BY ROCKY MOUNTAIN POWER (RMP). PAD AND VAULT PROVIDED AND INSTALLED BY E.C. PER RMP STANDARDS UNDERGROUND SECONDARY; (4) 4" CONDUIT, TRENCHING AND BACKFILL BY ELEC. CONTRACTOR, CONDUCTORS BY UTILITY CO. FAULT CURRENT CALULATIONS WERE BASED ON INFINITE BUS, WITH AN ESTIMATED 300KVA TRANSFORMER WITH A 3.21%Z. PANEL 'LA' MAIN FLOOR UNDERGROUND PRIMARY; (2) 4"CONDUIT, TRENCHING AND BACKFILL BY ELEC. CONTRACTOR, CONDUCTORS BY UTILITY CO. PANEL 'LB' PANEL 'LC' 800A 208Y/120V,3P,4W NEMA 3R CT CAN PANEL 'MDP' GND BAR (3) 3"C., EA. W/4#300 METER BASE & CT CAN PER RMP CO. REQUIREMENTS GROUNDING ELECTRODE SYSTEM M (2) 2" C. FOR FUTURE WASHBAY AND MONUMENT SIGN *25,972A *19,817A *13,443A *6,324A BLDG. STEEL WATER MAIN GROUND BAR AT MAIN TTB GRND RODS STAND-OFF GROUND BAR LOCATED IN ELEC. RM NEXT TO SERVICE EQUIP. GROUND BAR SHALL BE ERICO #EGBA14412CC OR EQUAL. PROVIDE AND INSTALL ALL REQ'D LUGS & TERMINALS. MOUNT VERT. TO CONSERVE AS MUCH WALL SPACE AS POSSIBLE. MAIN SERVICE EQUIPMENT G N NEUTRAL TO GND BOND AT THIS POINT ONLY #3/0 Cu #6 C u CONCRETE ENCASED ELECTRODE 3/ 4 " C . , 1 # 6 C u #3 / 0 C u #3 / 0 C u #4 C u BOND TO FIRE SPRINKLER RISER #3 / 0 C u 13053 STATEOFIDAHOSHAWNA.M E A D ORREGISTEREDRP OFESSIONALENGIN EE R 1823 E. Center Pocatello, Idaho 83201 tel (208) 232-4439 www.payneengineeringinc.com Engineering Inc. Consulting Engineers BO O T H Date Sheet No. A r c h i t e c t u r e (2 0 8 ) 2 3 3 - 4 5 4 8 Ph o n e Po c a t e l l o , I d a h o 8 3 2 0 1 34 0 E a s t C l a r k S t r e e t , S u i t e A (2 0 8 ) 2 3 3 - 0 2 6 3 te d @ b o o t h a r c h i t e c t u r e . c o m Fa x em a i l P L L C Ne w B u i l d i n g f o r : P.E. #:2265 7/20/22 Re v i s i o n s POWER RISER, SCHEDULES & DETAILS Mo u n t a i n W e s t 07-20-2022 TB D Re x b u r g , I d a h o E3.0 SCALE: 12" = 1'-0"1 POWER RISER DIAGRAM A. THESE PLANS HAVE BEEN PREPARED WITHOUT UTILITY COMPANY COMMENTS. THE E.C. SHALL VERIFY THE EXACT REQUIREMENTS FOR THE ELECTRIC AND TELEPHONE SERVICES WITH THE UTILITY COMPANY REPRESENTATIVES AND PROVIDE ALL WORK AND PAY ALL COSTS FOR A COMPLETE AND OPERATING SYSTEM, AS DIRECTED BY THE GOVERNING UTILITIES. GENERAL NOTES: POWER RISER FEEDER SCHEDULE SOURCE LOAD # OF CONDUIT RUNS CONDUIT SIZE FEEDER SIZE CONDUCTOR TYPE LOAD AMPS FEEDER BREAKER SIZE MDP PANEL LA 1 2" 3-#3/0, 1-#3/0, 1-#6 COPPER 152 A 200 A MDP PANEL LB 1 2" 3-#3/0, 1-#3/0, 1-#6 COPPER 66 A 200 A MDP PANEL LC 1 2" 3-#3/0, 1-#3/0, 1-#6 COPPER 100 A 200 A FEEDER SCHEDULE LEGEND & NOTES QTY & SIZE OF PHASE CONDUCTOR(S) QTY-#PHASE SIZE, QTY-#NEUTRAL SIZE, QTY-#GROUND SIZE QTY & SIZE OF NEUTRAL CONDUCTOR(S) QTY & SIZE OF GROUND CONDUCTOR(S) 1. # OF RUNS INDICATES THE NUMBER OF PARALLEL RUNS FOR THE FEEDER. 2. FEEDER SIZE IN SCHEDULE IS AS INDICATED BELOW: S = SHUNT-TRIP BREAKER G = GFCI BREAKER R = RED HANDLED, LOCK-OUT TYPE A = ARC-FAULT BREAKER GP = GFEPD BREAKER LCP = CRKT TO BE ROUTED THROUGH LTG CONTROL PANEL BRK NOTES: Elec. Heating 12400 VA 100.00% 12400 VA Welder 16000 VA 87.50% 14000 VA Receptacle 18060 VA 77.69% 14030 VA TOTAL EST. DEMAND AMPS:310 A Other 1000 VA 100.00% 1000 VA TOTAL CONN. AMPS.:317 A Motor 42686 VA 108.23% 46200 VA TOTAL EST. DEMAND:111855 VA Lighting 9959 VA 100.00% 9959 VA TOTAL CONN. LOAD:114366 VA HVAC 15425 VA 100.00% 15425 VA LOAD CLASSIFICATION CONNECTED LOAD DEMAND FACTOR EST. DEMAND PANEL TOTALS PANEL LOAD SUMMARY TOTAL AMPS:311 A 315 A 328 A TOTAL LOAD:37.3 kVA 37.7 kVA 39.4 kVA 23 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 24 21 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 22 19 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 20 17 0 -- 1 -- -- PREPARED SPACE 18 15 0 -- 1 -- -- PREPARED SPACE 16 13 SPARE -- 100 A 3 0 -- 1 -- -- PREPARED SPACE 14 11 14467 0 12 9 10107 0 10 7 PANEL LC 200 A 3 11367 0 3 200 A -- SPARE 8 5 17014 7973 6 3 19873 7860 4 1 PANEL LA 200 A 3 18024 7960 3 200 A PANEL LB 2 CKT CIRCUIT DESCRIPTION NOTE AMPS P A B C P AMPS NOTE CIRCUIT DESCRIPTION CKT SERVICE ENTRANCE RATED NOTES: MFG/ MODEL:SQ. D/I-LINE DIMENSIONS:44"W x 11.5"D x *"H FEED:BOTTOM ENCLOSURE:NEMA 1 BUSSING:SEE SPEC'S MBR AMPS:800 A MOUNTING:SURFACE WIRES:4 PANEL AMPS:800 A FED FROM:PHASES:3 PANEL TYPE:MBR Mountain West LOCATION: VOLTAGE:120/208 Wye A.I.C. RATING:42k PROJECT: PANEL: MDP PAYNE ENGINEERING S = SHUNT-TRIP BREAKER G = GFCI BREAKER R = RED HANDLED, LOCK-OUT TYPE A = ARC-FAULT BREAKER GP = GFEPD BREAKER LCP = CRKT TO BE ROUTED THROUGH LTG CONTROL PANEL BRK NOTES: TOTAL ESTIMATED DEMAND AMPS:149 A TOTAL AMPS:151 A 167 A 142 A TOTAL LOAD:18.0 kVA 19.9 kVA 17.0 kVA 53 2250 2138 54 51 Water Heater 30 A 2 2250 2138 2 40 A HVAC CU-3 52 49 SPARE -- 20 A 1 0 2912 50 47 SPARE -- 20 A 1 0 2912 2 60 A HVAC CU-2 48 45 1750 2662 46 43 PTAC 20 A 2 1750 2662 2 50 A HVAC CU-1 44 41 1750 653 1 15 A Furnace 42 39 PTAC 20 A 2 1750 1046 1 15 A Furnace 40 37 SPARE -- 20 A 1 0 806 1 15 A Furnace 38 35 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 36 33 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 34 31 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 32 29 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 30 27 Overhead Door 20 A 1 653 540 1 20 A Receptacle 28 25 Elec. Heating/Recpt. 20 A 1 617 622 1 20 A Receptacle 26 23 Elec. Heating/Recpt. 20 A 1 617 1080 1 20 A Receptacle 24 21 Receptacle 20 A 1 1080 720 1 20 A Receptacle 22 19 Receptacle 20 A 1 1293 900 1 20 A Receptacle 20 17 Receptacle 20 A 1 360 900 1 20 A Receptacle 18 15 Lighting 20 A 1 1065 1140 1 20 A Receptacle 16 13 Lighting 20 A 1 1316 1000 1 20 A Automatic Doors 14 11 Lighting - Exterior LCP 20 A 1 1030 1080 1 20 A Receptacle 12 9 Lighting LCP 20 A 1 740 900 1 20 A Receptacle 10 7 Lighting LCP 20 A 1 1425 1080 1 20 A Receptacle 8 5 Lighting - Shop LCP 20 A 1 1500 1080 1 20 A Receptacle 6 3 Lighting - Shop LCP 20 A 1 1500 360 1 20 A Receptacle 4 1 Lighting - Shop LCP 20 A 1 1500 360 1 20 A Receptacle 2 CKT CIRCUIT DESCRIPTION NOTE AMPS P A B C P AMPS NOTE CIRCUIT DESCRIPTION CKT NOTES: MFG & MODEL:SQ. D/NQ SERIES DIMENSIONS:20"W x 5.8"D x *"H FEED:BOTTOM ENCLOSURE:NEMA 1 BUSSING:SEE SPEC'S MBR AMPS:N/A MOUNTING:SURFACE WIRES:4 PANEL AMPS:225 A FED FROM:MDP PHASES:3 PANEL TYPE:MLO Mountain West LOCATION: VOLTAGE:120/208 Wye A.I.C. RATING:22k PROJECT: PANEL: LA PAYNE ENGINEERING S = SHUNT-TRIP BREAKER G = GFCI BREAKER R = RED HANDLED, LOCK-OUT TYPE A = ARC-FAULT BREAKER GP = GFEPD BREAKER LCP = CRKT TO BE ROUTED THROUGH LTG CONTROL PANEL BRK NOTES: TOTAL ESTIMATED DEMAND AMPS:76 A TOTAL AMPS:66 A 65 A 67 A TOTAL LOAD:8.0 kVA 7.9 kVA 8.0 kVA 41 4667 730 42 39 4667 730 40 37 Bridge Crane 60 A 3 4667 730 3 20 A Shop Fan 38 35 PREPARED SPACE -- -- 1 -- 730 36 33 PREPARED SPACE -- -- 1 -- 730 34 31 PREPARED SPACE -- -- 1 -- 730 3 20 A Shop Fan 32 29 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 30 27 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 28 25 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 26 23 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 24 21 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 22 19 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 20 17 SPARE -- 20 A 1 0 653 1 20 A Overhead Door 18 15 SPARE -- 20 A 1 0 653 1 20 A Overhead Door 16 13 SPARE -- 20 A 1 0 653 1 20 A Overhead Door 14 11 SPARE -- 20 A 1 0 653 1 20 A Overhead Door 12 9 SPARE -- 20 A 1 0 540 1 20 A Receptacle 10 7 SPARE -- 20 A 1 0 590 1 20 A Receptacle 8 5 SPARE -- 20 A 1 0 540 1 20 A Receptacle 6 3 SPARE -- 20 A 1 0 540 1 20 A Receptacle 4 1 SPARE -- 20 A 1 0 590 1 20 A Receptacle 2 CKT CIRCUIT DESCRIPTION NOTE AMPS P A B C P AMPS NOTE CIRCUIT DESCRIPTION CKT NOTES: MFG & MODEL:SQ. D/NQ SERIES DIMENSIONS:20"W x 5.8"D x *"H FEED:BOTTOM ENCLOSURE:NEMA 1 BUSSING:SEE SPEC'S MBR AMPS:N/A MOUNTING:SURFACE WIRES:4 PANEL AMPS:225 A FED FROM:MDP PHASES:3 PANEL TYPE:MLO Mountain West LOCATION: VOLTAGE:120/208 Wye A.I.C. RATING:22k PROJECT: PANEL: LB PAYNE ENGINEERING S = SHUNT-TRIP BREAKER G = GFCI BREAKER R = RED HANDLED, LOCK-OUT TYPE A = ARC-FAULT BREAKER GP = GFEPD BREAKER LCP = CRKT TO BE ROUTED THROUGH LTG CONTROL PANEL BRK NOTES: TOTAL ESTIMATED DEMAND AMPS:102 A TOTAL AMPS:96 A 84 A 122 A TOTAL LOAD:11.4 kVA 10.1 kVA 14.5 kVA 41 3833 4000 42 39 3833 4000 2 50 A G Welder 40 37 Air Compressor 60 A 3 3833 4000 38 35 1441 4000 2 50 A G Welder 36 33 1441 -- 1 -- -- PREPARED SPACE 34 31 Air Handler 20 A 3 1441 -- 1 -- -- PREPARED SPACE 32 29 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 30 27 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 28 25 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 26 23 PREPARED SPACE -- -- 1 -- -- 1 -- -- PREPARED SPACE 24 21 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 22 19 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 20 17 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 18 15 SPARE -- 20 A 1 0 0 1 20 A -- SPARE 16 13 SPARE -- 20 A 1 0 653 1 20 A Overhead Door 14 11 SPARE -- 20 A 1 0 653 1 20 A Overhead Door 12 9 SPARE -- 20 A 1 0 653 1 20 A Overhead Door 10 7 SPARE -- 20 A 1 0 720 1 20 A Receptacle 8 5 SPARE -- 20 A 1 0 540 1 20 A Receptacle 6 3 SPARE -- 20 A 1 0 180 1 20 A Receptacle 4 1 SPARE -- 20 A 1 0 720 1 20 A Receptacle 2 CKT CIRCUIT DESCRIPTION NOTE AMPS P A B C P AMPS NOTE CIRCUIT DESCRIPTION CKT NOTES: MFG & MODEL:SQ. D/NQ SERIES DIMENSIONS:20"W x 5.8"D x *"H FEED:BOTTOM ENCLOSURE:NEMA 1 BUSSING:SEE SPEC'S MBR AMPS:N/A MOUNTING:SURFACE WIRES:4 PANEL AMPS:225 A FED FROM:MDP PHASES:3 PANEL TYPE:MLO Mountain West LOCATION: VOLTAGE:120/208 Wye A.I.C. RATING:10k PROJECT: PANEL: LC PAYNE ENGINEERING SCALE: NONEABLDG GROUNDING ELECTRODE SYSTEM DETAIL No. Description Date 1 HVAC Changes 7/26/22 1