The URL can be used to link to this page

Home My WebLink AboutRESCHECK - 22-00080 - 1053 Cypress Loop - New SFR1ZGenerated by REScheck-Web Software Compliance Certificate Project carmack res Energy Code: 2018 IECC Location: Rexburg, Idaho Construction Type: Single-family Project Type: New Construction Conditioned Floor Area: 1,746 ft2 Glazing Area 14% Climate Zone: 6 (8693 HDD) Permit Date: Permit Number: Construction Site: Owner/Agent: tbd rexburg, ID 83440 Designer/Contractor: todd surely built Compliance: 4.5% Better Than Code Maximum UA: 335 Your UA: 320 The % Better or Worse Than Code Index reflects how close to compliance the house is based on code trade-off rules. It DOES NOT provide an estimate of energy use or cost relative to a minimum -code home. Slab -on -grade tradeoffs are no longer considered in the UA or performance compliance path in REScheck. Each slab -on -grade assembly in the specified climate zone must meet the minimum energy code insulation R-value and depth requirements. Envelope Assemblies Ceiling: Flat Ceiling or Scissor Truss 1,746 0.0 50.0 0.019 0.026 33 45 Wall: Wood Frame, 16" ox. 2,234 23.0 0.0 0.055 0.045 108 89 Door: Solid Door (under 50% glazing) 42 0.150 0.300 6 13 Window: Vinyl Frame 222 0.300 0.300 67 67 Basement Wall: Solid Concrete or Masonry Wall height: 9.0' 1,940 23.0 0.0 0,042 0.050 77 92 Depth below grade: 8.0' Insulation depth: 9.0' Window: Vinyl Frame 96 0.300 0.300 29 29 Compliance Statement. The proposed building design described here is consistent with the building plans, specifications, and other calculations submitted with the permit application. The proposed building has been designed to meet the 2018 IECC requirements in REScheck Version : REScheck-Web and to comply with the mandatory requirements listed in the REScheck Inspection Checklist. Name - Title Signature Date Project Title: carmack res Report date: 02/08/22 Data filename: Pagel of 9 REScheck Software Version : REScheck-Web Inspection Checklist Energy Code: 2018 IECC Requirements: 0.0% were addressed directly in the REScheck software Text in the "Comments/Assumptions" column is provided by the user in the REScheck Requirements screen. For each requirement, the user certifies that a code requirement will be met and how that is documented, or that an exception is being claimed. Where compliance is itemized in a separate table, a reference to that table is provided. Section # Pre-inspection/Plan Review Plans Verified Value Field Verified Value Complies? Comments/Assumptions & Req.ID 103.1, Construction drawings and ❑Complies 103.2 documentation demonstrate ❑Does Not [PRl]l ;energy code compliance for the ❑Not Observable building envelope. Thermal envelope represented on ❑Not Applicable construction documents. 103.1, I Construction drawings and ❑Complies 103.2, documentation demonstrate ❑Does Not 403.7 energy code compliance for ❑Not Observable [PR3]1 lighting and mechanical systems. Systems serving multiple ❑Not Applicable ` dwelling units must demonstrate ,compliance with the IECC 'Commercial Provisions. 302.1, Heating and cooling equipment is Heating: Heating: ❑Complies 403.7 sized per ACCA Manual S based Btu/hr Btu/hr ❑Does Not [PR2]2 on loads calculated per ACCA Cooling: Cooling: [-]Not Observable �?V Manual J or other methods approved by the code official. Btu/hr Btu/hr ❑Not Applicable Additional Comments/Assumptions: 11 High Impact (Tier 1) 2 1 Medium Impact (Tier 2) 3 1 Low Impact (Tier 3) Project Title: carmack res Report date: 02/08/22 Data filename: Page 2 of 9 Section # Foundation Inspection Plans Verified Value Field Verified Value Complies? Comments/Assumptions & Req.ID 402.1.1 Conditioned basement wall R. R- ❑Complies see the Envelope Assemblies [F0411 insulation R-value. Where interiorR_ R_ ❑Does Not table for values. j' insulation is used, verification ❑Not Observable may need to occur during ❑Not Applicable Insulation Inspection. Not ,required in warm -humid locations in Climate Zone 3. 303.2 Conditioned basement wall ❑Complies [F05]1 'insulation installed per FlDoes Not manufacturer's instructions. ':❑Not Observable ❑Not Applicable 402.2.9 Conditioned basement wall ft ft ❑Complies 5ee the Envelope Assemblies [F06]1 insulation depth of burial or ❑Does Not table for values. i distance from top of wall. ❑Not Observable ❑Not Applicable 303.2.1 A protective covering is installed ❑Complies [FO11]2 to protect exposed exterior ❑Does Not insulation and extends a ❑Not Observable minimum of 6 in. below grade. ❑Not Applicable 403.9 Snow- and ice -melting system ❑Complies [FO12]2 controls installed. '❑Does Not '❑Not Observable `❑Not Applicable Additional Comments/Assumptions: 11 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: carmack res Report date: 02/08/22 Data filename: Page 3 of 9 Section Sec # Framing / Rough -ire in�speeti®n Plans Verified Value Field Verified Value Cornments/Assumptions & Req.i® I 402.1.1, Door U-factor. U- U- ❑Complies See the Envelope Assemblies 402.3.4 ❑Does Not tablefor values. [FR1]1 []Not Observable ❑Not Applicable 402.1.1, Glazing U-factor (area -weighted U- U. ❑Complies See the Envelope Assemblies 402.3.1, average). []Does Not table for values. 402.3.3, []Not Not Observable [FR2]1 ❑Not Applicable 303.1.3 'U-factors of fenestration products ❑Complies [FR4]1 are determined in accordance ❑Does Not with the NFRC test procedure or ❑Not Observable - Itaken from the default table. ❑Not Applicable 402.4.1.1 ;Air barrier and thermal barrier ❑Complies [FR23]1 :installed per manufacturer's ❑Does Not ;instructions, ❑Not Observable ❑Not Applicable 402.4.3 Fenestration that is not site built ❑Complies [FR20]1 is listed and labeled as meeting ❑Does Not AAMA /WDMA/CSA 1011I.S.2/A440 ❑Not Observable ,or has infiltration rates per NFRC ❑Not Applicable 400 that do not exceed code limits. 402.4.5 IC -rated recessed lighting fixtures ❑Complies [FR16]2 sealed at housing/interior finish ❑Does Not and labeled to indicate :52.0 cfm ❑Not Observable .leakage at 75 Pa, ❑Not Applicable 403.3.1 Supply and return ducts in attics ❑Complies [FR12]1 "insulated >= R-8 where duct is []Does Not Q >= 3 inches in diameter and >_ ❑Not Observable R-6 where < 3 inches. Supply and ❑Not Applicable return ducts in other portions of ,the building insulated >= R-6 for Idiameter >= 3 inches and R-4.2 ;for < 3 inches in diameter. 403.3.2 Ducts, air handlers and filter ❑Complies [FR1311 boxes are sealed with ❑Does Not ;joints/seams compliant with ❑Not Observable International Mechanical Code or ❑Not Applicable International Residential Code, as applicable. 403.3.5 Building cavities are not used as ❑Complies [FR15]3 ducts or plenums. ❑Does Not ❑Not Observable ❑Not Applicable 11 High Impact (Tier 1) 2 1 Medium Impact (Tier 2) 3 1 Low Impact (Tier 3) 1 Project Title: carmack res Report date: 02/08/22 Data filename: Page 4 of 9 Section # Framing / Rough -In Inspection Plans Verified Value Field Verified Value Complies? Comments/Assumptions & Req.ID 403.3.7 Ducts declared to be within the ❑Complies [FR28]3 conditioned space are either 1) ❑Does Not completely within the continuous ❑Not Observable air barrier and within the building ❑Not Applicable thermal envelope, 2) buried within ceiling insulation in accordance with Section R403.3.6 and the air handler is located completely within the continuous air barrier and within the building thermal envelope and the duct leakage is <= 1.5 cfm / 100 square feet of conditioned floor area served by the duct system, or 3) the ceiling insulation R-value installed against and above the insulated duct >= to the proposed ceiling insulation R-value, less the R- value of the insulation on the 403.4 HVAC piping conveying fluids R- R- ❑Complies (FR1712 above 105 °F or chilled fluids ❑Does Not below 55 4F are insulated to 2:_R- ❑Not Observable 3, ❑Not Applicable 403.4.1 Protection of insulation on HVAC ❑Complies [FR2411 piping. ❑Does Not ❑Not Observable ❑Not Applicable 403.5.3 Hot water pipes are insulated to R- R- ❑Complies [FR18]2 >—R-3. ❑Does Not ❑Not Observable ❑Not Applicable 403.6 Automatic or gravity dampers are ❑Complies [FR1912 installed on all outdoor air ❑Does Not intakes and exhausts. ❑Not Observable ❑Not Applicable Additional Comments/Assumptions: 111 High Impact (Tier 1) 12 1 Medium Impact (Tier 2) 13 1 Low Impact (Tier 3) Project Title: carmack res Report date: 02/08/22 Data filename: Page 5 of 9 Section # Insulation Inspection Plans Verified Value Field Verified Value Complies? Comments/Assumptions & Req.ID 303.1 All installed insulation is labeled ❑Complies [IN13]2 or the installed R-values ❑Does Not provided, []Not Observable ❑Not Applicable 402.1.1, ; Wall insulation R-value. If this is a ' R- R- '❑Complies See the Envelope Assemblies 402.2.5, mass wall with at least 1/z of the ❑ Wood ❑ Wood ❑Does Not table for values. 402.2.6 [IN3]1 4 wall insulation on the wall exterior, the exterior insulation Mass ❑ Mass ❑Not Observable requirement applies (FR10). ❑ Steel ❑ Steel [Not Applicable 303.2 Wall insulation is installed per ❑Complies [IN4]1 manufacturer's instructions. ❑Does Not ❑Not Observable ❑Not Applicable Additional Comments/Assumptions: 1 I High Impact (Tier 1) 2 1 Medium Impact (Tier 2) 3 1 Low Impact (Tier 3) Project Title: carmack res Report date: 02/08/22 Data filename: Page 6 of 9 Section # Final Inspection Provisions Plans Verified Value Field Verified Value Complies? Comments/Assumptions & Req.ID 402.1.1, 'Ceiling insulation R-value. R- R- ❑Complies See the Envelope Assemblies 402.2.1, ❑ Wood ❑ Wood ❑Does Not table for values. 402.2.2, [] Steel ❑ Steel ❑Not Observable 402.2.6 [Fill' ❑Not Applicable 303.1.1.1, Ceiling insulation installed per ❑Complies 303.2 manufacturer's instructions. ❑Does Not [FI2]' Blown in marked every ❑Not Observable 300 ft2. ❑Not Applicable 402.2.3 Vented attics with air permeable ❑Complies [FI22]2 insulation include baffle adjacent ' ❑Does Not to soffit and eave vents that ❑Not Observable extends over insulation. ❑Not Applicable 402.2.4 (Attic access hatch and door R- R- '❑Complies [FI3I1 :insulation ?R-value of the❑Does Not adjacent assembly. ❑Not Observable ❑Not Applicable 402.4.1.2 Blower door test @ 50 Pa. <=5 ACH 50 = ACH 50 = ❑Complies [FI17]' ,ach in Climate Zones 1-2, and ❑Does Not <=3 ach in Climate Zones 3-8. ❑Not Observable ❑Not Applicable 403.3.3 Ducts are pressure tested to cfm/100 cfm/100 ❑Complies [171271' determine air leakage with ft2 ft2 ❑Does Not either: Rough -in test: Total ❑Not Observable leakage measured with a ❑Not Applicable pressure differential of 0.1 inch �w.g. across the system including :the manufacturer's air handler enclosure if installed at time of test. Postconstruction test: Total leakage measured with a 'pressure differential of 0.1 inch w.g. across the entire system including the manufacturer's air handler enclosure. 403.3.4 Duct tightness test result of <=4 cfm/100 cfm/100 ❑Complies [F1411 cfm/100 ft2 across the system or ft2 ft2 ❑Does Not <=3 cfm/100 ft2 without air ❑Not Observable handler @ 25 Pa. For rough -in ❑Not Applicable tests, verification may need to ;occur during Framing Inspection. 403.3.2.1 (Air handler leakage designated ❑Complies [FI24]1 by manufacturer at <=2% of ❑Does Not design air flow. ❑Not Observable ❑Not Applicable 403.1.1 Programmable thermostats ❑Complies [17I9]2 installed for control of primary ❑Does Not heating and cooling systems and []Not Observable initially set by manufacturer to ❑Not Applicable code specifications. 403.1.2 Heat pump thermostat installed❑Complies [F110]2 on heat pumps. ❑Does Not ❑Not Observable ❑Not Applicable 403.5.1 'Circulating service hot water ❑Complies [FI1112 systems have automatic or ;❑Does Not accessible manual controls. ❑Not Observable ❑Not Applicable 111 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: carmack res Report date: 02/08/22 Data filename: Page 7 of 9 I Section # Final Inspection Provisions Plans Verified Value Field Verified Value Complies? Comments/Assumptions & Req.ID 403.6.1 All mechanical ventilation system ❑Complies [F[25]2 fans not part of tested and listed ❑Does Not HVAC equipment meet efficacy []Not Observable and air flow limits per Table ❑Not Applicable R403.6.1. 403.2 Hot water boilers supplying heat ❑Complies [F126]2 through one- or two -pipe heating []Does Not systems have outdoor setback ❑Not Observable control to lower boiler water ❑Not Applicable temperature based on outdoor temperature. 403.5.1.1 Heated water circulation systems ❑Complies [FI28]2 have a circulation pump. The ❑Does Not system return pipe is a dedicated ❑Not Observable return pipe or a cold water supply ❑Not Applicable pipe. Gravity and thermos- syphon circulation systems are not present. Controls for circulating hot water system pumps start the pump with signal for hot water demand within the occupancy. Controls automatically turn off the pump when water is in circulation loop is at set -point temperature and no demand for hot water exists. 403.5.1.2 Electric heat trace systems ❑Complies [F129]2 comply with IEEE 515.1 or UL []Does Not 515. Controls automatically adjust the energy input to the ❑Not Observable heat tracing to maintain the ❑Not Applicable desired water temperature in the piping. 403.5.2 Demand recirculation water ❑Complies [F130]2 systems have controls that ❑Does Not manage operation of the pump []Not Observable and limit the temperature of the water entering the cold water ❑Not Applicable piping to <= 1044F. 403.5.4 _ Drain water heat recovery units ❑Complies [FI31]2 tested in accordance with CSA ❑Does Not B55.1. Potable water -side pressure loss of drain water heat ❑Not Observable recovery units < 3 psi for ❑Not Applicable individual units connected to one or two showers. Potable water- side pressure loss of drain water heat recovery units < 2 psi for individual units connected to three or more showers. 404.1 90% or more of permanent ❑Complies [FI6]1 fixtures have high efficacy lamps. ❑Does Not ❑Not Observable ❑Not Applicable 404.1.1 Fuel gas lighting systems have ❑Complies (F123]3 no continuous pilot light. ❑Does Not ❑Not Observable ❑Not Applicable 401.3 Compliance certificate posted. ❑Complies [F17]2 ❑Does Not ❑Not Observable ❑Not Applicable 1 I High Impact (Tier 1) 12 1 Medium Impact (Tier 2) 1 3 1 Low Impact (Tier 3) Project Title: carmack res Report date: 02/08/22 Data filename: Page 8 of 9 a1U%;1WNe Plans Verified Field Verified Final Inspection ProvisionsPlains Value Complies? Comments/i4,ss�s�uvptioo�s & Req.ID 303.3 Manufacturer manuals for ❑Complies [F[18]3 :mechanical and water heating ❑Does Not systems have been provided. ❑Not Observable []Not Applicable Additional Comments/Assumptions: 111 High Impact (Tier 1) 2 Medium Impact (Tier 2) 13 1 Low Impact (Tier 3) Project Title: carmack res Report date: 02/08/22 Data filename: Page 9 of 9 2018 IECC Energy Efficiency Certificate Insulation Rating R-Value Above-Grade00 Below -Grade Wall 23.00 Floor 0.00 Ceiling / Roof 50.00 Ductwork (unconditioned spaces): Window 0.30 Door 0.15 Heating & Cooling Equipment Efficiency Heating System: Cooling System: Water Heater: Name: Date: Comments