HomeMy WebLinkAboutCOMPLIANCE CERTIFICATE - 08-00096 - 245 Rebecca - New SFR9
REScheck Software Vprc;— ' " '
CompliancE og 000%
245 Rebecca St -Rockwell
Project Title: 5111-1204 Newport Std. Plan
Report Date: 08/30/07
Data filename: L\z - ResChecks\TH-1240 Newport Std Plan B-30-07.rck
Energy Code:
2003 IECC
Location:
Ammon, Idaho
Construction Type:
Single Family
Glazing Area Percentage:
13%
Heating Degree Days:
7918
Construction Site:
Owner/Agent:
Designer/Contractor:
Rockwell Development Inc.
Compliance: Passes Maximum UA: 339 Your Home UA: 251 --> 26.0% Better Than Code (UA)
Ceiling 1: Flat Ceiling or Scissor Truss: 1204 50.0 0.0
31
Wall 1: Wood Frame, 24" o .c.: 1752 22.0 0.0
82
Window 1: Vinyl Frame:Double Pane with Low -E: 163 0.320
52
Door 1: Solid: 40 0.160
6
Door 2: Glass: 33 0.340
11
Basement Wall 1: Solid Concrete or Masonry: 816 11.0 0.0
49
Wall height: 8.0'
Depth below grade: 7.0'
Insulation depth: 8.0'
Window 2: Vinyl Frame:Double Pane: 40 0.490
20
Furnace 1: Forced Hot Air: 93 AFUE
Compliance Statement: The proposed building design described here is consistent with the building plans, specifications, and other
calculations submitted with the permit application. The proposed building has been designed to meet the 2003 IECC requirements in
REScheck Version 4.0.1 and to comply with the mandatory requirements listed in the REScheck Inspection Checklist.
Name - Title Signature Date
Project Notes:
Compiled:8/30/07
TH-1204 Newport Std. Plan Page 1 of 4
REScheck Software Version 4.0.1
Inspection Checklist
Date: 08/30/07
Ceilings:
❑ Ceiling 1: Flat Ceiling or Scissor Truss, R-50.0 cavity insulation
Comments:
Above -Grade Walls:
❑ Wall 1: Wood Frame, 24" o .c., R-22.0 cavity insulation
Comments:
Basement Walls:
❑ Basement Wall 1: Solid Concrete or Masonry, 6.0' ht / 7.0' bg / 8.0' insul, R-11.0 cavity insulation
Comments:
Windows:
❑ Window 1: Vinyl Frame:Double Pane with Low -E, U -factor: 0.320
For windows without labeled U -factors, describe features:
#Panes Frame Type Thermal Break? Yes No
Comments:
❑ Window 2: Vinyl Frame:Double Pane, U -factor: 0.490
For windows without labeled U -factors, describe features:
#Panes Frame Type Thermal Break? Yes — No
Comments:
Doors:
❑ Door 1: Solid, U -factor: 0.160
Comments:
❑ Door 2: Glass, U -factor: 0.340
Comments:
Heating and Cooling Equipment:
❑ Furnace 1: Forced Hot Air: 93 AFUE or higher
Make and Model Number:
Air Leakage:
❑ Joints, penetrations, and all other such openings in the building envelope that are sources of air leakage are sealed.
❑ Recessed lights are 1) Type IC rated, or 2) installed inside an appropriate air -tight assembly with a 0.5" clearance from
combustible materials. If non -IC rated, fixtures are installed with a 3" clearance from insulation.
Skylights:
❑ Minimum insulation requirement for skylight shafts equal to or greater than 12 inches is R-19.
Vapor Retarder:
❑ Installed on the warm -in -winter side of all non -vented framed ceilings, walls, and floors.
Materials Identification:
❑ Materials and equipment are installed in accordance with the manufacturer's installation instructions.
❑ Materials and equipment are identified so that compliance can be determined.
TH-1204 Newport Std Plan Page 2 of 4
❑ Manufacturer manuals for all installed heating and cooling equipment and service water heating equipment have been provided.
F -I Insulation R -values, glazing U -factors, and heating equipment efficiency are clearly marked on the building plans or specifications.
❑ Insulation is installed according to manufacturer's instructions, in substantial contact with the surface being insulated, and in a
manner that achieves the rated R -value without compressing the insulation.
Duct Insulation:
Lj Supply ducts in unconditioned attics or outside the building are insulated to R-11.
Fi Return ducts in unconditioned attics or outside the building are insulated to R-6.
FI Supply ducts in unconditioned spaces are insulated to R-11.
Return ducts in unconditioned spaces (except basements) are insulated to R-2. Insulation is not required on return ducts in
basements.
Where exterior walls are used as plenums, the wall is insulated to R-11.
Duct Construction:
FI Duct connections to Flanges of air distribution system equipment are sealed and mechanically fastened.
All joints, seams, and connections are securely fastened with welds, gaskets, mastics (adhesives), mastic -plus -embedded -fabric,
or tapes. Tapes and mastics are rated UL 181A or UL 181 B.
Exceptions:
Continuously welded and locking -type longitudinal joints and seams on ducts operating at less than 2 in. w.g. (500 Pa).
F1 The HVAC system provides a means for balancing air and water systems.
Temperature Controls:
❑ Thermostats exist for each separate HVAC system. A manual or automatic means to partially restrict or shut off the heating and/or
cooling input to each zone or Floor is provided.
Service Water Heating:
❑ Water heaters with vertical pipe risers have a heat trap on both the inlet and outlet unless the water heater has an integral heat
trap or is part of a circulating system.
❑ Circulating hot water pipes are insulated to the levels in Table 1.
Circulating Hot Water Systems:
O Circulating hot water pipes are insulated to the levels in Table 1.
Swimming Pools:
C] All heated swimming pools have an on/off heater switch and a cover unless over 20% of the heating energy is from non-depletable
sources. Pool pumps have a time clock.
Heating and Cooling Piping Insulation:
17 HVAC piping conveying fluids above 105 degrees F or chilled Fluids below 55 degrees F are insulated to the levels in Table 2.
TH-1204 Newport Std Plan Page 3 of 4
Table 1: Minimum Insulation Thickness for Circulating Hot Water Pipes
Table 2: Minimum Insulation Thickness for HVAC Pipes
Fluid Temp. Insulation Thickness in Inches by Pipe Sizes
Piping System Types o 2" Runouts 1" and Less 1.25" to 2.0" 2.5" to 4
Range( F)
Insulation Thickness In Inches by Pipe Sizes
2.0
Low Pressure/Temperature
Non -Circulating
Runouts
Circulating Mains and Runouts
Heated Water
Up to 1"
Up to 1.25"
1.5" to 2.0"
Over 2"
Temperature (°F)
Brine
Below 40
1.0
1.0
170-180
0.5
1.0
1.5
2.0
140-169
0.5
0.5
1.0
1.5
100-139
0.5
0.5
0.5
1.0
Table 2: Minimum Insulation Thickness for HVAC Pipes
Fluid Temp. Insulation Thickness in Inches by Pipe Sizes
Piping System Types o 2" Runouts 1" and Less 1.25" to 2.0" 2.5" to 4
NOTES TO FIELD: (Building Department Use Only)
1.0
Range( F)
Heating Systems
2.0
Low Pressure/Temperature
201-250
Low Temperature
106-200
Steam Condensate (for feed water)
Any
Cooling Systems
2.0
Chilled Water, Refrigerant and
40-55
Brine
Below 40
NOTES TO FIELD: (Building Department Use Only)
1.0
1.5
1.5
2.0
0.5
1.0
1.0
1.5
1.0
1.0
1.5
2.0
0.5
0.5
0.75
1.0
1.0
1.0
1.5
1.5
TH-1204 Newport Std. Plan Page 4 of 4