HomeMy WebLinkAboutPRODUCT DATA - PIPE & FITTINGS PIPE CUT SHEET - 18-00176 - 220 S 2nd W - Arbor Cove - Bldg (C) #2 - 32 Units - New Dormitory Housing65, Songdeok-ro 212beon-gil, Ocheon-eup,
Nam-gu, Pohang-si, Gyeongsangbuk-do, Korea
T : +82-54-278-3611 / F : +82-54-278-0106
E : mspipe@hanmail.net / W : www.mspipe.co.kr
Designation
ASTM A53 Grade A Type E
Scope
Dimensions and Weights
Chemical Requirements (%)
* The total composition for these five elements shall not exceed 1.00%
Tensile Requirements
Tensile strength, min, psi 48 000
Yield strength, min, psi 30 000
Elongation in 2 in. Refer to A53 Table X4.1, latest revsion A53/A53M
and FM Approved for use in fire protection systems. This pipe is suitable for joining by cut or rolled groove, threading,
welding, and fittings for plain end pipe, depending on the dimensions.
This specification covers welded black and hot-dipped galvanized steel pipe. It is intended for mechanical and pressure
applications as well as ordinary uses in steam, water, gas and air lines. MS PIPE ASTM A53/A135/A795 is UL Listed
Product Submittal Data
OD thickness weight thickness weight thickness weight thickness weight
in.in.lb/ft in.lb/ft in.lb/ft in.lb/ft
1 1.315 --0.109 1.41 0.133 1.68 0.179 2.17
1 1/4 1.660 0.083 1.40 0.109 1.81 0.140 2.27 0.191 3.00
1 1/2 1.900 0.095 1.83 0.109 2.09 0.145 2.72 0.200 3.63
2 2.375 0.095 2.31 0.109 2.64 0.154 3.66 0.218 5.03
2 1/2 2.875 0.083 2.48 0.120 3.53 0.203 5.80 0.276 7.67
3 3.500 0.090 3.29 0.120 4.34 0.216 7.58 0.300 10.26
4 4.500 0.101 4.76 0.120 5.62 0.237 10.80 0.337 15.00
Super Flow (SCH 7)SCH 10 SCH 40 SCH 80
NPS
Plain End
Type E C Mn P S Cu*Ni*Cr*Mo*V*
Grade A 0.25 0.95 0.05 0.045 0.4 0.4 0.4 0.15 0.08
MS-151016
Hydrostatic Test
Permissible Variation
weight The weight of pipe shall not vary more than ± 10 % from its specified weight
Diameter pipe NPS 1 1/2 or smaller ± 1/64 in.
pipe NPS 2 or larger ± 1 %
Thickness At any point the minimum wall thickness shall not be more than 12.5% under the specified
wall thickness
End Finish
Plain ends pipe NPS 1 1/2 or smaller Manufacturer's option, unless otherwise specified.
pipe NPS 2 or larger (SCH 40/80)Beveled to an angle of 30°, +5°, -0° with root face of
1/16 in. ± 1/32 in.
Threaded ends ANSI B 1.20.1
Couplings Specifiaction A865
Bending Test (Cold)
pipe NPS 2 and Smaller
Degree of bend Diameter or mandrel
Standard 90°12x pipe OD
Close coiling 180°8x pipe OD
Flattening Test
Position weld at 90° (0°) from the direction of force and flatten until the OD is 2/3 (1/3) of the original outside
diameter to test quality of the weld. No cracks or breaks shall occur along the inside or outside surface of the weld.
Product Marking
Unless the marking is specified in the purchase order, each length of the pipe shall be legibly and continuously marked
on the outside surface with the following:
Manufacturer, Buyer, Super Flow (SCH 7 only), Specification, Type of pipe, Size, Rated Working Pressure and CRR (SCH
7 only), UL Listing and FM Approval (for fire sprinkler pipe), Heat no., Date, and Origin.
800
2500
2500
SCH 7, psi
-
1800
1800
1400
1000
900
1900
850
1800
700
20001 1/2
2
2 1/2
3
4
1600
1500
1200
900 2700
2220
1800
2500
1200
2300
2500
2900
2300
NPS SCH 10, psi SCH 40, psi
1200
1
1 1/4
SCH 80, psi
MS-151016