The URL can be used to link to this page

Home My WebLink AboutRESCHECK - 06-00479 - 642 Meadowbrook St - New SFR'Y oL o0474 Permit # Permit Date r*�(, REScheck Software Version 3.7.3 Compliance Certificate Report Date: 10/23/06 Data filename: C:\Program Files\Check\REScheck\Basic.rck Energy Code: 2003 IECC Location: Rexburg, Idaho Construction Type: Single Family Glazing Area Percentage: 18% Heating Degree Days: 8693 Construction Site: Owner/Agent: Designer/Contractor: Ceiling 1: Flat Ceiling or Scissor Truss: 1591 38.0 0.0 48 Wall 1: Wood Frame, 16" o.c.: 1790 19.0 0.0 90 Window 1: Vinyl Frame:Double Pane with Low-E: 211 0.350 74 Door 1: Solid: 38 0.350 13 Door 2: Glass: 40 0.500 20 Basement Wall 1: Solid Concrete or Masonry: 1440 13.0 0.0 80 Window 2: Vinyl Frame:Double Pane: 80 0.350 28 Furnace 1: Forced Hot Air: 85 AFUE Compliance Statement: The proposed building design described here is consistent with the building plans, specifications, and other calculations submitted with the permit application. The proposed building has been designed to meet the 2003 IECC requirements in REScheck Version 3.7.3 and to comply with the mandatory requirements listed in the REScheck Inspection Checklist. Builder/Designer Company Name Date Page 1 of 4 REScheck Software Version 3.7.3 Inspection Checklist Date: 10/23/06 Ceilings: ❑ Ceiling 1: Flat Ceiling or Scissor Truss, R-38.0 cavity insulation Comments: Above -Grade Walls: ❑ Wall 1: Wood Frame, 16" o.c., R-19.0 cavity insulation Comments: Basement Walls: ❑ Basement Wall 1: Solid Concrete or Masonry, 8.0' ht77.0' bg/8.0' insul, R-13.0 cavity insulation Comments: Windows: ❑ Window 1: Vinyl Frame:Double Pane with Low-E, U-factor: 0.350 For windows without labeled U-factors, describe features: #Panes _ Frame Type Thermal Break?. Comments: ❑ Window 2: Vinyl Frame:Double Pane, U-factor: 0.350 For windows without labeled U-factors, describe features: #Panes Frame Type Thermal Break?, Comments: Doors: ❑ Door 1: Solid, U-factor. 0.350 Comments: ❑ Door 2: Glass, U-factor: 0.500 Comments: Heating and Cooling Equipment: ❑ Furnace 1: Forced Hot Air: 85 AFUE or higher Make and Model Number: Yes _ No Yes— No Air Leakage: ❑ Joints, penetrations, and all other such openings in the building envelope that are sources of air leakage must be sealed. ❑ Recessed lights must be 1) Type IC rated, or 2) installed inside an appropriate air -tight assembly with a 0.5" clearance from combustible materials. If non -IC rated, the fixture must be installed with a 3" clearance from insulation. Skylights: ❑ Minimum insulation requirement for skylight shafts equal to or greater than 12 inches is R-19. Vapor Retarder: ❑ Required on the warm -in -winter side of all non -vented framed ceilings, walls, and floors. Materials Identification: ❑ Materials and equipment must be installed in accordance with the manufacturer's installation instructions. ❑ Materials and equipment must be identified so that compliance can be determined. Page 2 of 4 u ❑ Manufacturer manuals for all installed heating and cooling equipment and service water heating equipment must be provided. ❑ Insulation R-values, glazing U-factors, and heating equipment efficiency must be clearly marked on the building plans or specifications. Duct Insulation: ❑ Supply ducts in unconditioned attics or outside the building must be insulated to R-11. ❑ Return ducts in unconditioned attics or outside the building must be insulated to R-6. ❑ Supply ducts in unconditioned spaces must be insulated to R-11. ❑ Return ducts in unconditioned spaces (except basements) must be insulated to R-2. ❑ Where exterior walls are used as plenums, the wall must be insulated to R-11. ❑ Insulation is not required on return ducts in basements. Duct Construction: ❑ Duct connections to flanges of air distribution system equipment must be sealed and mechanically fastened. ❑ All joints, seams, and connections must be securely fastened with welds, gaskets, mastics (adhesives), mastic -plus -embedded -fabric, or tapes. Tapes and mastics must be rated UL 181A or UL 181 B. Exception: Continuously welded and locking -type longitudinal joints and seams on ducts operating at less than 2 in. w.g. (500 Pa). ❑ The HVAC system must provide a means for balancing air and water systems. Temperature Controls: ❑ Thermostats are required for each separate HVAC system. A manual or automatic means to partially restrict or shut off the heating and/or cooling input to each zone or floor shall be provided. Service Water Heating: ❑ Water heaters with vertical pipe risers must have a heat trap on both the inlet and outlet unless the water heater has an integral heat trap or is part of a circulating system. ❑ Insulate circulating hot water pipes to the levels in Table 1. Circulating Hot Water Systems: ❑ Insulate circulating hot water pipes to the levels in Table 1. Swimming Pools: ❑ All heated swimming pools must have an on/off heater switch and require a cover unless over 20% of the heating energy is from non-depletable sources. Pool pumps require a time clock. Heating and Cooling Piping Insulation: ❑ HVAC piping conveying fluids above 105 degrees F or chilled fluids below 55 degrees F must be insulated to the levels in Table 2. Page 3 of 4 Table 1: Minimum insulation Thickness for Circulating Hot Water Pipes Insulation Thickness in Inches by Pipe Sizes Non -Circulating Runouts Circulating Mains and Runouts Heated Water Temperature (°F) Up to 1" Up to 1.25" 1.5" to 2.0" Over 2" 170-180 0.5 1.0 1.5 2.0 140-169 0.5 0.5 1.0 1.5 100-139 0.5 0.5 0.5 1.0 Table 2: Minimum Insulation Thickness for HVAC Pipes Insulation Thickness in Inches by Pipe Sizes Fluid Temp. Piping System Types Range(OF) 2" Runouts 1" and Less 1.25" to 2.0" 2.5" to 4" Heating Systems Low Pressure/Temperature 201-250 1.0 1.5 1.5 2.0 Low Temperature 106-200 0.5 1.0 1.0 1.5 Steam Condensate (for feed water) Any 1.0 1.0 1.5 2.0 Cooling Systems Chilled Water, Refrigerant and 40-55 0.5 0.5 0.75 1.0 Brine Below 40 1.0 1.0 1.5 1.5 NOTES TO FIELD: (Building Department Use Only) Page 4 of 4 0600479 642 Meadowbrook St -Price REScheck Compliance Certificate 2003 IECC REScheck Software Version 3.6 Release la Data filename: C:\Program Files\Check\REScheck\2006 Chad Price.rck PROJECT TITLE: Rhett Price Residence CITY: Rexburg STATE: Idaho HDD: 8693 CONSTRUCTION TYPE: Single Family WINDOW / WALL RATIO: 0.07 DATE: 10/13/06 DATE OF PLANS: October 2006 PROJECT DESCRIPTION: Wood Frame Construction DESIGNER/CONTRACTOR: Design Intelligence, LLC COMPLIANCE: Passes Maximum UA = 590 Your Home UA = 545 7.6% Better Than Code (UA) Checked By/Date lei E O U OCT 1 3 2006 D CITY OF REXBURG �i Gross Glazing �5a5 Area or Cavity Cont, or Door Perimeter R-ValueR Value -Facto TA Ceiling 1: Flat Ceiling or Scissor Truss 1591 38.0 0.0 48 Wall 1: Wood Frame, 16" o.c. 1790 19.0 0.0 107 Gables: Wood Frame, 16" o.c. 723 19.0 0.0 30 Window 1: Vinyl Frame:Double Pane with Low-E 20 %931 0.320 56 Door 1: Solid 40 0.560 22 Basement Wall 1: Solid Concrete or Masonry Io(gD • I&H, 13.0 0.0 95 Wall height r^ 'P�°N`s Depth below 1 `� Insulation depth 8.0' Floor 1: Slab -On e:Unheated 179 0.0 187 Insulation depth: 0.0' Furnace 1: Forced Hot Air, 85 AFUE , COMPLIANCE STATEMENT: The proposed building design described here is consistent with the building plans, specifications, and other calculations submitted with the permit application. The proposed building has been designed to 2 �4-67T PPIu; u ovEn OCT 1 0 2006 D CITY OF REXBURG 14,CIT VMS*, E c E w E OCT 10 2006 Lu) CITY OF REXBURG 901 Mewctai /;roI