HomeMy WebLinkAboutRESCHECK - 06-00101 - 311 Seagull Dr - New SFRk
t
.t
0
311 Seagull Dr-Merrill
REScheck Software Version 3.7.3
Compliance Certificate
Report Dat : 02/24/06
Data filename., Untitl d.r l
Energy Code.
Location:
Construction T p :
Glazing Area Percentage:
Heating Degree Days:
2000 I ECC
Rexburg, Idaho
Single Family
13%
693
Construction Site:
Block 6 Lot 8 Henderson Subdivition
Rexburg, l D 8344
Owner/Agent.-
Anthony
r . rpt.Anthony M rrill
Merrill Construction
1322 N, 16 th. E.
Sugar City , ID 83448
356-x-276
rnc,buld4tj@ida.net
Des i n r/Cort racto r. -
Anthony Merrill
Merrill o n tru nti o ri
1322 N. 16th, E
Sugar- City, ire 83448
356-4276
r cbu(du@id }n t
Wall 1: Woad Frame 16" . ,
Window I; Vinyl Frame:Dioubfe Pane ith LOW—E:
Door- 1: olid:
Door : la:
Basement Wall 1: Solid Concrete or Masonry:
Furnace 1: Forced Hot Air: 90 AFUE
20
1350
.0
21.0
13.0
0.330
0.350
0.350
38,
55
43
1
7
Compliance Statement.- The Proposed building design scribed Fere is consistent with the building plans
lulatir� ��r�itt� itis t� alt ����r�. T � specifications, and othercacoh PrP �1 building has been designed to meet the 2000
� requirements °rREScheck ri�� � �n �� �� its t� n rdt�r�uirr�t listed
i n the 1� Inspection
ild r/D
CO pant' Name
Date
Page I of
Date: 02124/06
Ceilings:
REScheck Software Version 3.7.3
Inspection Checklist
D Ceiling. 1: Flat Ceiling or Scissor Truss, R-38.0 continuous insulation
Comments-
Above-Grade
omments:
Abo -Grade Walls:
Lj Wall 1 ''mood Frame, 16" o. . s R-21.0 cavity insulation
n
Comments:
Basement Wal is
Ll Basement Wali 1: Solid Concrete or Masonry, . ' ht/'.0' b / . ' in uI R-13.0 .0 it insulation
Comments:
Windows:
Lj Window 1: 'Vinyl Frame:Double Pane with L � , Ul-f tar: 0.330
For windows without i b l d -factor, describe features:
#manes Frame Type Thermal Break? � Yes No
Comments.
Doors,:
El Door 1: Solid, -factor: 0.350
Comments:
:
LJ Door : Glass, -factor: 0.350
Comments:
Meeting and Cooling Equipment:
Ll Furnace 1: Forced Hot Air: 90 AFI F or higher
ll/laice and Mallei Number,
Air Leakage:
Joints, penetrations, and a l l other such openings in the building ere t o
pthat are our of air leakage must be sealed.
Ll Recessed lights mut be 1 ) Type IC rated, air ) installed inside nr� r�air-tight
�� � �t� assembly with " clearance from
combustible materials. if non -IC rated, the fixture must be installed with a 3'° clearance from insulation.
Vapor Retarder:
[i Required on the warm -in -winter side of all non -vented framed ceilings,
Materials Identification
Ll Materials and equipment must be installed in accordanre with the manufacturers
installation instructions.
Lj Materials and equipment must t identified that compliance Carn be determined.
Lj Manufacturer manuals for all installed heating and cooling equipment and service heating n equipment must be provided.
Ll f res u Iation -values, glazing -factors, and heating u i pm nt efficiency mut.
specifications.
bIrl rT�r� n thebuilding plans or
Duct Insulation.,
L! Ducts in unconditioned spaces must be insulated t R-5. Ducts outside
. the building must be insulated t -.0.
Duct Construction:
All joints, seams, and connectionr> must be securelyfastened with wefds,
mastic-plu -embedded-fabric., or tapes. Tapes and mastics must b rated L `1 1 r L 181
Exception-, Continuously welded and I l irig- longitudinaljoints
Pa).
�d � ducts �p�rt�r� t # than wn .
Ll The HVAG system rust provide a means for balancing air and water systems.
Temperature Controls:
w.g. (500
L] Thermostats r required for each separate H' a�
��1 r ��r�t�c means to partially rstnt or phut off the
heating and/or cooling input to each zone or floor shall be provided.
Service Water Heating:
Water Festers with vertical PiPe risers must have a heat trap on both the irrl t and outlet t unIs the water heater has n
heat trap or is part of a circulating system.
Insulate i r u lati n riot water pipes to the levels in Table I
Circulating Hot 'mater Systems:
❑ Insulate circulating hot water pt'pes to the levels in Table 1.
Swimming Pools:
integral
All heated swimming pools must have ars onloff heater switch and require a cover unless or 0% of the heating energy is from
n ri-d pl tabl sources. Pool pumps require a time dock,
Heating and Cooling Piping Insulation:
HVAC piping conveying fluids above 105 degrees r or chilled fluids below 55 degrees y
� u� � insulated t # �I r� TIMI
f
Page 3 of
R
Table I-, Minimum Insulatfon Thickness for Circulating Hot Water
Heated Water
Temperature (°F)
17Q-180
140-169
100-139
Insulation Thickness 'in Inches by Pipe izes
Non -Circulating Runouts
Up to I
.
.
.
Lip to 1.25'p
1.
0.
0,5
Table l : Minimum Insulation Thickness for HVA C Pipes
Fluid Temp.
Piping System Types .an(' F
Heating Systems
Low Pressure/Temperature 1-250
Low Temperature 120-200
Stearn Condensate (fog- feed water) Any
Cooling Systems
Grilled Water, fr r nt and 40-55
Brine Below 40
NOTES 7O FlELD: [Building Department Use Only)
ircul tin
1.5" to 2.0"
Mains and Runouts
Fuer 2,
IF
.
1.
1.0
Insulation Thickness in Inches by Pipe Sizes
" Runouts
lip and Less 1.251P to 2.011 2.517
to 41F
'1:. 0
1.5
l i5
2,0
0.5
1.0
1.
1-5
1.0
1.0
1.5
2,0
0.5
0.5
0.75
1.