HomeMy WebLinkAboutMECHANICAL & ELETRICAL SPECIFICATIONS - 97-00015 – Ricks College – Baseball Field & StructuresBASEBALL FIELD
RICKS COLLEGE CAMPUS
SW CORNER OF CENTER STREET AND 550 SOUTH STREET
REXBURG, IDAHO
MECHANICAL & ELECTRICAL SPECIFICATIONS
PREPARED BY:
ENGINEERED SYSTEMS, INC.
315 WEST CENTER
POCATELLO, IDAHO 83204
February 2, 1997
Z ri 1> j3tb
WARD + BLAKE ARCHITECTS
P.O. BOX 10399 - 310 EAST BROADWAY - JACKSON, WYOMING 83002 - (307) 733-6867 - FAX (307) 733-4741
DIVISION 15
MECHANICAL
15050 BASIC MECHANICAL MATERIALS & METHODS
15055 GENERAL MECHANICAL REQUIREMENTS
15083 POTABLE WATER PIPING INSULATION
15100 BUILDING SERVICES PIPING
15101 GENERAL PIPING REQURIEMENTS
15143 POTABLE WATER PIPING
15150 SANITARY WASTE & VENT PIPING
15400 PLUMBING FIXTURES & EQUIPMENT
15410 PLUMBING FIXTURES
1 Division 15
Ricks College Ballpark January 1997 Table of Contents
SECTION 15055
GENERAL MECHANICAL REQUIREMENTS
PART 1GENERAL
1.1 SUMMARY
A. Includes But Not Limited To
1. Responsibility for proper operation of mechanical equipment furnished under this
Division.
1.2 SUBMITTALS
A. See Section 01300.
B. Product Data
1. Submit Manufacturer's catalog data for each manufactured item.
a. Provide section in submittal for each type of item of equipment. Include
Manufacturer's catalog data of each manufactured item and enough information
to show compliance with Contract Document requirements. Literature shall show
capacities and size of equipment used and be marked indicating each specific
item with applicable data underlined.
b. Include name, address, and phone number of each supplier.
C. Shop Drawings
1. Provide schematic control diagrams for each separate fan system, heating system,
control panel, etc. Each diagram shall show locations of all control and operational
components and devices. Mark correct operating settings for each control device on
these diagrams.
2. Provide diagram for electrical control system showing wiring of related electrical control
items such as firestats, fuses, interlocks, electrical switches, and relays. Provide
drawings showing electrical power requirements and connection locations.
3. Provide drawing of each temperature control panel identifying components in panels and
their function.
4. Provide other shop drawings required by Division 15 trade Sections.
D. Closeout Submittals
1. See Section 01700.
2. Submit record drawings. Record differences between mechanical work as installed and
as shown in Contract Documents.
3. Operation & Maintenance Manual Data -
a. Modify and add to requirements of Section 01700 as follows -
1) At beginning of MECHANICAL section of Operations & Maintenance
Manual, provide master index showing items included.
2) Provide name, address, and phone number of Architect, Architect's
Mechanical Engineer, General Contractor, and Mechanical, Plumbing,
Sheet Metal, Refrigeration, Fire Protection, and Temperature Control
subcontractors.
3) Provide operating instructions to include -
a) General description of each plumbing, mechanical, and fire
protection system.
b) Step by step procedure to follow in putting each piece of
mechanical equipment into operation.
2 15055
Ricks College Ballpark January 1997 General Mechanical Requirements
4) Maintenance instructions shall include -
a) List of mechanical equipment used indicating name, model, serial
number, and name plate data of each item together with number
and name associated with each system item.
b) Manufacturer's maintenance instructions for each piece of
mechanical equipment installed in Project. Instructions shall
include name of vendor, installation instructions, parts numbers &
lists, operation instructions of equipment, and maintenance &
lubrication instructions.
1.3 QUALITY ASSURANCE
A. Requirements of Regulatory Agencies
1. Perform work in accordance with applicable provisions of local Plumbing Code, Gas
Ordinances, and adoptions thereof. Provide materials and labor necessary to comply
with rules, regulations, and ordinances.
2. In case of differences between building codes, state laws, local ordinances, utility
company regulations, and Contract Documents, the most stringent shall govern.
Promptly notify Architect in writing of such differences.
1.4 WARRANTIES
A. In addition to guarantee specified in General Conditions, guarantee heating, cooling, and
plumbing systems to be free from noise in operation that may develop from failure to construct
system in accordance with Contract Documents.
B. Provide certificates of warranty for each piece of equipment made out in favor of Owner.
Clearly record 'start-up' date of each piece of equipment on certificate. Include certificates as
part of Operation & Maintenance Manual.
PART 3 EXECUTION
3.1 EXAMINATION
A. Site Inspection
1. Examine premises to understand conditions which may affect performance of work of
this Division before submitting proposals for this work.
2. No subsequent allowance for time or money will be considered for any consequence
related to failure to examine site conditions.
B. Drawings
1. Plumbing and Mechanical Drawings show general arrangement of piping, ductwork,
equipment, etc. Follow as closely as actual building construction and work of other
trades will permit.
2. Consider Architectural and Structural Drawings part of this work insofar as these
drawings furnish information relating to design and construction of building. These
drawings take precedence over Plumbing and Mechanical Drawings.
3. Because of small scale of Drawings, it is not possible to indicate all offsets, fittings, and
accessories which maybe required. Investigate structural and finish conditions affecting
this work and arrange work accordingly, providing such fittings, valves, and accessories
required to meet conditions.
C. Ensure that items to be furnished fit space available. Make necessary field measurements to
ascertain space requirements including those for connections and furnish and install equipment
of size and shape so final installation shall suit true intent and meaning of Contract Documents.
If approval is received by Addendum or Change Order to use other than originally specified
items, be responsible for specified capacities and for ensuring that items to be furnished will
fit space available.
3 15055
Ricks College Ballpark January 1997 General Mechanical Requirements
3.2 INSTALLATION
A. Interface With Other Work
1. Electrical - Furnish exact location of electrical connections and complete information
on motor controls to installer of electrical system.
B. Cut carefully to minimize necessity for repairs to previously installed or existing work. Do not
cut beams, columns, or trusses.
C. Arrange pipes, ducts, and equipment to permit ready access to valves, unions, traps, filters,
starters, motors, control components, and to clear openings of doors and access panels.
D. Sealants
1. Install firestopping material to seal penetrations through fire rated structures and draft
stops.
2. Seal openings through building exterior caused by penetrations of elements of
mechanical systems.
3. Furnish and install acoustical sealant to seal penetrations through acoustically insulated
walls and ceilings.
3.3 REPAIR/RESTORATION
A. Patch and repair walls, floors, ceilings, and roofs with materials of same quality and
appearance as adjacent surfaces unless otherwise shown. Surface finishes shall exactly
match existing finishes of same materials.
B. Each Section of this Division shall bear expense of cutting, patching, repairing, and replacing
of work of other Sections required because of its fault, error, tardiness, or because of damage
done by it.
C. Cutting, patching, repairing, and replacing pavements, sidewalks, roads, and curbs to permit
installation of work of this Division is responsibility of Section installing work.
3.4 ADJUSTMENT
A. Properly lubricate equipment before Owner's acceptance.
B. Repair damaged finishes and leave everything in working order.
3.5 CLEANING
A. Clean exposed piping, ductwork, equipment, and fixtures. Remove stickers from fixtures and
adjust flush valves.
END OF SECTION
4 15055
Ricks College Ballpark January 1997 General Mechanical Requirements
SECTION 15083
POTABLE WATER PIPE INSULATION
PART 1 GENERAL
1.1 SUMMARY
A. Includes But Not Limited To
1. Furnish and install insulation on hot and cold water lines, fittings, valves, and
accessories as described in Contract Documents.
PART 2 PRODUCTS
2.1 INSULATION
A. For Above Grade Piping
1. One inch thick snap -on glass fiber pipe insulation.
2. Heavy density pipe insulation with factory vapor jacket equal to Fiberglas ASJ may be
used.
3. Approved Manufacturers -
a. Schuller
b. Owens-Corning
C. Knauf
4. PVC Fitting, Valve, & Accessory Covers -
a. Approved Manufacturers
1) Knauf
2) Zeston
B. For Below Grade Piping
1. 112 inch thick
2. Approved Manufacturers -
a. DG Tubolit by Armstrong
b. ImcoLock or ImcoShield by Imcoa
C. Therma-Cel by Rubatex
3. Joint Sealant -
a. Armstrong 520
b. Rubatex R-373
PART 3 EXECUTION
3.1 APPLICATION
A. Above Grade Piping
1. Apply insulation to clean, dry piping with joints tightly butted.
2. Adhere 'factory applied vapor barrier jacket lap' smoothly and securely at longitudinal
laps with a white vapor barrier adhesive. Adhere 3 inch wide self-sealing butt joint strips
over end joints.
3. Fittings, Valves, & Accessories -
a. Insulate with same type and thickness of insulation as pipe, with ends of
insulation tucked snugly into throat of fitting and edges adjacent to pipe insulation
tufted and tucked in.
b. Cover insulation with one piece fitting cover secured by stapling or taping ends
to adjacent pipe covering.
5 15083
Ricks College Ballpark January 1997 Potable Water Pipe Insulation
C. Alternate Method - Insulate fittings, valves, and accessories with one inch of
insulating cement and vapor seal with two 1/8 inch wet coats of vapor barrier
mastic reinforced with glass fabric extending 2 inches onto adjacent insulation.
4. Pipe Hangers -
a. Do not allow pipes to come in contact with hangers.
b. Provide 16 ga by 6 inch long galvanized shields at each pipe hanger to protect
pipe insulation from crushing by clevis hanger.
Below Grade Piping - Slip underground pipe insulation onto pipe and seal butt joints. Where
slip-on technique is not possible, slit insulation, apply to pipe, and seal seams and joints.
END OF SECTION
6 15083
Ricks College Ballpark January 1997 Potable Water Pipe Insulation
SECTION 15101
GENERAL PIPING REQUIREMENTS
PART 1 GENERAL
1.1 SUMMARY
A. Includes But Not Limited To
1. General piping installation procedures applicable to all piping systems.
B. Related Sections
1. Section 15055 - General Mechanical Requirements
PART 2 PRODUCTS
2.1 PIPE & PIPE FITTINGS
A. Use domestic made pipe and pipe fittings on Project. Weld-O-Let and Screw-0-Let fittings are
acceptable.
2.2 VALVES
A. Valves of same type shall be of same manufacturer.
2.3 PIPE HANGERS
A. Adjustable, malleable iron clevis type, swivel loop type, or swivel split ring type of a diameter
adequate to support pipe size.
B. Approved Manufacturers
1. B-Line Systems
2. Grinnell
3. Michigan Hanger Co
4. Superstrut
2.4 DI -ELECTRIC UNIONS
A. Suitable for at least 175 PSIG WP at 250 deg F.
B. Approved Manufacturers
1. EPCO
2. Victaulic Cc
3. Watts Regulator Co
2.5 SLEEVES
A. Standard weight galvanized iron pipe, Schedule 40 PVC, or 14 gauge galvanized sheet metal
two sizes larger than pipe or insulation.
7 15101
Ricks College Ballpark January 1997 General Piping Requirements
PART 3 EXECUTION
3.1 INSTALLATION
A. Furnish and install complete system of piping, valved as indicated or as necessary to
completely control entire apparatus.
1. Pipe drawings are diagrammatic and indicate general location and connections. Piping
may have to be offset, lowered, or raised as required or directed at site. This does not
relieve this Division from responsibility for proper erection of systems of piping in every
respect.
2. Arrange piping to not interfere with removal of other equipment, ducts, or devices, or
block access to doors, windows, or access openings. Provide accessible, ground joint
unions in piping at connections to equipment.
3. Install piping systems so they may be easily drained.
4. Do not install piping in shear walls.
B. Properly support piping and make adequate provisions for expansion, contraction, slope, and
anchorage.
1. Cut piping accurately for fabrication to measurements established at site and work into
place without springing or forcing. Do not use pipe hooks, chains, or perforated metal
for pipe support. Remove burr and cutting slag from pipes.
2. Make changes in direction with proper fittings.
3. Insulate hangers for copper pipe from piping by means of at least two layers of Scotch
33 plastic tape.
4. Support piping at 8 feet on center maximum for pipe 1-1/4 inches or larger and 6 feet
on center maximum for pipe 1-1/8 inch or less. Provide support at each elbow. Install
additional support as required.
5. Except underground pipe, suspend piping from roof trusses or clamp to vertical walls
using Unistrut and clamps. Laying of piping on any building member is not allowed.
C. Make connections of dissimilar metals with di -electric unions. Do not use reducing bushings,
street elbows, bull head tees, or close nipples.
D. Provide sleeves around pipes passing through concrete or masonry floors, walls, partitions,
or structural members. Do not place sleeves around soil, waste, vent, or roof drain lines
passing through concrete floors on grade. Seal sleeves with specified sealants.
E. Cap or plug open ends of pipes and equipment to keep dirt and other foreign materials out of
system. Do not use plugs of rags, wool, cotton waste, or similar materials.
END OF SECTION
8 15101
Ricks College Ballpark January 1997 General Piping Requirements
SECTION 15143
POTABLE WATER PIPING
PART 1 GENERAL
1.1 SUMMARY
A. Includes But Not Limited To
1. Perform excavating and backfilling required by work of this Section.
2. Furnish and install potable water piping complete with necessary valves, connections,
and accessories inside building and connect with outside utility lines 5 feet from building
perimeter as described in Contract Documents.
PART 2 PRODUCTS
2.1 COMPONENTS
A. Pipe
1. Meet requirements of ASTM B 88.
a. Type K for underground or beneath concrete slab. 3/4 inch minimum under
slabs.
b. Type L for above ground applications.
B. Fittings - Wrought copper.
C. Connections
1. Above -Grade - Sweat copper type with 95/5 or 96/4 Tin -Antimony solder or Silvabrite
100 solder. Use only lead-free solder.
2. Below Grade -
a. Brazed using following type rods.
1) Copper to Copper Connections -
a) AWS Classification BCuP-4 Copper Phosphorus (6 percent silver).
b) AWS Classification BCuP-5 Copper Phosphorus (15 percent
silver).
2) Copper to Brass or Copper to Steel Connections - AWS Classification
BAg-5 Silver (45 percent silver).
3) Do not use rods containing Cadmium.
b. Brazing Flux -
1) Approved Manufacturers -
a) Stay -Silt' white brazing flux by J W Harris Co
b) High quality silver solder flux by Handy & Harmon
C. Joints under slabs acceptable only if allowed by local codes.
D. Ball Valves
1. Use ball valves exclusively unless otherwise specified. Ball valves shall be by single
manufacturer from approved list below. Valves shall be two piece, full port for 150 PSI
SWP.
2. Quality Standard - Nibco-Scott T585 or S585
3. Approved Manufacturers -
a. ConBraCo 'Apollo'
b. Hammond
C. Honeywell-Braukmann
d. Jenkins
e. Milwaukee
f. Nibco-Scott
9 15143
Ricks College Ballpark January 1997 Potable Water Piping
Stockham
Watts
E. Stop & Waste Valves
1. Approved Manufacturers & Models -
a. Mueller - Mark II Oriseal stop & waste valve H10288
b. Mueller - Buffalo screw type curb box H-10350 complete with lid and H-10349
enlarged base
F. Combination Pressure Reducing Valve/Strainer
1. Integral stainless steel strainer, or separate'Y' strainer installed upstream of pressure
reducing valve.
2. Built-in thermal expansion bypass check valve.
3. Quality Standard - Watts U513
4. Approved Manufacturers -
a. Cash Valve
b. Clay Valve - Hi Capacity
C. Con Braco 36C
d. Honeywell-Braukmann
e. Spence - Hi Capacity
f. Watts
g. Wilkins
PART 3 EXECUTION
3.1 INSTALLATION
A. Below Grade
1. Install piping under slabs without joints where possible.
2. Insulate water piping buried within building perimeter.
3. Bury water piping 6 inches minimum below bottom of slab and encase in 2 inches
minimum of sand.
B. Locate cold water lines a minimum of 6 inches from hot water line.
3.2 FIELD QUALITY CONTROL
A. Site Tests - Before pipes are covered, test systems in presence of Architect at 100 psi
hydrostatic pressure for two hours and show no leaks.
3.3 CLEANING
A. Sterilize potable water system with solution containing 200 parts per million minimum of
available chlorine and maintaining pH of 7.5 minimum. Introduce chlorinating materials into
system in manner approved by Architect. Allow sterilization solution to remain for 24 hours and
open and close valves and faucets several times during that time.
B. After sterilization, flush solution from system with clean water until residual chlorine content is
less than 0.2 parts per million.
C. Water system will not be accepted until negative bacteriological test is made on water taken
from system. Repeat dosing as necessary until such negative test is accomplished.
END OF SECTION
10 15143
Ricks College Ballpark January 1997 Potable Water Piping
SECTION 15150
SANITARY WASTE & VENT PIPING
PART 1 GENERAL
1.1 SUMMARY
A. Includes But Not Limited To
1. Furnish and install soil, waste, and vent piping systems within building and connect with
outside utility lines 5 feet out from building where applicable.
2. Perform excavation and backfill required by work of this Section.
PART 2 PRODUCTS
2.1 MATERIAL
A. Buried Lines
1. Minimum size of waste piping installed under floor slab on grade shall be 2 inches.
2. Service weight, BAS-DWV pipe and fittings meeting requirements of Idaho State
Plumbing Code.
B. Above Grade Piping & Vent Lines
1. Service weight, ABS-DWV pipe and fittings.
PART 3 EXECUTION
3.1 INSTALLATION
A. Do not calk threaded work.
B. Grade soil and waste lines within building perimeter 1/4 inch fall per ft in direction of flow.
C. Install piping so cleanouts may be installed as follows
1. Where shown on Drawings and near bottom of each stack and riser.
2. At every 135 degrees of accumulative change in direction for horizontal lines.
3. Every 100 feet of horizontal run.
4. Extend piping to accessible surface. Do not install piping so cleanouts must be installed
in carpeted floors. In such locations, configure piping so wall type cleanouts may be
used.
D. Each fixture and appliance discharging water into sanitary sewer or building sewer lines shall
have seal trap in connection with complete venting system so gasses pass freely to
atmosphere with no pressure or syphon condition on water seal.
E. Vent entire waste system to atmosphere. Discharge 14 inches above roof. Join lines together
in fewest practicable number before projecting above roof. Set back vent lines so they will not
pierce roof near edge or valley.
F. Use torque wrench to obtain proper tension in cinch bands when using hubless cast iron pipe.
Butt ends of pipe against centering flange of coupling.
11 15150
Ricks College Ballpark January 1997 Sanitary Waste & Vent Piping
3.2 FIELD QUALITY CONTROL
A. Site Tests - After backfilling and compacting of trenches is complete but before placing floor
slab, conduct tests for leaks and defective work. Notify Architect prior to testing. Fill waste and
vent system to roof level with water, 10 feet minimum, and show no leaks for two hours.
Correct leaks and defective work.
END OF SECTION
12 15150
Ricks College Ballpark January 1997 Sanitary Waste & Vent Piping
SECTION 15410
PLUMBING FIXTURES
PART 1 GENERAL
1.1 SUMMARY
A. Includes But Not Limited To
1. Furnish and install plumbing fixtures as described in Contract Documents.
B. Related Sections
1. Section 15055 - General Mechanical Requirements
PART 2 PRODUCTS
2.1 GENERAL
A. Interior exposed pipe, valves, and fixture trim, including trim behind custom casework doors,
shall be chrome plated.
B. Do not use flexible water piping.
PART 3 EXECUTION
3.1 INSTALLATION
A. Install fixtures including traps and accessories with accessible stop or control valve in each hot
and cold water branch supply line.
B. Make fixture floor connections with approved brand of cast iron floor flange, soldered or calked
securely to waste pipe. Make joints between fixtures and floor flanges tight with approved
fixture setting compound or gaskets. Calk between fixtures and wall and floor with white butyl
rubber non -absorbent sealant. Point edges.
3.2 CLEANING
A. Polish chrome finish at completion of Project.
END OF SECTION
13 15410
Ricks College Ballpark January 1997 Plumbing Fixtures
16000 DIVISION 16 - ELECTRICAL WORK
16010
BASIC ELECTRICAL REQUIREMENTS: ..........................................
2
16111
CONDUIT: ...................................................................
3
16123
WIRE AND CABLE: ...........................................................
5
16130
BOXES: .....................................................................
7
16141
WIRING DEVICES: ............................................................
9
16170
GROUNDING AND BONDING: .................................................
11
16190
SUPPORTING DEVICES: ......................................................
12
16195
ELECTRICAL IDENTIFICATION: ..............................................
13
16470
PANELBOARDS:............................................................
14
16510
INTERIOR LUMINAIRES: .............................. ......................
17
16530
EXTERIOR LUMINAIRES: ....................................................
19
Ricks College Ballpark 1 16000
October 1996 Table of Contents
16010 BASIC ELECTRICAL REQUIREMENTS
PART GENERAL
1.01 SECTION INCLUDES
A. Basic Electrical Requirements specifically applicable to Division 16 Sections.
1.02 ALTERNATES
A. Alternates quoted on Bid Forms will be reviewed and accepted or rejected at the Engineer's option.
B. Coordinate related work and modify surrounding work as required.
1.03 REFERENCES
A. ANSI/NFPA 70 - National Electrical Code (NEC).
1.04 SUBMITTALS
A. Proposed Products List: Include Products specified in the following Sections:
1. Section 16141-Wiring Devices.
2. Section 16470-Panelboards.
3. Section 16510-Interior Luminaires.
4. Section 16530-Exterior Luminaires.
5. Section 16741-Telephone System.
B. Submit shop drawings and product data grouped to include complete submittals of related systems, products,
and accessories in a single submittal.
C. Mark dimensions and values in units to match those specified.
1.05 REGULATORY REQUIREMENTS
A. Electrical: Conform to NEC.
B. Obtain permits, and request inspections from authority having jurisdiction.
1.06 PROJECT/SITE CONDITIONS
A. Install Work in locations shown on Drawings, unless prevented by Project conditions.
B. Prepare drawings showing proposed rearrangement of Work to meet Project conditions, including changes to
Work specified in other Sections. Obtain permission of Owner before proceeding.
END OF SECTION
Ricks College Ballpark 2 16010
October 1996 Basic Electrical Requirements
16'_ 11 CONDUIT:
PART1 GENERAL
1.01 SECTION INCLUDES
A. Metal conduit.
B. Nonmetal conduit.
C. Fittings.
1.02 RELATED SECTIONS
A. Section 16130 - Boxes.
B. Section 16170 - Grounding and Bonding.
C. Section 16190 - Supporting Devices.
D. Section 16195 - Electrical Identification.
1.03 DESIGN REQUIREMENTS
A. Conduit Size: ANSI/NEC.
1.04 PROJECT RECORD DOCUMENTS
A. Accurately record actual routing of conduits.
1.05 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
1.06 DELIVERY, STORAGE, AND HANDLING
A. Accept conduit on site. Inspect for damage.
B. Protect conduit from corrosion and entrance of debris by storing above grade. Provide appropriate covering.
C. Protect PVC conduit from sunlight.
1.07 PROJECT CONDITIONS
A. Verify that field measurements are as shown on Drawings.
B. Verify routing and termination locations of conduit prior to rough -in.
C. Conduit routing is shown on Drawings in approximate locations unless dimensioned. Route as required to
complete wiring system.
PART 2 PRODUCTS
2.01 CONDUIT REQUIREMENTS
A. Minimum Size: 3/4 inch unless otherwise specified.
B. Underground Installations:
I . Use rigid steel conduit or thickwall nonmetallic conduit with rigid steel elbows.
C. Outdoor Locations Above Grade: Use rigid steel conduit.
D. Wet and Damp Locations: Use rigid steel conduit.
E. Dry Locations:
I . Concealed: Use rigid steel conduit or electrical metallic tubing.
Ricks College Ballpark 3 161 1 1
October 1996 Conduit
2. Exposed: Use rigid steel conduit where mechanical damage may occur to a height of 5'0" above floor;
in other areas use electrical metallic tubing.
2.02 METAL CONDUIT
A. Rigid Steel Conduit: ANSI C80.1.
B. Electrical Metallic Tubing.
C. Fittings and Conduit Bodies: ANSI/NEMA FB 1; material to match conduit.
2.03 NONMETALLIC CONDUIT
A. Description: NEMA TC 2; Schedule 40 PVC.
B. Fittings and Conduit Bodies: NEMA TC 3.
PART 3 EXECUTION
3.01 INSTALLATION
A. Install conduit in accordance with NECA "Standard of Installation."
B. Install nonmetallic conduit in accordance with manufacturer's instructions.
C. Arrange supports to prevent misalignment during wiring installation.
D. Route exposed conduit parallel and perpendicular to walls.
E. Maintain adequate clearance between conduit and piping.
F. Maintain 12 inch clearance between conduit and surfaces with temperatures exceeding 104 degrees F.
G. Cut conduit square using saw or pipecutter; de -burr cut ends.
H. Bring conduit to shoulder of fittings; fasten securely.
I. Join nonmetallic conduit using cement as recommended by manufacturer. Wipe nonmetallic conduit dry and
clean before joining. Apply full even coat of cement to entire area inserted in fitting. Allow joint to cure for 20
minutes, minimum.
J. Use conduit hubs to fasten conduit to sheet metal boxes in damp and wet locations and to cast boxes.
K. Install no more than equivalent of three 90-degree bends between boxes. Use conduit bodies to make sharp
changes in direction, as around beams. Use hydraulic one-shot bender to fabricate bends in metal conduit.
L. Avoid moisture traps; provide junction box with drain fitting at low points in conduit system.
M. Use suitable caps to protect installed conduit against entrance of dirt and moisture.
N. Ground and bond conduit under provisions of Section 16170.
O. Identify conduit under provisions of Section 16195.
END OF SECTION
Ricks College Ballpark 4 16111
October 1996 Conduit
16123 WIRE AND CABLE:
PART1 GENERAL
1.01 SECTION INCLUDES
A. Building wire and cable.
B. Service entrance cable.
C. Wiring connectors and connections.
1.02 RELATED SECTIONS
A. Section 16111 - Conduit.
B. Section 16130 - Boxes.
C. Section 16195 - Identification.
1.03 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
1.04 PROJECT CONDITIONS
A. Verify that field measurements are as shown on Drawings.
B. Conductor sizes are based on copper.
C. Wire and cable routing shown on Drawings is approximate unless dimensioned. Route wire and cable as
required to meet Project Conditions.
D. Where wire and cable routing is not shown, and destination only is indicated, determine exact routing and
lengths required.
1.05 COORDINATION
A. Determine required separation between cable and other work.
B. Determine cable routing to avoid interference with other work.
PART 3 EXECUTION
3.01 EXAMINATION
A. Verify that interior of building has been protected from weather.
B. Verify that mechanical work likely to damage wire and cable has been completed.
3.02 PREPARATION
A. Completely and thoroughly swab raceway before installing wire.
3.03 WIRING METHODS
A. All Interior Locations: Use only building wire THW/THWN/XHHW insulation in raceway.
B. All Exterior Locations: Use only building wire THW/THWN, XHHW insulation , telephone cable, or
service -entrance cable in raceway.
3.04 INSTALLATION
A. Install products in accordance with manufacturers instructions.
Ricks College Ballpark 5 16123
October 1996 Wire and Cable
B. Use solid conductor for feeders and branch circuits 10 AWG and smaller.
C. Use conductor not smaller than 12 AWG for power and lighting circuits.
D. Use 10 AWG conductors for 20 ampere, 120 volt branch circuits longer than 75 feet.
E. Pull all conductors into raceway at same time.
F. Use suitable wire pulling lubricant for building wire 4 AWG and larger.
G. Use suitable cable fittings and connectors.
H. Neatly train and lace wiring inside boxes, equipment, and panelboards.
I. Clean conductor surfaces before installing lugs and connectors.
J. Make splices,taps, and terminations to carry full ampacity of conductors with no perceptible temperature rise.
K. Use split bolt connectors for copper conductor splices and taps, 6 AWG and larger. Tape uninsulated conductors
and connector with electrical tape to 150 percent of insulation rating of conductor,
L. Use solderless pressure connectors with insulating covers for copper conductor splices and taps, 8 AWG.
M. Use insulated spring wire connectors with plastic caps for copper conductor splices and taps, 10 AWG and
smaller.
3.05 INTERFACE WITH OTHER PRODUCTS
A. Identify wire and cable under provisions of Section 16195.
B. Identify each conductor with its circuit number or other designation indicated on Drawings.
3.06 FIELD QUALITY CONTROL
A. Inspect wire and cable for physical damage and proper connection.
B. Measure tightness of bolted connections and compare torque measurements with manufacturer's recommended
values.
C. Verify continuity of each branch circuit conductor.
END OF SECTION
Ricks College Ballpark 6 16123
October 1996 Wire and Cable
16130 BOXES:
PARTI GENERAL
1.01 SECTION INCLUDES
A. Wall outlet boxes.
B. Pull and junction boxes.
1.02 RELATED SECTIONS
A. Section 16141 - Wiring Devices.
1.03 PROJECT RECORD DOCUMENTS
A. Accurately record actual locations and mounting heights of outlet, pull, and junction boxes.
1.04 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
1.05 PROJECT CONDITIONS
A. Verify field measurements are as shown on Drawings.
B. Verify locations of outlets in work areas prior to rough -in.
C. Electrical boxes are shown on Drawings in approximate locations unless dimensioned. Install at location
required for box to serve intended purpose.
PART 2 PRODUCTS
2.01 OUTLET BOXES
A. Sheet Metal Outlet Boxes: ANSI/NEMA OS 1, galvanized steel.
1. Luminaire and Equipment Supporting Boxes: Rated for weight of equipment supported; include 1/2
inch male fixture studs where required.
B. Cast Boxes: NEMA FB 1, Type FD , cast feralloy. Provide gasketed cover by box manufacturer.
2.02 PULL AND JUNCTION BOXES
A. Sheet Metal Boxes: NEMA OS 1, galvanized steel.
B. Surface -Mounted Cast Metal Box: NEMA 250, Type 4; flat -flanged, surface -mounted junction box.
I. Material: Cast aluminum.
2. Cover: Furnish with ground flange, neoprene gasket, and stainless steel cover screws.
Ricks College Ballpark 7 16130
October 1996 Boxes
PART 3 EXECUTION
3.01 INSTALLATION
A. Install electrical boxes as shown on Drawings, and as required for splices, taps, wire pulling, equipment
connections and compliance with regulatory requirements.
B.
Install electrical boxes to maintain headroom and to present neat mechanical appearance.
C. Install
pull boxes and junction boxes above accessible ceilings and in unfinished areas only.
D.
Inaccessible Ceiling Areas: Install outlet and junction boxes no more than 6 inches from ceiling access panel
or from removable recessed luminaire.
E.
Install boxes to preserve fire resistance rating of partitions and other elements.
F.
Align adjacent wall -mounted outlet boxes for switches and similar devices with each other.
G.
Use flush mounting outlet boxes in finished areas.
H.
Do not install flush mounting boxes back-to-back in walls; provide minimum 6 inch separation.
I.
Secure flush mounting box to interior wall and partition studs. Accurately position to allow for
surface finish thickness.
J.
Use stamped steel bridges to fasten flush mounting outlet box between studs.
K.
Install flush mounting box without damaging wall insulation or reducing its effectiveness.
L.
Support boxes independently of conduit.
M.
Use gang box where more than one device is mounted together. Do not use sectional box.
N.
Use gang box with plaster ring for single device outlets.
O.
Use cast outlet box in exterior locations exposed to the weather and wet locations.
P.
Large Pull Boxes: Boxes larger than 100 cubic inches in volume or 12 inches in any dimension.
I. Interior Dry Locations: Use hinged enclosure.
2. Other Locations: Use surface -mounted cast metal box.
3.02 INTERFACE WITH OTHER PRODUCTS
A. Coordinate locations and sizes of required access doors with other Work.
B. Mounting heights and locations of outlets shall be as shown on Drawings.
C. Position outlet boxes to locate luminaires as shown on Drawings.
3.03 ADJUSTING
A. Adjust flush -mounting outlets to make front flush with finished wall material.
B. Install knockout closure in unused box opening.
END OF SECTION
Ricks College Ballpark 8 16130
October 1996 Boxes
16141 WIRING DEVICES:
PART1 GENERAL
1.01 SECTION INCLUDES
A. Wall switches.
B. Receptacles.
C. Device plates and decorative box covers.
D. Telephone receptacle.
1.02 RELATED SECTIONS
A. Section 16130 - Boxes.
1.03 SUBMITTALS
A. Product Data: Provide manufacturer's catalog information showing dimensions, colors, and configurations.
B. Manufacturer's Instructions:
1. Indicate application conditions and limitations of use stipulated by product testing agency specified
under regulatory requirements.
2. Include instructions for storage, handling, protection, examination, preparation, operation and
installation of product.
1.04 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
PART 3 EXECUTION
3.01 EXAMINATION
A. Verify receptacle and telephone outlet boxes are installed at 18 inches and switch outlet boxes at 48 inches to
center above finished floor.
B. Verify wall openings are neatly cut and will be completely covered by wall plates.
C. Verify branch circuit wiring installation is completed, tested, and ready for connection to wiring devices.
3.02 PREPARATION
A. Provide extension rings to bring outlet boxes flush with finished surface.
B. Clean debris from outlet boxes.
3.03 INSTALLATION
A. Install products in accordance with manufacturer's instructions.
B. Install devices plumb and level.
C. Install switches with OFF position down.
D. Install receptacles with grounding pole on top.
E. Connect wiring device grounding terminal to outlet box with bonding jumper.
F. Install decorative plates on switch, receptacle, and blank outlets in finished areas.
G. Connect wiring devices by wrapping conductor around screw terminal.
H. Install galvanized steel plates on outlet boxes and junction boxes in unfinished areas.
Ricks College Ballpark 9 16141
October 1996 Wiring Devices
3.04 FIELD QUALITY CONTROL
A. Inspect each wiring device for defects.
B. Operate each wall switch with circuit energized and verify proper operation.
C. Verify that each receptacle device is energized.
D. Test each receptacle device for proper polarity.
E. Test each GFCI receptacle device for proper operation.
F. Verify that telephone jack is properly connected and circuit is operational.
3.05 ADJUSTING
A. Adjust devices and wall plates to be flush and level.
END OF SECTION
Ricks College Ballpark 10 16141
October 1996 Wiring Devices
16170 GROUNDING AND BONDING:
PART1 GENERAL
1.01 SECTION INCLUDES
A. Grounding electrodes and conductors.
B. Equipment grounding conductors.
C. Bonding.
1.02 GROUNDING ELECTRODE SYSTEM
A. Driven ground rod - see Drawings.
1.03 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
PART 2 PRODUCTS
2.01 WIRE
A. Material: Stranded copper.
B. Grounding Electrode Conductor: Size as indicated on Drawings.
PART 3 EXECUTION
3.01 EXAMINATION
A. Verify that final backfill and compaction has been completed before driving rod electrodes.
3.02 INSTALLATION
A. Install Products in accordance with manufacturer's instructions.
3.03 FIELD QUALITY CONTROL
A. Inspect grounding and bonding system conductors and connections for tightness and proper installation.
END OF SECTION
Ricks College Ballpark 11 16170
October 1996 Grounding and Bonding
16190 SUPPORTING DEVICES:
PART1 GENERAL
1.01 SECTION INCLUDES
A. Conduit and equipment supports.
B. Anchors and fasteners.
1.02 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Fumish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
PART PRODUCTS
2.01 PRODUCT REQUIREMENTS
A. Materials and Finishes: Provide adequate corrosion resistance.
B. Provide materials, sizes, and types of anchors, fasteners and supports to carry the loads of equipment and
conduit. Consider weight of wire in conduit when selecting products.
C. Anchors and Fasteners:
1. Steel Structural Elements: Use beam clamps.
2. Concrete Surfaces: Use expansion anchors.
3. Plaster, and Gypsum Board Partitions: Use hollow wall fasteners.
4. Sheet Metal: Use sheet metal screws.
5. Wood Elements: Use wood screws.
2.02 STEEL CHANNEL
A. Description: Galvanized steel.
2.03 POWDER ACTUATED ANCHORS
2.04 SPRING STEEL CLIPS
A. Manufacturer:
1. Caddy.
PART 3 EXECUTION
3.01 INSTALLATION
A. Install products in accordance with manufacturer's instructions.
B. Provide anchors, fasteners, and supports in accordance with NECA "Standard of Installation".
C. Do not fasten supports to pipes, ducts, mechanical equipment, and conduit.
D. Obtain permission from Architect/Engineer before drilling or cutting structural members.
E. Fabricate supports from structural steel or steel channel. Rigidly weld members or use hexagon head bolts to
present neat appearance with adequate strength and rigidity. Use spring lock washers under all nuts.
F. Install surface -mounted cabinets and panelboards with minimum of four anchors.
G. In wet and damp locations use steel channel supports to stand cabinets and panelboards one inch off wall.
H. Use sheet metal channel to bridge studs above and below cabinets and panelboards recessed in hollow partitions,
END OF SECTION
Ricks College Ballpark 12 16190
October 1996 Supporting Devices
16195 ELECTRICAL IDENTIFICATION:
PART1 GENERAL
1.01 SECTION INCLUDES
A. Nameplates and labels.
B. Wire and cable markers.
C. Conduit markers.
1.02 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
PART2 PRODUCTS
2.01 NAMEPLATES AND LABELS
A. Nameplates: Engraved three -layer laminated plastic, white letters on black background.
B. Locations:
I. Each electrical distribution and control equipment enclosure.
C. Letter Size:
1. Use 1/8 inch letters for identifying individual equipment and loads.
2. Use 1/4 inch letters for identifying grouped equipment and loads.
2.02 WIRE MARKERS
A. Description: Tape type wire markers.
B. Locations: Each conductor at panelboard gutters, pull boxes, outlet and junction boxes, and each load
connection.
PART 3 EXECUTION
3.01 PREPARATION
A. Degrease and clean surfaces to receive nameplates and labels.
3.02 APPLICATION
A. Install nameplate and label parallel to equipment lines.
B. Secure nameplate to equipment front using adhesive.
END OF SECTION
Ricks College Ballpark 13 16195
October 1996 Electrucal Identification
16470 PANELBOARDS:
PART1 GENERAL
1.01 WORK INCLUDED
A. Service and distribution panelboards.
1.02 SUBMITTALS
A. Include outline and support point dimensions, voltage, main bus ampacity, integrated short circuit ampere rating,
circuit breaker arrangement and sizes.
1.03 SPARE PARTS
A. Keys: Furnish 3 each to Owner.
PART 2 PRODUCTS
2.01 ACCEPTABLE MANUFACTURES - PANELBOARDS
A. Square D.
B. General Electric.
C. Cutler -Hammer.
2.02 MAIN PANELBOARD
A. Panelboard: NEMA PB 1; circuit breaker type. FS W-P-115; Type I, Class 1.
B. Enclosure: NEMA PB 1; Type 1.
C. Cabinet Size: as indicated on Drawings.
D. Provide cabinet front with concealed trim clamps and hinged door with flush lock. Finish in manufacturer's
standard gray enamel.
E. Provide panelboard with aluminum bus, rating as scheduled on Drawings. Provide aluminum ground bus in all
panelboards.
F. Minimum Integrated Short Circuit Rating: as shown on Drawings.
G. Molded Case Circuit Breakers: NEMA AB 1; bolt -on type thermal magnetic trip circuit breakers, with common
trip handle for all poles. Provide circuit breakers UL listed as Type SWD for lighting circuits. Provide UL Class
A ground fault interrupter circuit breakers where scheduled on Drawings.
2.03 LOAD CENTER
A. Circuit breaker load center. FS W-P-115; Type I, Class 2.
B. Enclosure: General Purpose.
C. Provide surface box, with door, with lock on door. Finish in manufacturer's standard gray enamel.
D. Provide load center with bus rating as shown on Drawings.
E. Minimum Integrated Short Circuit Rating: as indicated on Drawings.
F. Molded Case Circuit Breakers: NEMA AB 1; plug -on type thermal magnetic trip circuit breakers, with common
trip handle for all poles. Provide UL Class A ground fault interrupter circuit breakers where scheduled on Drawings.
G. Do not use tandem circuit breakers.
PART 3 EXECUTION
3.01 INSTALLATION
Ricks College Ballpark 14 16470
October 1996 Panelboards
A. Install panelboards plumb with wall finishes, in conformance with NEMA PB I.I.
B. Height: 6 ft .
C. Provide filler plates for unused spaces in panelboards.
D. Provide typed circuit directory for each branch circuit panelboard. Revise directory to reflect circuiting changes
required to balance phase loads.
E. Stub 5 empty one inch conduits to accessible location out of each recessed panelboard.3.02 FIELD
QUALITY CONTROL
A. Measure steady state load currents at the panelboard feeder. Should the difference between phases exceed 20
percent, notify the Engineer. Take care to maintain proper phasing for multi -wire branch circuits.
B. Visual and Mechanical Inspection: Inspect for physical damage, proper alignment, anchorage, and grounding.
Check proper installation and tightness of connections for circuit breakers.
END OF SECTION
Ricks College Ballpark 15 16470
October 1996 Panelboards
16510 INTERIOR LUMINAIRES
PART1 GENERAL
1.01 SECTION INCLUDES
A. Interior luminaires and accessories.
B. Ballasts.
C. Lamps.
D. Luminaire accessories.
1.02 RELATED SECTIONS
A. Section 16130 - Boxes.
1.03 SUBMITTALS
A. Shop Drawings: Indicate dimensions and components for each luminaire that is not a standard product of the
manufacturer.
B. Product Data: Provide dimensions, ratings, and performance data.
C. Manufacturer's Instructions: Indicate application conditions and limitations of use stipulated by product testing
agency specified under Regulatory Requirements.
D. Manufacturer's Instructions: Include instructions for storage, handling, protection, examination, preparation,
and installation of product.
1.04 OPERATION AND MAINTENANCE DATA
A. Maintenance Data: Include replacement parts list.
1.05 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for
purpose specified and shown.
1.06 EXTRA MATERIALS
A. Provide two of each plastic lens.
B. Provide one replacement lamp for each 10 lamps installed.
C. Provide two of each ballast type.
PART 2 PRODUCTS
2.01 LUMINAIRES
A. Furnish products as specified on Drawings.
B. Install ballasts and specified accessories at factory.
Ricks College Ballpark 16 16510
October 1996 Interior Luminaires
PART 3 EXECUTION
3.01 EXAMINATION
A. Examine substrate and supporting grids for luminaires.
B. Examine each luminaire to determine suitability for lamps specified.
3.02 INSTALLATION
A. Install in accordance with manufacturers instructions.
B. Install surface mounted luminaires plumb and adjust to align with building lines and with each other. Secure
to prohibit movement.
C. Install wall mounted luminaires at height as scheduled.
D. Install accessories furnished with each luminaire.
E. Make wiring connections to branch circuits using building wire with insulation suitable for temperature
conditions within luminaire.
F. Bond products and metal accessories to branch circuit equipment grounding conductor.
G. Install specified lamps in each luminaire.
3.03 FIELD QUALITY CONTROL
A. Operate each luminaire after installation and connection. Inspect for proper connection and operation.
3.04 ADJUSTING
A. Aim and adjust luminaires as directed.
B. Relamp luminaires that have failed lamps at time of Substantial Completion.
3.05 CLEANING
A. Clean electrical parts to remove conductive and deleterious materials.
B. Remove dirt and debris from enclosure.
C. Clean photometric control surfaces as recommended by manufacturer.
D. Clean finishes and touch up damage.
END OF SECTION
Ricks College Ballpark 17 16510
October 1996 Interior Luminaires
16530 EXTERIOR LUMINAIRES:
PART GENERAL
1.01 SECTION INCLUDES
A. Exterior luminaires and accessories.
1.02 SUBMITTALS
A. Product Data: Provide dimensions, ratings, and performance data.
B. Manufacturer's Instructions: Indicate application conditions and limitations of use stipulated by product testing
agency specified under "Regulatory Requirements".
C. Manufacturer's Instructions: Include instructions for storage, handling, protection, examination, preparation,
installation, and starting of product.
1.03 OPERATION AND MAINTENANCE DATA
A. Maintenance Data: Include instructions for maintaining luminaires.
1.04 REGULATORY REQUIREMENTS
A. Conform to requirements of NEC.
B. Furnish products listed and classified by testing firm acceptable to authority having jurisdiction as suitable for purpose specified and
shown.
1.05 DELIVERY, STORAGE, AND HANDLING
A. Accept products on site. Inspect for damage.
1.06 EXTRA MATERIALS
A. Provide two spare lamps.
PART 2 PRODUCTS
2.01 LUMINAIRES
A. Furnish products as specified in schedule on Drawings.
PART 3 EXECUTION
3.01 EXAMINATION
A. Examine each luminaire to determine suitability for lamps specified.
3.02 INSTALLATION
A. Install in accordance with manufacturers' instructions.
B. In,`all lamps in each luminaire.
C. B id luminaires and metal accessories to branch circuit equipment grounding conductor.
3.03 FIELD QUALITY CONTROL
A. Operate each luminaire after installation and connection. Inspect for improper connections and operation.
Ricks College Ballpark 18 16530
October 1996 Exterior Luminaires
3.04 ADJUSTING
A. Relamp luminaires which have failed lamps at Date of Substantial Completion.
3.05 CLEANING
A. Clean electrical parts to remove conductive and deleterious materials.
B. Remove dirt and debris from enclosure.
C. Clean photometric control surfaces as recommended by manufacturer.
D. Clean finishes and touch up damage.
END OF SECTION
Ricks College Ballpark 19 16530
October 1996 Exterior Luminaires
�� ,- t�':�i,� ���