HomeMy WebLinkAboutAPPROVED PLANS - 22-00332 - Rexburg FM Office - RemodelAuthor Name Author Email Author Phone No.:
Alex Owens Alex.Owens@rexburg.org 208-372-2330
Cody Jones Cody.Jones@rexburg.org 208-372-2173
Don Allen Don.Allen@rexburg.org 208-372-2174
Description : Rexburg FM Office - Remodel
Address : 434 E 2nd N
Record Type : Commercial - Remodel
Document Filename : 21013 - Rexburg FM Toilet Remodel - Bid Set.pdf
Comment Author Contact Information:
Corrections in the following table need to be applied before a permit can be issued
Review Report
Approved
# 22-00332
Page Reference Annotation
Type
Author : Department Status Page Review Comments Applicant Response Comments
TS1.1 Stamp Cody Jones : Building Open 1 Approved - Building Inspector
TS1.1 Free text Cody Jones : Building Open 1 All construction and materials will need to be in compliance
with 2018 IBC.
TS1.1 Stamp Alex Owens : Electrical Open 1 Approved - Electrical Inspector
TS1.1 Free text Alex Owens : Electrical Open 1 All electrical work must meet 2017 NEC requirements
TS1.1 Stamp Don Allen : Mechanical Open 1 Approved - Plumbing Inspector
TS1.1 Stamp Don Allen : Mechanical Open 1 Approved - Mechanical Inspector
TS1.1 Stamp Don Allen : Mechanical Open 1 Approved - Mechanical Inspector
Commercial - Remodel
Approval of plans does not constitute approval of variance from code
Powered by TCPDF (www.tcpdf.org)
TITLE SHEET, INDEX & KEY PLAN
T
S
1
.
1
N
N
990 JOHN ADAMS PARKWAY P.O. BOX 2212 - IDAHO FALLS, IDAHO 83402-2212
(P) 208-522-8779 (F) 208-522-8785 (W) nbwarchitects.com
ARCHITECTURE PLANNING INTERIORS
architects p.a.nbwD
R
A
W
I
N
G
N
O
.
:
R
E
V
I
S
I
O
N
S
PROJECT:
SHEET TITLE:
P
R
O
J
E
C
T
N
O
.
D
A
T
E
:
D
R
A
W
N
B
Y
:
C
H
E
C
K
E
D
B
Y
:
REXBURG FM OFFICE/JR. SEMINARY
REXBURG IDAHO NORTH STAKE
PROPERTY NO. 511-3067
TOILET ROOM ADDITION FOR:
G
L
N
2
1
0
1
3
M
A
Y
2
0
2
2
C
J
R
05-16-2022
All construction and materials will need to be in compliance with 2018 IBC. All electrical work must meet 2017 NEC requirements
990 JOHN ADAMS PARKWAY P.O. BOX 2212 - IDAHO FALLS, IDAHO 83402-2212
(P) 208-522-8779 (F) 208-522-8785 (W) nbwarchitects.com
ARCHITECTURE PLANNING INTERIORS
architects p.a.nbwD
R
A
W
I
N
G
N
O
.
:
R
E
V
I
S
I
O
N
S
PROJECT:
SHEET TITLE:
P
R
O
J
E
C
T
N
O
.
D
A
T
E
:
D
R
A
W
N
B
Y
:
C
H
E
C
K
E
D
B
Y
:
REXBURG FM OFFICE/JR. SEMINARY
REXBURG IDAHO NORTH STAKE
PROPERTY NO. 511-3067
TOILET ROOM ADDITION FOR:
G
L
N
2
1
0
1
3
M
A
Y
2
0
2
2
C
J
R
05-16-2022
A
1
.
1
DEMOLITION AND CONSTRUCTION FLOOR AND CEILING PLANS
N
N
N
N
S
C
A
L
E
:
A
2
.
1
INTERIOR ELEVATIONS, SCHEDULES AND DETAILS
990 JOHN ADAMS PARKWAY P.O. BOX 2212 - IDAHO FALLS, IDAHO 83402-2212
(P) 208-522-8779 (F) 208-522-8785 (W) nbwarchitects.com
ARCHITECTURE PLANNING INTERIORS
architects p.a.nbwD
R
A
W
I
N
G
N
O
.
:
R
E
V
I
S
I
O
N
S
PROJECT:
SHEET TITLE:
P
R
O
J
E
C
T
N
O
.
D
A
T
E
:
D
R
A
W
N
B
Y
:
C
H
E
C
K
E
D
B
Y
:
REXBURG FM OFFICE/JR. SEMINARY
REXBURG IDAHO NORTH STAKE
PROPERTY NO. 511-3067
TOILET ROOM ADDITION FOR:
G
L
N
2
1
0
1
3
M
A
Y
2
0
2
2
C
J
R
05-16-2022
1
0
1
990 JOHN ADAMS PARKWAY P.O. BOX 2212 - IDAHO FALLS, IDAHO 83402-2212
(P) 208-522-8779 (F) 208-522-8785 (W) nbwarchitects.com
ARCHITECTURE PLANNING INTERIORS
architects p.a.nbwD
R
A
W
I
N
G
N
O
.
:
R
E
V
I
S
I
O
N
S
PROJECT:
SHEET TITLE:
P
R
O
J
E
C
T
N
O
.
D
A
T
E
:
D
R
A
W
N
B
Y
:
C
H
E
C
K
E
D
B
Y
:
REXBURG FM OFFICE/JR. SEMINARY
REXBURG IDAHO NORTH STAKE
PROPERTY NO. 511-3067
TOILET ROOM ADDITION FOR:
G
L
N
2
1
0
1
3
M
A
Y
2
0
2
2
C
J
R
01 0
F
1
.
1
SIGNAGE & FURNISHING PLANS AND SCHEDULES
N
N
S
C
A
L
E
:
1
/
2
"
=
1
'
-
0
"
P
R
O
J
E
C
T
N
O
,
D
A
T
E
:
D
R
A
W
N
B
Y
:
PROJECT:R
E
V
I
S
I
O
N
S
SHEET TITLE:
C
H
E
C
K
E
D
B
Y
:
D
R
A
W
I
N
G
N
O
.
:
2
2
0
2
6
M
A
Y
2
0
2
2
D
H
A
N
S
E
N
J
S
A
I
L
S
B
E
R
Y
E
n
g
i
n
e
e
r
e
d
S
y
s
t
e
m
s
A
s
s
o
c
i
a
t
e
s
REXBURG FM OFFICE / JR. SEMINARY
REXBURG IDAHO NORTH STAKE
TOILET ROOM ADDITION FOR:
PROPERTY NO. 511-3067
FLOOR PL
A
N
-
D
E
M
O
L
I
T
I
O
N
N
o
r
t
h
SCALE: 1/8" = 1'-0"
E
N
L
A
R
G
E
D
F
L
O
O
R
P
L
A
N
-
M
E
C
H
/
P
L
U
M
B
N
o
r
t
h
S
C
A
L
E
:
1
/
4
"
=
1
'
-
0
"
E
X
I
S
T
I
N
G
4
"
S
S
EXI
S
T
I
N
G
4" S
S
TO EXISTINGMAN HOLE INSTREET
P
L
A
N
N
O
T
E
S
:
1
E
X
I
S
T
I
N
G
F
I
X
T
U
R
E
T
O
R
E
M
A
I
N
.
P
R
O
T
E
C
T
I
N
P
L
A
C
E
D
U
R
I
N
G
C
O
N
S
T
R
U
C
T
I
O
N
.
E
X
I
S
T
I
N
G
F
I
X
T
U
R
E
T
O
B
E
R
E
M
O
V
E
D
A
N
D
D
I
S
P
O
S
E
D
O
F
.
D
E
M
O
H
O
T
A
N
D
C
O
L
D
P
I
P
I
N
G
F
R
O
M
E
X
I
S
T
I
N
G
S
I
N
K
T
O
W
A
T
E
R
M
A
I
N
S
A
B
O
V
E
W
A
T
E
R
H
E
A
T
E
R
.
D
E
M
O
E
X
I
S
T
I
N
G
1
-
1
/
2
"
S
A
N
I
T
A
R
Y
L
I
N
E
F
R
O
M
S
I
N
K
C
A
P
A
T
T
E
E
.
E
X
I
S
T
I
N
G
1
-
1
/
4
"
V
E
N
T
A
N
D
2
"
S
A
N
I
T
A
R
Y
T
O
R
E
M
A
I
N
.
C
O
N
N
E
C
T
H
O
T
A
N
D
C
O
L
D
W
A
T
E
R
A
T
E
X
I
S
T
I
N
G
3
/
4
"
M
A
I
N
S
A
B
O
V
E
W
A
T
E
R
H
E
A
T
E
R
.
C
O
N
F
I
R
M
E
X
I
S
T
I
N
G
C
O
N
D
I
T
I
O
N
S
.
P
R
O
V
I
D
E
B
A
L
L
V
A
L
V
E
S
A
N
D
I
N
S
T
A
L
L
W
A
T
E
R
L
I
N
E
S
H
I
G
H
I
N
C
E
I
L
I
N
G
S
P
A
C
E
A
N
D
S
H
A
L
L
N
O
T
T
O
I
M
P
E
D
E
T
H
E
A
C
C
E
S
S
.
C
O
N
N
E
C
T
1
/
2
"
C
W
T
O
T
R
A
P
P
R
I
M
E
R
.
E
X
I
S
T
I
N
G
S
A
N
I
T
A
R
Y
L
I
N
E
T
O
R
E
M
A
I
N
.
B
O
R
E
4
"
S
A
N
I
T
A
R
Y
U
N
D
E
R
S
T
O
R
A
G
E
A
N
D
M
E
C
H
A
N
I
C
A
L
R
O
O
M
F
L
O
O
R
S
A
T
A
P
P
R
O
X
I
M
A
T
E
L
Y
4
8
"
B
E
L
O
W
G
R
A
D
E
.
C
O
N
F
I
R
M
E
X
I
S
T
I
N
G
C
O
N
D
I
T
I
O
N
S
A
N
D
P
A
T
H
O
B
S
T
R
U
C
T
I
O
N
S
P
R
I
O
R
T
O
W
O
R
K
.
C
O
N
N
E
C
T
T
O
E
X
I
S
T
I
N
G
4
"
S
A
N
I
T
A
R
Y
L
I
N
E
.
V
E
R
I
F
Y
E
X
I
S
T
I
N
G
C
O
N
D
I
T
I
O
N
S
P
R
I
O
R
T
O
D
E
M
O
L
I
T
I
O
N
.
C
O
N
N
E
C
T
T
O
E
X
I
S
T
I
N
G
4
"
V
E
N
T
A
B
O
V
E
2
N
D
R
O
O
F
.
V
E
R
I
F
Y
E
X
I
S
T
I
N
G
C
O
N
D
I
T
I
O
N
S
P
R
I
O
R
T
O
W
O
R
K
.
S
E
A
L
R
O
O
F
P
E
N
E
T
R
A
T
I
O
N
S
.
E
X
T
E
N
D
6
"
E
X
H
A
U
S
T
V
E
N
T
T
O
R
O
O
F
W
I
T
H
R
O
O
F
C
A
P
.
C
U
T
,
F
L
A
S
H
,
A
N
D
R
E
P
A
I
R
R
O
O
F
T
O
B
E
W
A
T
E
R
T
I
G
H
T
.
N
O
W
O
R
K
T
O
B
E
D
O
N
E
I
N
T
H
I
S
S
P
A
C
E
.
P
R
O
T
E
C
T
D
U
R
I
N
G
C
O
N
S
T
R
U
C
T
I
O
N
.
R
E
M
O
V
E
A
N
D
R
E
I
N
S
T
A
L
L
P
L
U
M
B
I
N
G
F
I
X
T
U
R
E
A
S
R
E
Q
U
I
R
E
D
T
O
C
O
M
P
L
E
T
E
F
U
L
L
S
C
O
P
E
O
F
W
O
R
K
.
2
3
4
2
1
3
1
3
4
1
1
1
3
1
3
1
3
1
5
121212121212 1212
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1212
1
2
1
2
1
2
1
2
1
2
1212
1
2
6
3
E
X
I
S
T
I
N
G
4
"
V
E
X
I
S
T
I
N
G
4
"
V
3
/
4
"
C
W
1
/
2
"
H
W
2
"
V
2
"
V
4
"
4
"
4
"
1
E
H
1
E
F
1
E
F
1
E
H
F
D
-
1
F
D
-
1
W
C
-
1
W
C
-
1
T
P
-
1
L
-
1
3
/
4
"
C
W
L
-
1
W
C
O
9
4
1
0
8
7
8
9
1
0
1
1
1
2
1
3
5
5
6
7
7
8
1
1
1
1
1
E
X
I
S
T
I
N
G
W
A
T
E
R
H
E
A
T
E
R
MECHANICAL AND PLUMBING DEMOLITION AND FLOOR PLANS
M
1
.
1
R
E
F
E
R
T
O
E
N
L
A
R
G
E
D
F
L
O
O
R
P
L
A
N
OFFICEMEN
V
E
S
T
I
B
U
L
E
M
E
C
H
.
R
O
O
M
W
O
M
E
N
ROOM
O
F
F
I
C
E
O
F
F
I
C
E
F
M
O
F
F
I
C
E
F
M
O
F
F
I
C
E
O
F
F
I
C
E
O
F
F
I
C
E
S
T
O
R
.
S
T
O
R
.
STOR.MECH.OFFICEOFFICEMECH.JAN.ROOMROOMROOM
R
O
O
M
VESTIBULE
F
O
Y
E
R
O
F
F
I
C
E
O
F
F
I
C
E
F
M
S
T
O
R
A
G
E
O
F
F
I
C
E
CORRIDORCORRIDORCORRIDOR
C
O
R
R
I
D
O
R
C
O
R
R
I
D
O
R
F
M
O
F
F
I
C
E
F
M
S
T
O
R
A
G
E
C
O
R
R
I
D
O
R
F
M
S
T
O
R
A
G
E
O
F
F
I
C
E
F
M
S
T
O
R
A
G
E
F
M
O
F
F
I
C
E
F
M
O
F
F
I
C
E
O
F
F
I
C
E
R
O
O
M
S
T
O
R
.
S
T
O
R
.
M
E
C
H
.
R
O
O
M
W
O
M
E
N
C
O
R
R
I
D
O
R
W
O
M
E
N
M
E
N
1
3
P
R
O
J
E
C
T
N
O
,
D
A
T
E
:
D
R
A
W
N
B
Y
:
PROJECT:R
E
V
I
S
I
O
N
S
SHEET TITLE:
C
H
E
C
K
E
D
B
Y
:
D
R
A
W
I
N
G
N
O
.
:
2
2
0
2
6
M
A
Y
2
0
2
2
D
H
A
N
S
E
N
J
S
A
I
L
S
B
E
R
Y
E
n
g
i
n
e
e
r
e
d
S
y
s
t
e
m
s
A
s
s
o
c
i
a
t
e
s
REXBURG FM OFFICE / JR. SEMINARY
REXBURG IDAHO NORTH STAKE
TOILET ROOM ADDITION FOR:
PROPERTY NO. 511-3067
NO SCALE CEILING MOUNTED EXHAUST FAN DETAIL DAMPER BACK-DRAFT CEILING GRILLECEILING EXHAUST FAN FAN ASSEMBLYCABINETINSULATED ROOF SHINGLES FLASH INTO SHINGLES ANDSEAL WATERTIGHT12x12 ROOF CAP WITHBACK-DRAFT DAMPER(SLOPED ROOF TYPE)10x10 EXHAUST PLENUM6"Ø EA6"Ø EA FAN ASSEMBLYCABINETINSULATED EXHAUST FAN DAMPER BACK-DRAFT NO SCALE TRAP PRIMER DETAIL CONCRETE FILLWATERPROOF MEMBRANEWHERE REQUIREDHORIZONTALRUN IN PIPE 12" MIN. TOSLAB STRUCTURAL BREAKING PORTS AIR GAP VACUUM FIXTURE NEAREST FLOW TOFLOOR DRAINOUTLET TO P-TRAP CEMENT BED FLOORING IF APPLICABLE1/2" PEX TRAP PRIMERBALL TYPE SHUT-OFF VALVE MOUNT IN RECESSED BOX IN WALL. PROVIDE8X8 BOX WITH WITH DOOR.WALL CLEANOUT DETAILNO SCALE 1'-0"1/8 BEND IF CLEANOUTOCCURS AT END OF LINE.WASTE LINE WASTE LINE.LENGTH TO SUIT.1/8 BEND CHROMEWALL COVERAND SCREWFLOOR LINE WALL MAY EXTEND AS AWASTE OR VENTPLUGGED TEEWITH CLEANOUT
1
E
F
S
Y
M
.
E
X
H
A
U
S
T
F
A
N
S
C
H
E
D
U
L
E
V
E
N
T
W
A
S
T
E
H
O
T
C
O
L
D
S
Y
M
.
F
I
X
T
U
R
E
S
C
H
E
D
U
L
E
D
E
S
C
R
I
P
T
I
O
N
F
D
-
1
2
"
F
L
O
O
R
D
R
A
I
N
-
Z
U
R
N
Z
-
4
1
5
W
I
T
H
5
Ø
N
I
C
K
E
L
-
B
R
O
N
Z
E
S
T
R
A
I
N
E
R
,
2
"
D
E
E
P
S
E
A
L
P
-
T
R
A
P
A
N
D
T
R
A
P
P
R
I
M
E
R
.
-
-
-
2
"
1
/
2
"
-
-
-
L
-
1
1
-
1
/
2
"
1
-
1
/
2
"
1
/
2
"
1
/
2
"
-
-
-
-
1
/
2
"
-
-
T
P
-
1
2
"
4
"
1
/
2
"
-
-
-
W
C
-
1
A
D
A
W
A
L
L
H
U
N
G
L
A
V
A
T
O
R
Y
-
K
O
H
L
E
R
K
-
2
0
3
1
-
0
"
G
R
E
E
N
W
I
C
H
"
W
I
T
H
W
A
L
L
C
A
R
R
I
E
R
,
M
O
E
N
8
4
3
0
F
A
U
C
E
T
&
W
A
T
T
S
S
E
R
I
E
S
L
F
U
S
G
-
B
M
I
X
I
N
G
V
A
L
V
E
,
K
-
7
7
1
5
O
P
E
N
G
R
I
D
S
T
R
A
I
N
E
R
W
I
T
H
O
F
F
S
E
T
W
A
S
T
E
L
I
N
E
,
1
/
2
"
S
T
O
P
S
A
N
D
1
-
1
/
4
"
P
-
T
R
A
P
.
P
R
O
V
I
D
E
I
N
S
U
L
A
T
I
N
G
J
A
C
K
E
T
O
N
H
W
A
N
D
W
A
S
T
E
P
I
P
I
N
G
.
R
E
M
A
R
K
S
R
.
P
.
M
.
W
A
T
T
S
C
H
A
R
.
C
O
N
T
R
O
L
C
.
F
.
M
.
T
Y
P
E
S
.
P
.
E
.
S
Y
M
.
C
E
I
L
I
N
G
M
O
U
N
T
E
D
1
0
0
T
W
I
N
C
I
T
Y
T
1
5
0
W
I
T
H
B
A
C
K
D
R
A
F
T
D
A
M
P
E
R
A
N
D
6
"
Ø
D
U
C
T
U
P
T
H
R
U
W
A
L
L
A
B
O
V
E
T
O
R
O
O
F
C
A
P
0
.
3
7
5
"
1
0
0
1
2
0
/
6
0
/
1
7
0
0
A
D
A
T
A
N
K
T
Y
P
E
W
A
T
E
R
C
L
O
S
E
T
-
O
W
N
E
R
P
R
O
V
I
D
E
D
,
C
O
N
T
R
A
C
T
O
R
I
N
S
T
A
L
L
E
D
.
W
A
T
E
R
C
L
O
S
E
T
W
/
E
L
O
N
G
A
T
E
D
B
O
W
L
,
W
H
I
T
E
O
P
E
N
F
R
O
N
T
S
E
A
T
,
A
N
D
B
O
L
T
C
A
P
S
.
T
R
A
P
P
R
I
M
E
R
-
Z
U
R
N
Z
1
0
2
0
X
L
T
R
A
P
P
R
I
M
E
R
.
M
O
U
N
T
R
E
C
E
S
S
E
D
I
N
W
A
L
L
B
E
L
O
W
S
I
N
K
A
N
D
P
R
O
V
I
D
E
L
O
C
K
E
D
C
O
V
E
R
.
R
U
N
1
/
2
"
C
O
L
D
W
A
T
E
R
L
I
N
E
T
O
E
A
C
H
T
R
A
P
.
R
E
F
E
R
T
O
D
E
T
A
I
L
O
N
M
P
1
.
2
F
O
R
T
Y
P
I
C
A
L
I
N
S
T
A
L
L
A
T
I
O
N
.
W
I
T
H
L
I
G
H
T
S
E
L
E
C
T
R
I
C
H
E
A
T
E
R
S
C
H
E
D
U
L
E
E
H
1
S
Y
M
.
T
Y
P
E
K
W
C
H
A
R
C
O
N
T
R
O
L
R
E
M
A
R
K
S
W
A
L
L
M
O
U
N
T
E
D
0
.
3
7
5
1
2
0
/
6
0
/
1
I
N
T
E
G
R
A
L
Q
M
A
R
K
G
F
R
1
5
0
0
T
2
F
T
-
S
T
A
T
MECHANICAL AND PLUMBING SCHEDULES
M
1
.
2
S CD2
SCD2
F
F
CORRIDOR
CORRIDOR
WOMEN
MECH.
ROOM
STOR.
STOR.
MEN
WOMEN
3
3
3
3
3
3
3
'A'42"
42"
5
5
6
F1
F1
EF-1
120 V/1P100 W
EF-1
120 V/1P100 W
EH-1
120 V/1P375 W
EH-1
120 V/1P375 W
A-25
CORRIDOR
CORRIDOR
WOMEN
MECH.
ROOM
STOR.
STOR.
WORK
ROOM
'A'1
'SOUND
SYSTEM'
2
3
3
3
3
3
3
3
4
ELECTRICAL SPECIFICATIONS
1. INTENT:
Provide and install complete and operable electrical systems
including but not not limited to; lighting, power, receptacles,
data, fire alarm ande etc.
Provide all required connections to all Mechanical and
Plumbing equipment, as indicated and required, including all
conduits, wiring and controls. Coordinate with mechanical
contractor and drawings.
2. COMPLIANCE WITH CODES:
All work and material shall comply with all applicable codes,
safety orders, laws, ordinances and regulations of governing
authorities and other agencies having jurisdiction including
regulations of the State and Local Fire Marshall, unless
detailed as specified to a more restrictive standard or higher
requirement.
3. INTERPRETATION OF DRAWINGS:
The electrical drawings are essentially diagrammatic in that
all provisions necessary to conform to structural,
architectural, mechanical and plumbing systems can not be
shown. All installations shall be adjusted as necessary to
conform and to avoid obstructions, without additional cost to
the owner.
All work, material and equipment called for by notes,
schedules or otherwise indicated on the drawings shall be
furnished and isntalled as though fully set forth in these
specifications.
4. VISITING THE SITE:
Contractor shall visit the site and become acquainted with
conditions to be encounterd. Extra funds will not be allowed
due to failuer to examine the site and to included existing
conditions in bid price.
5. COORDINATION WITH UTILITIES:
These plans have been prepared without utility company
comments. The contractor shall verify exact requirements for
the electrical, telephone and communication services with the
utility company representatives and provide all work and pay
all costs for a complete and operating systems, as directed by
the governing utilities.
6. MATERIALS AND WORKMANSHIP:
All workmanship shall be performed by skilled electricians
using the best standard practives of the trade. All materials
shall, unless otherwise noted, be new and in perfect
condition and working order. All material for similar uses shall
be of the same type, material and manufacturer for ease of
future maintaenance.
All equipment shall be readily accessible for maintenance and
repairs. All materials, fixtures and equipment shall be
covered or sealed upon installation so as to provide for safety
and to insure that operation and appearance will be
maintained after subsequent construction operations.
7. EXECUTION:
Raceway installation: Seperate underground conduits in a
common trench 4" minimum horizontally, 12" minimum from
other utility lines. Minimum conduit depth shall be 18".
Coordinate conduit installation with pipes, steel, footings and
ducts installed by other trades. Install conduit runs exposed to
view parallel or at right angles to structural members, walls or
building lines. Support conduit with one-hole malleable factory
made pipe straps, fastended with screws.
8. OPERATING AND ADJUSTING:
The owner reserves the right to operate any systems of
equipment prior to final comletion and acceptance of the work.
Such perliminary operation shall not be construed as an
acceptance of any work.
Each piece of equipment and all of the systems shall be
adjusted to insure proper functioning and shall be left in first
class operating condition.
9. CUTTING AND PATCHING:
Do all drilling and cutting as necessary for installation of
equipment or conduit. Cutting or drilling of structure is only
permitted with prior approval of the owner and structural
engineer.
Where cutting and patching of work is necessary, use the
same materials, workmanship and finish to neatly match all
surrounding work.
10. CONDUIT:
All conduit material and installation methods shall be as
allowed by the NEC, local AHJ and as directed by the
owner.
11. CONDUCTORS:
Type THWN or THHN copper wire insulated for 600V.
Smallest wire shall be #14 AWG unless noted otherwise.
All wiring shall be Copper unless indicated otherwise.
Type MC cable shall be permitted, provided it is installed in
concealed areas and installation complies with the Local AHJ
and NEC requirements.
Use "Ideal Yellow" pulling compound for all wire pulls.
Use Scotchlock connectors for all splices in #12 wire and
tape bolted pressure connectors for larger wire.
12. GROUNDING:
All conduit, branch circuits, feeders and etc. shall be
provided with a grounding conductor. All grounding
conductors shall be insulated and green in color, size as
shown.
13. WIRING DEVICES:
Devices shall be Standard type, Specification grade, color
as selected by owner. Decora style devices are prohibited.
Utilize GFCI and Tamper-proof devices in all locations as
defined by the NEC.
Wiring devices shall be as installed as allowed by the
NEC, local AHJ.
14. DEVICE PLATES:
Devices plate type and color shall be as directed by owner
and as required by the NEC.
15. LIGHTING FIXTURES:
As selected by owner and/or indicated in schedules. All light
fixtures shall be installed and connected by the Electrical
Contractor.
16. SERVICE EQUIPMENT & PANELBOARDS:
Service Equipment: Shall be rated as such and shall comply
with local utility co. requirments. .
Panelbards: Shall be provided with typed writtend directories
indicating loads being served.
Maintain all required clearances around equipment as
required by the NEC.
All equpment dimensions to be field verified.
17. CLEAN-UP:
Upon completion of the work, prior to final inspection,
thoroughly clean all exposed fixtures, trim and equipment
and leave the entire installation in a neat, clean and usable
condition. Remove all cement, paint, grease, oil and other
foreign substances.
18. TEST:
Test all conductors for shorts, opens, grounds or other
defects. Correct any defective work and re-test.
Demonstrate continuous satisfactory operation of all
electrical systems and equipment.
Provide training to the owner on electrical systems as
needed for owner operation and maintenance of building.
19. GUARANTEE:
Prior to final acceptacne of the project, deliver to the owner
a written one year guarantee on all workmanship, materials
and equipment and agree to repair or replace all such
defective items promptly that may occure during the
warranty period; including repair or replacement of the
premises that may be damaged due to faulty work and
materials furnished under contract.
CIRCUITING & GENERAL SYMBOL SCHEDULE
NOTE: ALL SYMBOLS MAY NOT BE USED
SYMBOL DESCRIPTION
KEYED NOTE REFERENCE1
BRANCH CIRCUIT HOME-RUN TO PANEL INDICATED
A-1,3,5
3/4"C.-6#12,1#12G
QTY & SIZE OF EQUIPMENT GROUND CONDUCTOR
QTY & SIZE OF NEUTRAL AND PHASE CONDUCTOR(S)
SIZE OF CONDUIT
A-1,3,5
3/4"C.-6#12,1#12G
PANEL AND CIRCUIT DESIGNATIONS
EQUIPMENT GROUNDING CONDUCTOR
TICK MARKS
NEUTRAL CONDUCTOR(S)
PHASE AND/OR SWITCH-LEG CONDUCTOR(S)
DETAIL # / SHEET REFERENCE1 / ES101
LIGHTING SYMBOL SCHEDULE
NOTE: ALL SYMBOLS MAY NOT BE USED
SYMBOL DESCRIPTION
PARKING AREA POLE LIGHT, SINGLE OR DOUBLE HEAD AS INDICATED ON
DRAWINGS. REFER TO LIGHT POLE DETAIL FOR POLE INFORMATION.
2X4 FLUORESCENT OR LED FIXTURE
2X2 FLUORESCENT OR LED FIXTURE
SURFACE MOUNTED FLUORESCENT OR LED FIXTURE
STRIP FLUORESCENT OR LED FIXTURE
WALL MOUNTED FLUORESCENT OR LED FIXTURE
EXTERIOR WALL MOUNTED FIXTURE
ROUND RECESSED FIXTURE
SURFACE OR PENDANT FIXTURE
LIGHT FIXTURE SUBSCRIPTS
NL NIGHT-LIGHT(CONNECT TO UNSWITCHED LEG OF CIRCUIT)
EXIT SIGN, WALL OR CEILING MOUNTING AS REQUIRED (SINGLE OR DOUBLE FACE)
DIRECTIONAL CHEVRONS AS INDICATED; CONNECT TO UNSWITCHED LEG OF LIGHTING
CIRCUIT THAT IS IN THE SAME AREA AS THE EXIT SIGNS.
SHADED FIXTURE INDICATES AN EMERGENCY FIXTURE. PROVIDE WITH EMERG. BATTERY
PACK OR CONNECT TO EMERGENCY POWER SYSTEM (WHERE APPLICABLE). CONNECT
BATTERY PACK TO UNSWITCHED LEG OF LIGHTING CIRCUIT THAT SERVES THE SAME
AREA AS THE EMERGENCY FIXTURE. PROVIDE WITH TEST LIGHT AND SWITCH.
CEILING MOUNTED OCCUPANCY SENSOR, REFER TO OCCUPANCY SENSOR/SWITCH
SCHEDULE FOR SENSOR TYPE AND ADDITIONAL INFORMATION.
SWITCH MOUNTED OCCUPANCY SENSOR, LOW VOLTAGE SWITCHPOD OR DIMMER
SWITCH, REFER TO OCCUPANCY SENSOR/SWITCH SCHEDULE FOR TYPE AND
ADDITIONAL INFORMATION.
SINGLE-POLE SWITCH (SEE SUB-SCRIPTS BELOW FOR ADDITIONAL INFORMATION)
SWITCH SUBSCRIPTS
3 3-WAY SWITCH
4 4-WAY SWITCH
D DIMMER SWITCH (COMPATIBLE W/ LOAD & LTG TYPES)
F 7-DAY PROGRAMMABLE TIMER SWITCH
(INTERMATIC MODEL EI500WC SERIES)
P PILOT LIGHTED SWITCH
F1 LIGHT FIXTURE TYPE DESIGNATION
S
###
WALL OR CEILING MOUNTED EMERGENCY LIGHTING UNIT W/BATTERY PACK
CONNECT TO UNSWITCHED LEG OF LIGHTING CIRCUIT THAT IS IN THE SAME AREA AS
THE EMERGENCY LIGHT.
LV LOW-VOLTAGE SWITCH (PER DWG'S)
T THERMAL-OVERLOAD SWITCH
M SWITCH SUPPLIED WITH EQUIPMENT,
INSTALLED BY E.C.
WP WEATHERPROOF
2P DOUBLE POLE, SINGLE THROW SWITCH
GENERAL LIGHTING NOTES:
A. SYMBOLS SHOWN ABOVE MAY NOT REPRESENT ALL LIGHT FIXTURES USED ON PROJECT, REFER TO
LIGHT FIXTURE SCHEDULE FOR ACTUAL FIXTURE INFORMATION INCLUDING FIXTURE TYPE, LAMPING,
MOUNTING AND ETC.
B. JUNCTION BOXES FOR LIGHTING CIRCUITING ARE NOT SHOWN FOR CLARITY. THE E.C. IS RESPONSIBLE
FOR PROVIDING AND INSTALLING ALL JUNCTION BOXES REQUIRED FOR CIRCUITING OF ALL LIGHT
FIXTURES THAT ARE NOT LISTED FOR "THROUGH-BRANCH CIRCUIT WIRING".
C. IN GENERAL ALL SWITCH-LEG CONDUCTORS MAY NOT BE SHOWN ON DRAWINGS; E.C. SHALL PROVIDE
AND INSTALL CONDUCTORS AS REQUIRED TO ACHIEVE CONTROL SCHEMES INDICATED AND
DESCRIBED ON DRAWINGS. INCLUDING ALL 0 - 10V DIMMING CONTROLS BETWEEN SWITCH AND
FIXTURES.
D. ALL BATTERY EXIT SIGNS AND EMERGENCY LIGHTING TO BE CONNECTED TO THE UNSWITCHED LEG OF
THE LIGHTING CIRCUIT IN THE AREA.
###
F
M
POWER SYMBOL SCHEDULE
NOTE: ALL SYMBOLS MAY NOT BE USED
SYMBOL DESCRIPTION
'LA'
ELECTRICAL PANELBOARD, (SEE POWER RISER AND PANEL SCHEDULES
FOR ADDITIONAL INFORMATION)
J
JUNCTION BOX
CR = CORD REEL; SEE DRAWINGS FOR INFORMATION
CD = CORD DROP; SEE DRAWINGS FOR INFORMATION
EQUIPMENT CONNECTION; COORDINATE CONNECTION WITH EQUIPMENT
PRIOR TO ROUGH-IN
MOTOR CONNECTION
CEILING MOUNTED DUPLEX RECEPTACLE (COORDINATE PLACEMENT WITH
CEILING EQUIPMENT PRIOR TO ROUGH-IN)
DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED BELOW 5FT
GFCI-TYPE DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED BELOW 5FT
DOUBLE-DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED BELOW 5FT
GFCI-TYPE DOUBLE-DUPLEX RECEPTACLE, UL TAMPER-RESISTANT WHERE MOUNTED
BELOW 5FT.
RECEPTACLE AND EQUIPMENT SUBSCRIPTS
AC ABOVE COUNTER
WP WEATHERPROOF (UL LISTED
WEATHER-RESISTANT)
42"MOUNTING HEIGHT AFF OR AFG
IG ISOLATED GROUND
S SURGE-PROTECTION TYPE
REF REFRIGERATOR
W WASHING MACHINE
D DRYER (30A-240V RATED RECPT.)
M MICROWAVE
HVAC THERMOSTAT OR SENSOR; PROVIDE & INSTALL BACKBOX,3/4" CONDUIT AND
CONDUCTORS TO ASSOCIATED HVAC UNIT. COORDINATE EXACT LOCATION & SIZE AND
NUMBER OF CONDUCTORS WITH M.C.
T SOR
SMALL EXHAUST FAN CONNECTION
TV 120V RECEPT. FOR TV; VERIFY HEIGHT WITH ARCH.
DRAWINGS & ELEVATIONS
USB 120V RECPT. WITH USB CHARGING PORTS
EWC ELECTRIC WATER COOLER; (SEE DETAIL. RECPT. SHALL
BE ACCESSIBLE, DO NOT MOUNT BEHIND HOUSING.)
DISP GARBAGE DISP. (UNDER SINK)
DW DISHWASHER (COORDINATE W/ MILLWORK, INSTALL PER
NEC 422.16(B)(2)).
M/R MICROWAVE/RANGE HOOD (COORDINATE W/ MILLWORK)
R ELECTRIC RANGE (50A-240V RATED RECPT.)
GENERAL SPECIAL SYSTEM NOTES:
A. ALL DEVICES SHOWN AT OR NEAR MILLWORK/CASEWORK SHALL BE COORDINATED WITH THE
ARCHITECTURAL ELEVATION DRAWINGS AND MILLWORK INSTALLER TO INSURE PROPER MOUNTING
HEIGHTS. CONTRACTOR SHALL ADJUST DEVICES AS NECESSARY IN ORDER TO POSITION DEVICES SUCH
THAT THEY WILL NOT FALL BEHIND MILLWORK, CABINETS OR BE DIRECTLY ABOVE SINKS OR MIDWAY
BETWEEN TILEWORK/WALL OR WAINSCOATING, ETC.
B. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO INSTALL A GFCI TYPE RECEPTACLE FOR ALL
RECPTACLES SHOWN IN TOILET RMS, BATHROOMS, KITCHENS/SERVING AREAS, ROOFTOP, OUTDOORS
OR WITHIN 6FT OF ANY SINK, BASIN, TUB OR FLOOR SINK AND ALL OTHER AREAS DEFINED BY THE NEC.
13053
ST ATE O F I D A HOSHAWNA.M E A D O R R E G I S TEREDRP
O F E S S I O N AL ENGIN
E
E
R
1823 E. Center
Pocatello, Idaho 83201
tel (208) 232-4439
www.payneengineeringinc.com
Engineering Inc.
Consulting Engineers
PROJECT NO.
DATE:
DRAWN BY:
CHECKED BY:
DRAWING NO.:
REVISIONS
PR
O
J
E
C
T
:
SH
E
E
T
T
I
T
L
E
:
SAM
TEP
P.E. #:2250
04/29/22 E0.0
21013
RE
X
B
U
R
G
F
M
O
F
F
I
C
E
/
J
R
.
S
E
M
I
N
A
R
Y
RE
X
B
U
R
G
I
D
A
H
O
N
O
R
T
H
S
T
A
K
E
EL
E
C
T
R
I
C
A
L
D
R
A
W
I
N
G
S
APRIL 2022
TO
I
L
E
T
R
O
O
M
A
D
D
I
T
I
O
N
F
O
R
:
PR
O
P
E
R
Y
N
O
.
5
1
1
-
3
0
6
7
A. ALL EXISTING ELECTRICAL MAY NOT APPEAR ON THESE
PLANS, HOWEVER THE ABOVE INFORMATION APPLIES.
B. PROVIDE AND INSTALL BLANK COVERS ON ALL UNUSED
SWITCH/OUTLET/J-BOXES WHERE REQUIRED.
C. ALL WALL DEVICES THAT ARE EXISTING TO REMAIN, SHALL
BE ADAPTED TO NEW WALL COVERINGS, REFER TO
ARCHITECTURAL DRAWINGS FOR EXACT WALL LOCATIONS,
THICKNESS, ETC.
D. PRIOR TO THE START OF ANY DEMOLITION WORK,
DISCONNECTING ANY POWER AND OR TELE/DATA SYSTEMS,
THE CONTRACTOR SHALL COORDINATE DOWN-TIME WITH
THE OWNER.
E. REFER TO ARCHITECTURAL PLANS FOR EXTENT OF
DEMOLITION, DETAILS, ETC.
F. REMOVE OR RELOCATE ELECTRICAL AS NECESSARY FOR
NEW WORK.
G. WHERE EXISTING CIRCUITS ARE TO BE RE-USED, EXTEND AS
NECESSARY. MAINTAIN ELECTRICAL CONTINUITY TO
DOWNSTREAM EQUIPMENT TO REMAIN.
H. EXISTING SHOWN TO REMAIN, MAY NEED TO BE REMOVED
AND RE-INSTALLED ONLY AS NECESSARY FOR EXTENDING
OR MODIFICATION OF EXISTING CIRCUITS OR WIRING.
I. REFER TO MECHANICAL PLANS FOR EXTENT OF MECHANICAL
EQUIPMENT TO BE REMOVED OR RELOCATED.
J. REMOVE ALL UNUSED EQUIPMENT WIRING, CONDUIT AND
BOXES IN ALL AREAS. ABANDON ONLY IN CONCEALED
AREAS.
K. CONTRACTOR MY UTILIZE ANY EXISTING CONDUIT WHERE
COMPATIBLE WITH NEW DESIGN, AND IF IN GOOD CONDITION
AND COMPLIES WITH SPECIFICATIONS.
L. WHEN ANY MODIFICATIONS ARE MADE TO ANY EXISTING
ELECTRICAL PANEL TO REMAIN, CONTRACTOR TO PROVIDE
NEW TYPE WRITTEN INDEX TO REFLECT ALL NEW AND
EXISTING LOADS.
M. REMOVE ALL EQUIPMENT, RACEWAYS, CABLES,ETC. NOT
USED IN FINISHED AREAS.
GENERAL NOTES:
KEY NOTES:#
SCALE: 1/4" = 1'-0"2 NEW ELECTRICAL PLAN
8'4'0"
NORTH
SCALE: 1/4" = 1'-0"1 EXISTING ELECTRICAL PLAN
8'4'0"
NORTH
1 ALL EXISTING ELECTRICAL DEVICES IN THIS ROOM ARE TO
BE DISCONNECTED AND REMOVED INCLUDING BUT NOT
LIMITED TO; LIGHTS SWITCHES RECEPTACLES AND ETC.
REMOVE ALL ASSOCIATED CONDUIT/CONDUCTORS WHERE
POSSIBLE. LOCATE AND MAINTAIN EXISTING
LIGHTING/RECEPT. CIRCUIT(S) AS REQUIRED TO BE UTILIZED
FOR NEW DEVICES. MAINTAIN/RE-ESTABLISH CONTINUITY TO
ALL DOWNSTREAM EQUIPMENT/DEVICES THAT ARE TO
REMAIN.
2 EXISTING SOUND SYSTEM EQUIPMENT TO BE
DISCONNECTED AND REMOVED, EXISTING SPEAKER
CABLING SHALL BE PULLED BACK TO ABOVE ACCESSIBLE
CEILING SPACE, COILED AND ABANDONED. COORDINATE
WITH OWNER.
3 ALL EXISTING ELECTRICAL DEVICES AND EQUIPMENT IN THIS
ROOM TO REMAIN FUNCTIONAL, LOCATE AND PROTECT
DURING CONSTRUCTION.
4 EXISTING SQUARE D 225A MBR, NQO PANELBOARD TO
REMAIN.
5 CONNECT EXHAUST FAN TO ROOM LIGHTING CIRCUIT AND
CONTROL WITH LIGHTING
6 CONNECT TO EXISTING LIGHTING/RECPT. CIRCUIT MADE
AVAILABLE DURING DEMOLITION, FIELD VERIFY HOMERUN
LOCATION.
LIGHTING FIXTURE SCHEDULE
TYPE DESCRIPTION MOUNTING VOLTAGE LUMENS
COLOR
TEMP.(K) MFGR. CATALOG #
APPROVED
MFGR'S NOTES
F1 4FT LED WRAPAROUND SURFACE 120-277 4000 4000 LITHONIA FML4W-48-AL06-SEF-840-MVOLT COOPER
LIGHTING CONTROL/OCCUPANCY SENSOR SCHEDULE
TYPE DESCRIPTION MFGR. CATALOG # APPROVED EQUALS NOTES
OCC. SENSORS - CEILING (LINE VOLTAGE)
CD2 DUAL-TECHNOLOGY, LINE VOLTAGE, SMALL
MOTION 800W MAX LOAD
SENSOR SWITCH CMR PDT 9 COOPER, WATTSOPPER,
HUBBELL