HomeMy WebLinkAboutRESCHECK - 04-00111 - 653 Vale Lane - New SFRREScheck Compliance Certificate
2000 IECC
Generated by REScheck- Web Software
PROJECT TITLE: Home for Rusty and JoAnna Sutherland
CITY: Rexburg
STATE.- Idaho
HDD: 8693
CONSTRUCTION TYPE: Single Family
DATE: 03/30/04
DATE OF PLANS: Feb. 11 2004
PROJECT DESCRIPTION:
Single family dwelling
DESIGNEWCONTRACTOR:
HDC Drafting, LLC
COMPLIANCE:- Passes
Maximum UA = 453
Your Home UA = 336
25.8% Better Than Code (UA)
Ceiling 1: Flat or Scissor Truss
Wall I.- Wood Frame, 16" o.c.
Door 1: Solid
Window 1 - Vinyl Frame, 2 Pane w/ Low -E
Basement Wall 1: Solid Concrete or Masonry
Wall height: 8.0'
Depth below grade: 7.0'
Permit Number
Checked By/Date
Gross Glazing
Area or Cavity cont. or Door
Perimeter R -Value R - Val ue U -Factor UA
1711 50.0 0.0 44
1990 2-3.0 0.0 94
63 0.350 22
223 0-350 78
1592 i 1 24JL 0.0 64
Insulation depth: 8.0'
Window 2: Vinyl, Frame, 2 Pane w/ Low -E 0`35k 34
Furnace 1: Forced Hot Air (N on- El ectric), `A� AFUE
COMPLIANCE STATEMENT: The proposed building design described here i's consistent with the
building plans, specifications, and other calculations submitted with the permit application. The proposed
building has been designed to meet the 2000 ICC i requrements in UScstick- web and to comply with the
mandatory requirements listedo the RE heck Insp cti Checklist.
Builder/Designer.
3
Date
Mat al s and equipment must be identified s that compliance can be determined.
Manufacturermanuals for all installed heating and linequipment ars sem water r tin
equipment must be provided.
Insulation -values, glazing U -factors, and heating equipment must b
clearly marked on
thebul*ldm'gplans or specifications.
Duct Insulation:
Ducts in unconditioned spaces must be insulated t ,
Ducts. outside the building must be insulated to R-8.0.
Duct Construction
All joints, scams, and connections must be securely fastened with welds, gaskets,mastics
(adhesives), mastic- lu rn d -fabric, or tapes. Duct tape i's not permitted.
Exception: Continuously weldedand locking -type longitudinal ,Dints and sus on ducts
operating at less than ire . "a.
Ducts shall be supported every 10 feet or in accordance with the manufacturer's instructions.
Cooling ducts with exterior insulation -must covered with a vapor retarder.
Air filters are required ire the return air system.
The RVAC system must provide a means for balancing air and water sten.
Temperature Contrl
Thermostats are required for each separate HVAC system. A manual or automatic means to
partially restrict or shut off the heating and/or cooling input to each zone or floor shall be provided.
Service Water Heating*
Water heaters With vertical pipe risers must have a heat trap on both the inlet and nutlet unless the
water beater has an integral heat trap r is part of a circulating system.
Insulate circulatinghof water '
s to the levels in Table 1.
Circulating Hut Water Systems
Insulate circulating hot water pipes to the levels in Table 1.
Swimming Pools
All heated swimming poots must have an.on/off heater switch and require a
+� r unless over 20%
of the heating energy s from non-depIctable sources. Pool pumps require ulr
�a time clock.
j Heating and Cooing Piping Insulation:
] � HVAC piping conveying fluids abase 1175 OF or chilled fluids below 55 OF must be insulated to the.
� levels in Table 2.
Table 1: MiFzimum Insulation Thicknessfor Circulating
Heated WaterInsulation Thickness in Inches Is
Non -Circulating Runouts
Circulating Mains and lunut
Temperaturto1 IF to 1 " 2.011,t
1- 1 OU
100-130
0.5
0.5
Table Minimum Insulalion
t
P,es
Heating Systems
Low Pressure/Temperature
Low Temperature
Steam Condensate (for feed water
cooling systems
Mixed Water, Refrigerant,
and Brine
0.5 1.0 1.5
0,5 0.5 1.
for H VA C Pipes.
Fluid Temp. Insulation. Thickness in Inches by PI I'
ZCS
R -n F ' u out I" and Less .1.25" to " . tr to r'
201-250
1.0
1.5
1.
120-200
0-5
1.0
1.0
I
Any
1.0
1.0
1.5
2.0
-55
0.5
0.5
0.75
1.0
Below 40
1.0
1.0I
1.
NOTES TO, FIELD (Building Department Use Only)