HomeMy WebLinkAboutRESCHECK - 06-00082 - 4464 N Salem Hwy - Mech.477
4
t
W.
REScheck Software Version 3.7.3
Compliance Certificate
Report Date: 02/15106
Data filename: C-Trogram FileskCheckkREScheck\house.rck
Energy Code.-
Location:
ode:Location:
Construction Types
lazing ,area Percentage-.
Heafing Degree Days:
Construction Site:
2000 IECC
Rexburg, Idaho
Single gamily
100%
8693
Owner/Agent:
0
Per, I kit 441
Perini at
Designer/ Contractor,
Ceiling I . Flat Ceiling or Scissor Truss:
3174
o
M
1803
Wall 1. Wood Frame, 16'
o,c--- 3174 0.0 0.0
Window 1Vinyl Frame -.Double Pane with Low -E: 3174 OMO0
Door 1: Solid: 3174 0.000
Floor 1: All -Wood J i t/T :Over Unconditioned Space: 3174790
Crawl 1: mid Concrete or Masons 3174 0,0 0,0 1120
Fu ace 1: Forced Hot Air: 91 AFUE
Page 1 of 4
Date : 02/15106
Ceilings:
REScheck Software Version 3.7.3
Inspection Checklist
L] Ceiling 1: Flat Ceiling or Scissor Truss, R-0 (uninsulateid)
Comments:
Above -Grade Walls:
[j Wall 1: Wood Frame, 16" ox, l Oninsulated)
Comments -
Windows:
Ll Window 1; Vinyl FrameDouble Pane with Low -E, -factor- 0.000
For windows Wthout labeled -factors, describe features:
#Panes Frame Type
en meat :
Doors.-
E]
oors=
❑ Door 1: Solid, U factor: 0.000
Comments-
Floors,:
omrye t:
Floor
Thermal Break? Yes o
L) Floor 1 - Ali -Wood Joistffrvss:Over Unconditioned Spaces, R-0 (uninsulated)
Comments-
ra Space all
L) C ravel : Solid Concrete o r M ason ry, 4. ' ht/3-O' .0' insul,(uninsulated)
Comments:
Heating and Cooling E uiprn t,
0 Furnace 1. Forced Hot Ain 91 AFUE or higher
Make and Model Number-.
Air Leakage:
Joints, penetration , and all tither such openings in the building envelope that are sources of air leakage mut be sealed.
Recessed lights m t be 1 Type IC rated, or 'installed i aside ars appropriate air `tight assembly with a 0.5TIclearance from
om hustible materials. if non -1 C rated, the fixture must. be installed with a 3" clearance from insulation,
Vapor Retarder:
Required on the 'iii" -winter &ide of all non -vented framed c -I ngs,a'ff-5, and Hors_
i
Materials and equipment must be installed in accordance W-ththe manufactureVs installation instructions,
Materials and equipment must be identified so that cornpflance can be determined-
Manufacturer
et rm n d.nuf : tur r manuals for all installed heating and cooling equipment and serine water heating equipment must be provided.
Insulation I -values, glazing -factor, and beating equipment efficiency must be clearly marked on the building fans or
speCifications.
Duct insulation
I
XT
W..
f„J Ducts in unconditioned spaces must be insulated to R-5. ducts outside the building rust be insulated to R-8.0.
Duct oro. -
All joints, seam ,, and connections must be r l fastened vVith welds, gaskets, mastics (adhesives),
mastic-plusrnb d . I -tab 6 , or tapes. Tapes and masfics must be rated UL 181 A or UL 181 B.
E pti : Continuously welded and locking -type lon tudinal joints and seams on duets operating at less than 21n, w.g. 500
Pa).
:] The HVAC system must provide a mans for balancing air and water systems.
Temperature Controls
C3 Thermostats ars required for each separate HVAC system. A manual or automatic mens to partially restrict or shut off the
heating and/or cooling input is each zone or floor shill be provided.
SeMce Water Hating=
L] Water heaters with vertical pipe risers must have a heat trap on both the inlet and outlet unless the water heater has an integral
heat trap or is part of a circulating system.
[J Insulate circulating hot water pipes to the levels in Table 1.
Circulating Hot Fater Systems;
A Insulate circulating hat water pipes to the levels in Table 1.
Swimming Pools
J All heated swimming pools must have an onloff heater sw4tch and require a cove` unless over 20% of the heating energy is from
non-depletable sources. Pool pumps require a time clork.
Heating and Cooling Piping Insulation:
J HVAC piping conveying fluids above 105 degrees F or chilled fluids below degrees 1= must to insulated to the levels in Table
.
Page 3 of 4
Table - Minimum Ins lo Thickness for CircuWing Hot Wgq ter Pip es
Heated Water
Temperature(:DF)_
170- 1 0
140-1169
100-139
Insulation Thickness in laches by Pipe Sizes
lion- it ulat nunouts Circulating Mains and Runouts
Up to I it
.
0.5
0.
Up to 1,251)
1.
.
.
Table 2.0 Minimum ins ula tion Thickness for H VA C pip es
Fluid Temp.
Piping System Types an ff
Heating Systems
Lav Pressure/Temperature
Low Temperature-
Steam
emperatureSteam Condensate (for feed water)
Cooling Systems
Chilled Water, Refrigerant and
Bnln
1,51' to 2.011
Over "
Insulation Thickness in Inches by Pipe Sizes
" Runouts
lie and Less
1,2571 to 2.011
201-250
1.0
1
1.
120-200
.
1.0
1.0
1.
Any
1.0
1.0
1.
40-
0.75
1-0
Below 40
1.0
1.0
1.
1.
NOTES TO FIELD: (Building Department Use Only)
Page