The URL can be used to link to this page

Home My WebLink AboutCOMPLIANCE CERTIFICATE & LETTER - 07-00028 - 265 Polo Dr - New SREScheck Software Version 4.0.1 Compliance Certificate Project Title: Henderson Addition Report Date: 02/08/07 Data filename: C:\DOCUME-1\Me\MYDOCU-1\MASONS-1\HENDER-1.RCK Energy Code: 2003 IECC Location: Rexburg, Idaho Construction Type: Single Family Glazing Area Percentage: 20% Heating Degree Days: 8693 Construction Site: Block 7 Lot 13 Rexburg, ID 83440 Crooner/Agent: Mason Haycock Designer/Contractor: Chuck Doman Compliance: Passes Maximum UA: 366 Your Home UA: 366 --> 0.0% Better Than Code (UA) Calling 1: Flat Ceiling or Scissor Truss: Wall 1: Wood Frame, 16" o.c.: Door 1: Solid: Door 2: Solid: Door 3: Glass: Window 1: Vinyl Frame, Double Pane with low-E: RG Lyfnl' Basement Wall 1: Wood Frame: Wall height: 8.0' Depth below grade: 7.0' Insulation depth: 8.0' Floor 3: All -Wood Joist/rruss:Over Unconditioned Space: Furnace 1: Forced Hot Air: 85 AFUE 1900 1700 38.0 1740 21.0 20 20 40 303 1700 21.0 28 21.0 0.0 51 6.0 62 0.350 7 0.540 11 0,500 20 0.450 136 0.0 78 8.0 1 Compliance Statement The proposed building design described here is consistent with the building plans, specifications, and other calculations submitted with the permit application. The proposed building has been designed to meet the 2003 IECC requirements in REScheck Version 4.0.1 and to comply with the mandatory requirements listed In the REScheck Inspection Checklist. Name -Title Signature uace Henderson Addition Page 1 of 1 `wr Permit # Permit Date REScheck Software Version 3.7.3 Compliance Certificate Report Date: 02/08/07 Data filename: C:\Program Files\Check\REScheck\Basic.rck Energy Code: 2003 IECC Location: Rexburg, Idaho Construction Type: Single Family Glazing Area Percentage: 19% Heating Degree Days: 8693 Construction Site: Owner/Agent: Designer/Contractor: Ceiling 1: Flat Ceiling or Scissor Truss: 1800 38.0 0.0 54 Wall 1: Wood Frame, 16" o.c.: 1780 21.0 0.0 84 Window 1: Vinyl Frame:Double Pane with Low-E: 227 0.450 102 Door 1: Solid: 40 0.350 14 Door 2: Glass: 40 0.500 20 Basement Wall 1: Solid Concrete or Masonry: 1424 21.0 0.0 57 Window 2: Vinyl Frame:Double Pane: 96 0.500 48 Floor 1: All -Wood Joist/Truss:Over Outside Air: 28 21.0 0.0 1 Furnace 1: Forced Hot Air: 90 AFUE Compliance Statement: The proposed building design described here is consistent with the building plans, specifications, and other calculations submitted with the permit application. The proposed building has been designed to meet the 2003 IECC requirements in REScheck Version 3.7.3 and to comply with the mandatory requirements listed in the REScheck Inspection Checklist. Builder/Designer Company Name Date Page 1 of 4 12REScheck Software Version 3.7.3 .f Inspection Checklist Date: 02/08/07 Ceilings: ❑ Ceiling 1: Flat Ceiling or Scissor Truss, R-38.0 cavity insulation Comments: Above -Grade Walls: ❑ Wall 1: Wood Frame, 16" o.c., R-21.0 cavity insulation Comments: Basement Walls: ❑ Basement Wall 1: Solid Concrete or Masonry, 8.0' ht17.0' bg/8.0' insul, R-21.0 cavity insulation Comments: Windows: ❑ Window 1: Vinyl Frame:Double Pane with Low-E, U-factor._ 0.450 For windows without labeled U-factors, describe features: #Panes Frame Type Thermal Break? Yes No Comments: ❑ Window 2: Vinyl Frame:Double Pane, U-factor: 0.500 For windows without labeled U-factors, describe features: #Panes Frame Type Thermal Break? Yes No Comments: Doors: ❑ Door 1: Solid, U-factor. 0.350 Comments: ❑ Door 2: Glass, U-factor: 0.500 Comments: Floors: ❑ Floor 1: All -Wood Joist/Truss:Over Outside Air, R-21.0 cavity insulation Comments: Heating and Cooling Equipment: ❑ Furnace 1: Forced Hot Air: 90 AFUE or higher Make and Model Number: Air Leakage: ❑ Joints, penetrations, and all other such openings in the building envelope that are sources of air leakage must be sealed. ❑ Recessed lights must be 1) Type IC rated, or 2) installed inside an appropriate air -tight assembly with a 0.5" clearance from combustible materials. If non -IC rated, the fixture must be installed with a 3" clearance from insulation. Skylights: ❑ Minimum insulation requirement for skylight shafts equal to or greater than 12 inches is R-19. Vapor Retarder. ❑ Required on the warm -in -winter side of all non -vented framed ceilings, walls, and floors. Page 2 of 4 L=5 r""FA Materials Identification: ❑ Materials and equipment must be installed in accordance with the manufacturer's installation instructions. ❑ Materials and equipment must be identified so that compliance can be determined. ❑ Manufacturer manuals for all installed heating and cooling equipment and service water heating equipment must be provided. ❑ Insulation R-values, glazing U-factors, and heating equipment efficiency must be clearly marked on the building plans or specifications. Duct Insulation: ❑ Supply ducts in unconditioned attics or outside the building must be insulated to R-11. ❑ Return ducts in unconditioned attics or outside the building must be insulated to R-6. ❑ Supply ducts in unconditioned spaces must be insulated to R-11. ❑ Return ducts in unconditioned spaces (except basements) must be insulated to R-2. ❑ Where exterior walls are used as plenums, the wall must be insulated to R-11. ❑ Insulation is not required on return ducts in basements. Duct Construction: ❑ Duct connections to flanges of air distribution system equipment must be sealed and mechanically fastened. ❑ All joints, seams, and connections must be securely fastened with welds, gaskets, mastics (adhesives), mastic -plus -embedded -fabric, or tapes. Tapes and mastics must be rated UL 181A or UL 181 B. Exception: Continuously welded and locking -type longitudinal joints and seams on ducts operating at less than 2 in. w.g. (500 Pa). ❑ The HVAC system must provide a means for balancing air and water systems. Temperature Controls: ❑ Thermostats are required for each separate HVAC system. A manual or automatic means to partially restrict or shut off the heating and/or cooling input to each zone or floor shall be provided. Service Water Heating: ❑ Water heaters with vertical pipe risers must have a heat trap on both the inlet and outlet unless the water heater has an integral heat trap or is part of a circulating system. ❑ Insulate circulating hot water pipes to the levels in Table 1. Circulating Hot Water Systems: ❑ Insulate circulating hot water pipes to the levels in Table 1. Swimming Pools: ❑ All heated swimming pools must have an on/off heater switch and require a cover unless over 20% of the heating energy is from non-depletable sources. Pool pumps require a time clock. Heating and Cooling Piping Insulation: ❑ HVAC piping conveying fluids above 105 degrees F or chilled fluids below 55 degrees F must be insulated to the levels in Table 2. Page 3 of 4 Table 1: Minimum Insulation Thickness for Circulating Hot Water Pipes Insulation Thickness in Inches by Pipe Sizes Non -Circulating Runouts Circulating Mains and Runouts Heated Water Temperature (°F) Up to 1" Up to 1.25" 1.5" to 2.0" Over 2" 170-180 0.5 1.0 1.5 2.0 140-169 0.5 0.5 1.0 1.5 100-139 0.5 0.5 0.5 1.0 Table 2: Minimum Insulation Thickness for HVAC Pipes Insulation Thickness in Inches by Pipe Sizes Fluid Temp. Piping System Types Range(OF) 2" Runouts 1" and Less 1.25" to 2.0" 2.5" to 4" Heating Systems Low PressurelTemperature 201-250 1.0 1.5 1.5 2.0 Low Temperature 106-200 0.5 1.0 1.0 1.5 Steam Condensate (for feed water) Any 1.0 1.0 1.5 2.0 Cooling Systems Chilled Water, Refrigerant and 40-55 0.5 0.5 0.75 1.0 Brine Below 40 1.0 1.0 1.5 1.5 NOTES TO FIELD: (Building Department Use Only) It Page 4 of 4 \No/ `'r.✓ i January 31, 2007 City of Rexburg, Heating calculation for Nomarco Construction, New home in Henderson Subdivision, Rexburg, Idaho. As per the REScheck provided by the contractor the heat loss for the home is figured as follows. UA value: 393 Design indoor temp. = 70 F Design outdoor condition = -20 F Delta T: 90 F Heat loss = 35,370 BTU Infiltration value:.95% = 37,335 BTU Minimum BTU required = 72,705 BTU It is proposed to install a 100,000 BTU furnace with a 4 ton blower. Johnson Heating LLC HVAC License # 1327 State of Idaho